PC 1055 JAtlas Copco Powercrusher

Jaw crusher Capacity* – Up to 200 t/h

www.atlascopco.com

Features and technical information for PC 1055 JFor further information, please contact your local Atlas Copco Customer Center.

Quick facts

The Atlas Copco Powercrusher jaw crushers have been designed to operate in the most rugged environments - and incorporate the unique “Quattro Movement”. This “Quattro Movement” is made possible by an up-thrust toggle plate position. This causes a figure 8 motion in the moving jaw, which increases the feeding capacity and also producesa post-crush at the crusher outlet. The PC 1055 J gives you:

• Less blockages• More consistent wearing over the entire jaw faces• High percentage of less flaky material• Higher capacity• Excellent transport dimensions for optimized mobility

98

51 2

753

01c

201

1-02

-04

Öre

bro

, Sw

eden

Leg

al N

oti

ce ©

Co

pyr

igh

t 20

10, A

tlas

Co

pco

Ro

ck D

rills

AB

, Öre

bro

, Sw

eden

. All

pro

du

ct n

ames

in t

his

pu

blic

atio

n ar

e tr

adem

arks

of

Atl

as C

op

co. A

ny

un

auth

ori

zed

use

or

cop

yin

g

of

the

con

ten

ts o

r an

y p

art

ther

eof

is p

roh

ibit

ed.

Illu

stra

tio

ns

and

ph

oto

s m

ay s

ho

w e

qu

ipm

ent

wit

h o

pti

on

al e

xtr

as.

No

war

ran

ty i

s m

ade

reg

ard

ing

spec

ifica

tio

ns

or

oth

erw

ise.

S

pec

ifica

tio

ns

and

equ

ipm

ent a

re s

ub

ject

to c

han

ge

wit

ho

ut n

oti

ce. C

on

sult

yo

ur

Atl

as C

op

co C

ust

om

er C

ente

r fo

r sp

ecifi

c in

form

atio

n.

Up-thrust toggle position (Quattro movement)

Sanpro plates under main conveyor belt at outlet to absorb

impact

Large distance between

crusher outlet and conveyor

belt (required for recycling)

Fixed hydraulic tubes

Hydraulically foldable side

conveyor Folding main conveyor

Hydraulically adjustable vibrating hopper

Hardox hoppers. Feeding with loader

possible

Large flywheel provide

unparalleled momentum

30% bigger hydraulic tank

CAT C7 T3drive unit

Permanent magnetic separator

19 mm (¾") steel reinforced

rip stop bult

Technical data

Crusher boxInlet opening 1 000 x 550 mmGap width 50 - 130 mm Jaw Flywheel 1 360 mm Crusher revolution 330 (max. rpm)

FeedhopperCharging volume approximately 3.9 m³Charging length 2 800 mm Charging width 2 350 mm Charging height 3 500 mm

Vibrating chute with pre-screeningLength 3 400 mmWidth 1 000 mm

Main conveyor beltBelt width 1 000 mm Discharge height 2 900 mm

Side conveyor beltBelt width 500 mm Discharge height 1 910 mm

Crawler unitTrack chain width 330 mm

Permanent magnetic separatorBelt width 750 mm

*Capacity - Crusher production depends on gap settings,

material, infeed size and feed rate.

Unit type Jaw crusherInlet opening 1 000 x 550 mmTotal weight 34 000 kgTransport dimensions (L) 11 500 x (W) 2 650 x (H) 3 350Crushing capacity Up to 200 t/hEngine power 187 kW (252 HP)