Aircraft Maintenance Training and Experience Logbook for Aircraft

AITP-L02 Appendix IV - Aircraft Maintenance Practical Training/Experience Log Book - (Issue 2) Transport Malta is the Authority for Transport in Malta set up by ACT XV of 2009 Page 1

Civil Aviation Directorate Form TM/CAD/0053 Issue 1 - March 2010

� � �

�

CIVIL AVIATION DIRECTORATE - Airworthiness Inspectorate�� !"��#�� $% !��&&& ��#�� $% !�

Aircraft Maintenance Training and Experience Logbook for Aircraft Maintenance Trainees & Personnel

Introduction

This logbook has been compiled by the Transport Malta Civil Aviation Directorate to aid aircraft maintenance trainees and personnel record their practical training and experience to comply with Regulation (EC) No 2042/2003 Part-M, Part-145, Part-66 and Part-147 in terms of requirements for:

• BASIC PRACTICAL TRAINING

• TYPE TRAINING PRACTICAL ELEMENT

• AIRCRAFT MAINTENANCE APPRENTICESHIPS

• MAINTENANCE EXPERIENCE FOR CERTIFYING AND SUPPORTING STAFF

Section 2 - Basic Skills Section is aimed at the trainee undergoing Basic Training for Part-66 Category A, B1 and B2 as well as aircraft maintenance apprenticeships. Section 3 - Maintenance Experience Section is aimed at trainees undergoing basic training and aircraft maintenance personnel undergoing practical element of type training and continuation of maintenance experience.

The practical training leading to a Part-66 AML or Part-147 Recognition Certificate can be conducted at an appropriately approved aircraft maintenance training organisation or an approved maintenance organisation.

Section 3 – Personal Details contains: Personal Data, Names of assessors and supervisors, Aircraft Type and Registration Marks, ATA Chapters, Practical Training/Tasks.

The trainee shall record the training carried out and the assessor shall verify this information and make the necessary remarks regarding the competency and level achieved by the trainee. The trainee and assessor shall ensure that he/she has obtained competency in all the relevant Basic Skills listed in this logbook during his/her training period. All entries shall be made in ink. The nature of the involvement in task or intervention should be specified (execution, assistance, control, supervision). A new entry would be sufficient per day to count for the work experience time interval requirement in accordance with Part-66.

The assessor shall be nominated by the maintenance training organisation or the maintenance organisation. When logging maintenance tasks carried out on in-service aircraft, the supervisor can sign for the task and assessor endorses the experience. The Assessor needs to make sure he carries out an evaluation of the work carried out and progress by the trainee.



Section 1

PERSONAL DETAILS

Name of Trainee: Date of Birth:

Signature: Address:

Name of Training Organisation:

Course Title: Licence No (if applicable):

Date of Course Commencement: Date of course completion:

Assessors: Remarks from Assessor:

Miscellaneous Information (type courses/ training/ employment) Photo



Section 2

BASIC SKILLS To be Accomplished during Basic Training



Basic Skills Category Date (dd/mm/yy)

Signature and Stamp of Assessor

Health and Safety Awareness A, B1, B2

Hangar Practices Familiarisation A, B1, B2

Location of station numbers and other reference systems A, B1, B2

Use of Hand tools A, B1

Use of Power Tools B1

Identification of Materials A, B1, B2

Use of Measuring Equipment (Depth Gauge, micrometerFeeler/slip gauges, go, no-go gauges)

A, B1

Remove/install Thread Insert A, B1

Drilling and Tapping (Fe, Al etc) B1

Reaming B1

Use of Maintenance Data (IPC, AMM, CMM, SRM, effectivity) A, B1, B2

Identification of Corrosion B1

Countersinking B1

Familiarisation and use of standard tools A, B1

Name: Signature:




Remarks/Comments Signature of Assessor

Identification of standards and specs of nuts, bolts, washers, split-pins, rivets …

B1

Competence in Wire locking of components and turnbuckles A, B1, B2

Wire/ Cable Looming B1, B2

Identification of cables B1, B2

Familiarisation and Use of Cable Stripping devices B1, B2

Familiarisation with Crimping Tools commonly used B1, B2

Crimping A, B1, B2

Soldering B1, B2

Use of Heat Gun B1, B2

Splicing Techinques B1, B2

Use of Cable inserts B1, B2

Familiarisation and use of Multimeters A, B1, B2

Accomplishment of Resistance Checks B1, B2

Accomplishment of Continuity Checks B1, B2

Accomplishment of Bonding Checks B1, B2

Name: Signature:




