فحص خطوط fastlink ADSL

8/14/2019 fastlink ADSL

1/15

ADSL

) FAST LINK (

/

/

FAST LINK

6DSL) AL4 (

1


2/15

AL4 POSU POTS Splitter Unit ((.

2


3/15

PHUBS PHUBSAccess Integrator (ACI 8.3.64.2b(

2000 4Windows 2000 (SP4 (. :

* Connection via Ethernet (LCT to PHUBS), use a Cross-over LAN cable. See illustrationbelow.

PHUBS

IP address 192.168.1.2. Process monitor LCT:

1. PHUBS

2. Process monitor LCT

3


4/15

3. In the DCN Root, double-click on SNMP-PORT#1 andin the window that appears, click on SNMP_PORT#1.Click on Configuration NE Configuration InsertSNMP Network Element.

4. Insert SNMP network element window will appearand type in the following parameters shown. Apply then

4


5/15

Close. After which, a plus sign would appear before theSNMP_PORT#1.

PHUB First Setup Procedure PHUB

5


6/15

1. Connect the cross LAN cable from the LCT (laptop) to the 100bT terminal ofthe PHUB. Take note that the IP address of the LCT should be in the network of192.168.1.0, Do not use 192.168.1.1 which is the outband IP of the PHUB.

2. Open the ACI LCT by double-clicking the Process monitor LCT.

3. In the DCN Root, double-click on SNMP-PORT#1 and in the window thatappears, click on SNMP_PORT#1. Click on Configuration NE Configuration Insert SNMP Network Element

4. Insert SNMP network element window will appear and type in the following

parameters shown. Apply then Close. After which, a plus sign would appearbefore the SNMP_PORT#1.

6


7/15

5. Click on the + sign and then click on the Packet Hub NE. Click on Utilities Scripting Execute Script

6. Execute the script file phubsnmp.tcl. Look inC:\AccessIntegrator\scripts\snmpne\phub.

7. PHUB Scripts 192.168.1.1 window will appear, and type e to edit

parameter file. After which, phubparams.tcl notepad window will appear andchange the IP addresses in accordance with the requirements (see PHUB ScriptFormat.txt as guideline). DO NOT forget to save the text file after editing! Then closethe notepad.

7


8/15

8. First Setup shall only be executed if PHUB has factory default settings. Thisis done by selecting the Packet Hub NE, then Configuration SW Management APS Management PHUB maintenance window will appear and go toMaintenance tab, then select Restore to factory default settings click onExecute button Yes to warning window.

8


9/15

9. After status shown is success, then reboot the PHUB in the sameMaintenance tab by selecting Reset module click on Execute button Yesto warning window., PHUB will reboot and wait for a while until the Packet Hub NEcomes back online (you can also ping 192.168.1.1 to test connection)

10. Run First Setup by typing in 3 and it will prompt you to Continue?. ClickYes button. Then Choose IMA as WAN interface by typing in 2.

9


10/15

11. Select the number of E1 links belonging to the IMA group by typing in 1

12. Double-check the edited PHUB parameters in reference to the requirementsbefore continuing by clicking on the Yes button. (Note: If it needs changes thenprobably the edited notepad file was not saved properly and so you must repeat step7 then to step 10 onwards.)

10


11/15

13. PHUB scripting will run in the screen and take note of all the processesshould be Success. If any of the process lines showed Failed then repeatprocedure starting from step 8 onwards. It will prompt for Backup? click Yesbutton.

14. After the First Setup is done, change the IMA TX clock to ThroughTimed.(Note that this can only be done if the new Script file tcl037 is loaded for SNMPScripting. See separate procedure for updating old script files.) Type in 4warning window appears and prompts to continue? Click on Yes button typein 7 to select IMA_TX_clock menu then type in 3 to set ThroughTiming.

11


12/15

15. To check current IMA_TX_clock setup, type in 4. If it is ThroughTimed then

type in q q q.

16. DO NOT FORGET to save the previous configuration into backup file of thePHUB. This is done by selecting the Packet Hub NE, then Configuration SWManagement APS Management PHUB maintenance window will appear andgo to Maintenance tab, then select Save configuration into backup file clickon Execute button then after click on the Cancel button to close the window.

12


13/15

17. Next step is to configure the PHUB accordingly in reference to HW. Click onPacket Hub NE Configuration NE Configuration General NEParameters PHUB Configuration window appears. Set Target equipping toxDSL,4port to all ATM25#x that are up (which has physical connection from AL4to the PHUB). Others which has no connection, with oper status down, must beset to empty. click on Apply button click on Cancel button to closewindow.

18. Again, save changes done in the PHUB backup file, for PHUB as well as for allADSL cards by changing the PHUB ID in the PHUB Maintenance window then

clicking on Execute button every time. Click on Cancel button to close window.DONE!!!

13


14/15

DSL

ADSL: Asymmetrical Bitrate Digital Subscriber LineBDSL: Broadband Digital Subscriber LineCDSL: Consumer Digital Subscriber Line

CiDSL: Consumer installable Digital Subscriber LineEDSL: Enhanced Digital Subscriber LineHDSL: High bitrate Digital Subscriber LineIDSL: ISDN Digital Subscriber LineRADSL: Rate Adaptive Digital Subscriber LineSDSL: Single Pair Digital Subscriber LineUDSL: Universal Digital Subscriber Line

VDSL: Very high Bitrate Digital Subscriber Line

14


15/15

.

[email protected]

15

Documents

فحص خطوط fastlink ADSL