4
Summary technical issue on V2224G-OP No Technical issue from VFT V2224G.2.06.08-0006.x V2224G.2.08.01-0008.x V2224G-OP.2.09.01-0009.x Testing report 1 Mirror function to SIP packet √ (passed) 2 ● (Fail) 3 4 NMS for V2224G-OP 5 6 7 8 9 10 Talk later Talk later 11 Vlan translation function 12 LACP protocol with Cisco Router Switching time problem (up to 1 minute) 13 Hardware not supported 14 MVR function with IGMP V3's Specific multicast range pls remove Option82 if we use only IP DHCP Snooping How about the sample configuration to Policy and policer so that apply CIR, PIR to Vlan or interfaces… Can we enable/ disable PPPoE circuit tag to each port’s V2224G-OP ? PPPoE Enable is OK (add tag is OK) PPPoE Disable is not OK (keep tag is not OK) Could you flexible PPPoE circuit Tag same as Option82, pls ? (Example: %sysname_eth_0/0/0/0/%port:%S-Vlan.%C-Vlan) Change ARP padding to all zero value so that compatible to Huawei Quidway S8502 in VNPT Ha Tinh Default NOS support IP's Mgmt interface is 192.168.1.100/24 and protocol up, also. We would like to customize the command line on the V2224G-OP for the same CLI's formatting. Example: Inbound, outbound, untag when we use Dot1Q and QinQ in the same time. Rate Limit function work unproperly with "Ingress direction". Disable QinQ feature for unknown vlan, only enable QinQ for some specific vlan. ( before, only disable QinQ for some specific vlan by using vlan transalation function)

2. SWITCH_Summarize Technical Issue on V2224G-OP_Firmware Note_20130529

Embed Size (px)

Citation preview

Sheet1Summary technical issue on V2224G-OPNoTechnical issue from VFTV2224G.2.06.08-0006.xV2224G.2.08.01-0008.xV2224G-OP.2.09.01-0009.xTesting reportRemark1Mirror function to SIP packet (passed)VFT will be verify this funtion, again.2MVR function with IGMP V3's Specific multicast range (Fail)3pls remove Option82 if we use only IP DHCP Snooping4NMS for V2224G-OP 5How about the sample configuration to Policy and policer so that apply CIR, PIR to Vlan or interfaces6Can we enable/ disable PPPoE circuit tag to each ports V2224G-OP ?PPPoE Enable is OK (add tag is OK)PPPoE Disable is not OK (keep tag is not OK)VFT: * PPPoE snooping feature apply to one Port, only. -> mistake when config* When V2224G-OP work under "PPPoE Snooping" then all of services on eqipment occour stopped.We would like to verify this feature at your LAB that solve this problem, soon.

Dasan:* Check the stability of PPPoE Snooping function at our LAB.

7Could you flexible PPPoE circuit Tag same as Option82, pls ? (Example: %sysname_eth_0/0/0/0/%port:%S-Vlan.%C-Vlan)8Change ARP padding to all zero value so that compatible to Huawei Quidway S8502 in VNPT Ha Tinh9Default NOS support IP's Mgmt interface is 192.168.1.100/24 and protocol up, also.10We would like to customize the command line on the V2224G-OP for the same CLI's formatting. Example: Inbound, outbound, untag when we use Dot1Q and QinQ in the same time.Talk laterTalk later11Vlan translation function 12LACP protocol with Cisco Router Switching time problem (up to 1 minute)VFT:We already sent this FW version to some VNPT province that check it. LACP feature passed in VNPT Da Nang by cisco router 7606-s/7609-s. Let VFT check performance about 2 days.

Dasan (May292013): You can use distmode in bridge with this command : lacp aggregater # distmode 13Rate Limit function work unproperly with "Ingress direction".Hardware not supported14Disable QinQ feature for unknown vlan, only enable QinQ for some specific vlan.( before, only disable QinQ for some specific vlan by using vlan transalation function)Dasan (May292013): I think This is new requirment please give me detail information with document.15Config rate-limit for the total of services and guaranteed bandwith for each serviceDasan (May292013): I think This is new requirment please give me detail information with document.

Sheet2

Sheet3