Remarks/Comments Signature of Assessor

Implementation of ESDS procedures A, B1, B2

Basic Skills in Sheetmetal (cutting, bending, deburring…) A, B1

Calculation of Bend Radii B1

Achieve an acceptable level of Riveting experience B1

Installation of oversize rivets B1

Fasteners Removal using dedicated tools B1

Corrosion Treatment of Al in accordance with SRM methods B1

Accomplish a doubler repair B1

Testing and repair of composite material B1

Dye Penetrant / Flourescent Penetrant Inspection B1

Removal and Installation of flexible hoses B1

Removal and Installation of rigid pipes B1

Familiarisation with Fuel Tank Safety A, B1, B2

Aircraft Towing and Taxying B1, B2

Name: Signature:



Section 3

MAINTENANCE EXPERIENCE Accomplished on In-service aircraft

Applicable to Basic Training /Type Training Practical Element

Task Codes:

OT – Operational Test SGH – Servicing Ground Handling LOC - Location RIA - Removal Installation Actuation

Note: Last two pages are blank. These pages can be used and reproduced for the recording of the maintenance experience not covered in the scope of the tasks listed in this section.



Aircraft Regn. Type, Engine Type

ATA/ SYSTEM

TASK ACCOMPLISHMENT AND COMPETENCY Category Date (dd/mm/yy)

Signature and Stamp of Supervisor

07-00-00 LIFTING & SHORING

Main jacking points / discuss jacking procedure and safety procedure. (LOC)

A, B1

Aircraft Levelling B1

Aircraft Weighing B1

08-00-00 LEVELLING & WEIGHING

Towing Points / Limitation of Steering Angle (LOC) A/B1/B2

Assist in aircraft towing/taxiing A/B1/B2

Engine / airframe blanking (SGH) A/B1/B2

Landing gear locking pins (SGH) A/B1/B2

09-00-00 TOWING & TAXING

Assist in aircraft docking B1/B2

Automatic refuel/defuel procedures (SGH) B1

Hydraulic fluid servicing (SGH) A/B1


ATA/ SYSTEM



Landing gear fluid servicing (SGH) A/B1



Electrical power servicing (SGH) A/B1

Hydraulic gas servicing (SGH) A/B1

Landing gear gas servicing (SGH) A/B1

Potable water servicing (SGH) A/B1

Lavatory servicing (SGH) A/B1

10-00-00 ��

Ice & rain protection servicing (SGH) A/B1

Flight control lubrication (SGH) A/B1

Landing gear lubrication (SGH) A/B1

Replace Combustion Heater B1

12-00-00 SERVICING

Check Placarding and Markings A, B1, B2


ATA/ SYSTEM



21-00-00 AIR CONDITIONING

Clean Outflow Valves B1

Safety valves (RIA) B1



Flow control valve (RIA) B1

Cabin temperature sensor (LOC) B1

Assist in Pressurisation Test B1

Assist in Cabin Leak Rate test B1

Air Cycle Unit (RIA) B1

Pressurisation Controller (RIA) B1

22-00-00 AUTO FLIGHT

Yaw Damper (OT) B2

Autopilot (OT) B2

Mach Trim (OT) B2


ATA/ SYSTEM



Flight Director (OT) B2

Auto Throttle (OT) B2

Autoland (OT) B2

Flight Management System (OT) B2

23-00-00 COMMUNICATION



VSWR Antennae Checks B2

Antennae (RIA) B2

24-00-00 ELECTRICAL POWER SYSTEM

IDG oil level and differential pressure indicator

check

A/B1

IDG oil scavenge filter element B1

IDG/CSD (RIA) B1

IDG servicing A/B1


ATA/ SYSTEM



Charge lead/acid battery B1/B2

Charge Ni-Cad battery B1/B2

Deep cycle Ni-cad battery B1/B2

Main/emergency battery (RIA) B1/B2

Battery (RIA) B1/B2

25-00-00 CABIN EQUIPMENT/FURNISHINGS

Passenger seats (RIA) A/B1

Ceiling panels, sidewall (RIA) A/B1



Cabin attendants seats (RIA) A/B1

Emergency Equipment Checks A/B1/B2

Carpets (RIA) A/B1

Fire Bottles (RIA) A/B1

Seat Belts Checks A/B1


ATA/ SYSTEM



26-00-00 FIRE/SMOKE PROTECTION

Engine Fire Detection Test (OT) B1

Squibs (RIA) B1

Fire wire inspection B1

27-00-00 FLIGHT CONTROL SYSTEM

Adjustment/rigging of rudder mechanical linkage (RIA)

B1

Rigging of the THS Controls (RIA) B1

Replacement of a flight control surface B1

Installation/Rigging of control cables B1

Function Test Flight Control System B1



Flight Control Rigging B1

28-00-00 AIRCRAFT FUEL SYSTEM

Fuel system control/indications in cockpit (LOC) B1


ATA/ SYSTEM



Fuel tank venting (LOC) B1

Water drain system (LOC) B1

Fuel quantity indicating system (OT) B1

Fuel transfer from tank to tank (OT) B1

Fuel crossfeed valve (OT) B1

Replace fuel boost pump B1

29-00-00 HYDRAULIC POWER SYSTEM

Hydraulic system (OT) B1

Hydraulic System component (RIA) B1

Engine Driven Pump (RIA) B1

Electric Motor Driven Pump (RIA) B1

Troubleshoot faulty system B1



Filters check B1


ATA/ SYSTEM



30-00-00 ICE/RAIN DETECTION/PROTECTION SYSTEM

Wing anti-ice valve (RIA) B1

Engine anti-ice valve (RIA) B1

Inspection/Repair of pneumatic de-icing boots B1

Pump, timer (RIA) B1

31-00-00 INDEPENDENT INSTRUMENT

Familiarisation with ECAM/EFIS/EICAS B1/B2

Familiarisation with ESDS procedures B1/B2

FDR data retrieval B2

BITE test of recorders B2

Familiarisation with instrument panel B1/B2

32-00-00 LANDING GEAR

Wheel build-up B1




ATA/ SYSTEM



Nose/Main wheel (RIA) B1

Shimmy damper (RIA) B1

Shock strut seals (RIA) B1

Brake control valve (RIA) B1

System controls and Indications (LOC) B1

Brake unit (RIA) A/B1

Brake system bleeding (RIA) B1

Park Brake operation (RIA) B1

Assist in landing gear retraction test B1

Anti-skid Unit (OT) B1

Nosewheel steering rigging B1

Bungees (RIA) B1

33-00-00 AIRCRAFT LIGHTING SYSTEM


ATA/ SYSTEM



Exterior and Interior Lights replacement A/B1/B2



Landing Light (RIA) A/B1/B2

34-00-00 NAVIGATION DATA SYSTEM

TCAS System (OT) B2

IR alignment procedure (SGH) B2

IRS start procedure B2

ILS/VOR Test B2

Gyroscopic Instruments (RIA) (OT) B2

Flight director (OT) B2

Radio altimeter Functional Testing B2

DME Functional testing B2

ADF Functional testing B2

Weather Radar (RIA) (OT) B2


ATA/ SYSTEM



Airspeed Indicator (RIA) B2

Pitot-Static Calibration B1/B2

Compass Check B2



Familiarisation with RVSM Requirements B2

GPS (OT) B2

GPWS, TAWS (OT) B2

35-00-00 OXYGEN SYSTEM

Crew oxygen storage cylinder (RIA) B1

36-00-00 PNEUMATIC SYSTEN

IP bleed check valve (RIA) B1

HP bleed valve (RIA) B1

Filters (RIA) B1


ATA/ SYSTEM



37-00-00

Vacuum pump (RIA) B1

Filters (RIA) B1

38-00-00 WATER/WASTE SYSTEM

Water/Toilet Pumps (RIA) B1

System Troubleshooting B1



45-00-00 CENTRAL MAINTENANCE COMPUTER

Download data B1, B2

49-00-00 AUXILIARY POWER UNIT/SYSTEM

APU (RIA) B1

APU Servicing B1

52-00-00 AIRCRAFT DOORS SECTION

Opening and closing of passenger and crew doors B1/B2


ATA/ SYSTEM



Special precautions before work on pax/crew doors (RIA)

B1/B2

Escape slide disarming when opening door from outside (OT)

B1/B2

Emergency escape slide (RIA) B1

Cargo door actuator (RIA) B1

Door warning system (OT) B1/B2

53-00-00 FUSELAGE STRUCTURE

Bulkhead structural Inspection B1



54-00-00 PYLON STRUCTURE SYSTEM

56-00-00 WINDOW/WINDSHIELD

Cockpit windshield (RIA) B1

Window (RIA) B1

57-00-00 WING STRUCTURE

General Condition Inspections B1


ATA/ SYSTEM



61-00-00 PROPELLER & CONTROL

Propeller (RIA) B1

Propeller balancing B1

Blade Damage dressing/evaluation B1

Propeller Track Check B1

Governor (RIA) B1

62-00-00 MAIN ROTOR

Rotor Assembly B1

Blades (RIA) B1.3



Damper Assembly (RIA) B1.3

Check Track B1.3

Check Static Balance B1.3

Check Dynamic Balance B1.3

Aircraft Regn.

Type, Engine TypeATA/

SYSTEMTASK ACCOMPLISHMENT AND

COMPETENCY

Category Date (dd/mm/yy)


Troubleshooting B1.3

63-00-00 MAIN ROTOR DRIVE

Main Gearbox (RIA) B1.3

Check Gearbox Chip Detectors B1.3

Drive Coupling B1.3

64-00-00 TAIL ROTOR

Rotor Assembly (RIA) B1.3

Blades (RIA) B1.3

Troubleshooting B1.3



67-00-00 ROTORCRAFT FLIGHT CONTROL

Replace Universal Joints B1.3

Collective System Rigging B1.3


ATA/ SYSTEM



Install Swash Plate B1.3

Adjust Pitch Links B1.3

71-00-00 POWERPLANT

Opening and closing of engine cowlings (RIA) B1

Assist in Engine Change B1

72-00-00 TURBINE/TURBOPROP ENGINE

Borescopic Inspection B1

FOD inspection (LOC) B1

Assist to Engine Run B1

Compressor Wash B1

Hot Section Inspection B1



Fan Blades (RIA) B1


ATA/ SYSTEM



73-00-00 ENGINE FUEL & CONTROL

Fuel filter (RIA) B1

MEC/Fuel Control Unit (RIA) B1

Fuel Pump (RIA) B1.2

Carburettor (RIA) B1.2

Injector (RIA) B1.2

Carburettor / injector Setting B1.2

Clean Injector Nozzles B1.2

74-00-00 ENGINE IGNITION SYSTEM

Igniter plug (RIA) B1

Spark Plugs (RIA) B1.2

Timing of Magnetos B1.2

Check H.T leads B1, B1.2




ATA/ SYSTEM



Leads (RIA) B1.2

Test Spark Plugs B1.2

Magneto (RIA) B1.2

Troubleshooting B1, B1.2

75-00-00 ENGINE BLEED AIR SYSTEM

76-00-00 ENGINE CONTROL SYSTEM

Throttle control system rigging and adjustment (RIA)

B1

RPM control rigging B1

Propeller synchronization system check B1

77-00-00 ENGINE INDICATING SYSTEM

Engine Parameters Indication Familiarisation B1

Engine Parameters Instrumentation Checks B1


ATA/ SYSTEM



Chip detectors (RIA) B1



Oil filters (RIA) B1

Oil quantity indication (RIA) B1

78-00-00 ENGINE EXHAUST

Thrust reverser (RIA) B1

79-00-00 ENGINE OIL SYSTEM

Oil Tank (RIA) B1

Oil Change (RIA) B1

Oil Cooler (RIA) B1

80-00-00 STARTER

Starting Valve (RIA) B1

Starter motor chip detector (RIA) B1


ATA/ SYSTEM



Engine Starting Sequence Familiarisation B1

Starting Relay (RIA) B1

Start APU B1/B2



81-00-00 TURBOCHARGING SYSTEM

PRT (RIA) B1.2

Turbo-blower (RIA) B1.2

Heat shields (RIA) B1.2

Waste gate (RIA) B1.2

Density Controller Adjustment B1.2

85-00-00 RECIPROCATING ENGINE

Piston Engine Compression Tests B1.2

Check Tappet Clearance B1.2

Check Engine mounts and Attachment points B1.2


ATA/ SYSTEM



Check Cooling Partitions B1.2

Check air intake system B1.2




ATA/ SYSTEM






ATA/ SYSTEM






ATA/ SYSTEM






ATA/ SYSTEM






ATA/ SYSTEM



Documents

Aircraft Maintenance Training and Experience Logbook for Aircraft