Upload
torillaz
View
219
Download
0
Embed Size (px)
Citation preview
8/11/2019 BA015B15
1/26
8/11/2019 BA015B15
2/26
1.The lcd meter is apply forDC 12V.2.For installation, please follow the steps described in manual. Any
damage caused by wrong installation shall be imputed to the users.3.Don't break or modify the wire terminal. To avoid the short circuit, please
don't pull the wire when installing.4.Do not disassemble or change any parts excluding the manual
description.5.The interior examination or maintenance should be executed by our professionals.
MARK MEANING:
WARNING!CAUTION!
You could get the installation details from the information behind the mark.
Some processes must be followed to avoid the affection caused by wrong installation.
Some processes must be followed to avoid damages to yourself or the public.
Some processes must be followed to avoid the damage to the vehicle.
Press the buttonone time
Press down the buttonfor 3 seconds
1-1
Content
Accessory
Thank you for purchasingKOSO RX2N GP style meter, before operating theunit, please read the instruction thoroughly and retain it for the future
reference.
Notice
Option accessory1-2
2-1
Installation instructions2-2
Wiring installation instructions
3-1
3-2
3-33-4
Overview
The button function instruction
The screen switch instruction
Auto-checking screen
4-1
5-1
4-2
5-2
The power test screen instruction
4-3
5-3
5-6
5-7
5-8
5-9
5-10
5-11
5-12
5-13
6
4-4
5-4
Speeding warning light setting
5-5
Tire circumference and sensor point setting
The clock setting
The target speed timer / target distance time
The fuel gauge resistance and insufficient fu
setting
6-1
6-26-3
7
5
Trouble shooting
The top speed testTarget distance timer test
Target speed timer test
We recommend that you finish the relative setting bassure the operation of meter.
The RPM shift light setting
Attachment
Attachment
Attachment
Attachment
Meter size
Function, setting instruction
Select button function instruction
Adjust button function instruction
The setting screen instruction
Over heat warning light (Water temperature)
Over heat warning light (Oil temperature) se
RPM input pulse & signal impulse setting
The perpetual calendar setting
The backlight brightness setting
The real odometer record setting
The displayed odometer setting
8/11/2019 BA015B15
3/26
3-1Off
Check 1
Check 2
Check 3
On
1 0 0 7
Auto-checking screen
It will enter the setting screen automatically when the first time you start it.
Check 4
Check 5
Check 6
Check 7
Check 8
3-2
26.5 mm 32.5 mm 38.42 mm
135.7 mm
26.5
mm
23.2mm
Meter size
8/11/2019 BA015B15
4/26
3-3
Fuel meterDisplay range: 10 levels.Setting range: 100 , 510switch, no display.
Fuel warningSetting range: 10~50 %Setting unit: 10 %
>Regarding the setting, ple
Level thermometer(Water & oil temperature)
oDisplay range: 20~120 C
10 levels.Display unit: Each level re
o o10 C (50 F)
Tachometer (10,000 RPM)Display range: 0~10,000 RPM.Display unit: 250 RPM.
Tachometer (20,000 RPM)Display range: 0~20,000 RPM.Display unit: 500 RPM.
SpeedometerDisplay range: 0~360km/h (0~225 MPH)
Display unit: km/h &MPH for alternative.
>Regarding the setting,please check4-4.
Odo meter
Display range:0~99999.9 km (mile)
Display unit: 0.1 km (mile).
Trip meter A.BDisplay range: 0~999.9 km(mile)
Display unit: 0.1 km (mile).
, resetautomatically after 99999.9 km.
, reset automatically after
999.9 km.
Indicators l ights
Turn signal light (Green)
Neutral light (Green)High beam light (Blue)
EOBD light (Amber)Engine oil pressure light (Red)
Speeding warning light
Setting range: 30~360 km/h(20~225 MPH).Setting unit: 1 km/h (MPH).
>Regarding the setting,please check 5-1.
O(Water & oil temperature)
Setting range: 6o(140~482 F) o
Setting unit: ( F)>Regarding the setting, please
check5-3.5-4.
ver heat warning light
o0~250 C
.o
1 C .
Clock24H
Digital(Water & oil temperature)
oDisplay range: 0~250 Co
(32~482 F)o o
Display unit: 0.1 C ( F)
thermometer
The max RPM recall indicator lightThe indicator light will moveaccording to the current RPM.The max RPM indicator light willshow you the max RPM you reachand light on for 3 seconds.
Tachometer (10,000 RPM)Display unit: 250 RPM.
Tachometer (20,000 RPM)Display unit: 500 RPM.
The RPM shift light (10,000 RPM)Setting range: 1,000~10,000 RPM.Setting unit: 100 RPM.
The RPM shift light (20,000 RPM)Setting range: 1,000~20,000 RPM.Setting unit: 100 RPM.
Overview
Pre-Shift lightSetting range
before the shiSetting unit: 1
>Regarding the check 5-2.
Max.Thetheanau
8/11/2019 BA015B15
5/26
Display internal
Trip meter A/B
Odometer
Top speed record
8/11/2019 BA015B15
6/26
4-24-1Select button
Select & Adjust X 3 seconds
Select button X 3 seconds
Adjust button
Adjust button X 3 seconds
The button function instruction
1.In main screen, press the Select buttonto choose the display of clock,water temperature or oil temperature.
2.In power test screen, press the Select buttonto choose the function you
want to use.3.In setting screen, press the Select button to choose the function you want
to set.
1.When the temperature Is In the main screen, you couldpress down the "Select" button for 3 seconds to switch
the temperature unit.2.In power test screen, press down the Selectbuttonfor 3 seconds to back to the main screen.
3.In setting screen, press down the Select button for 3 seconds to back to the main screen.
In main screen, press down theAdjust buttonfor 3 seconds to reset the tripA, trip B, or the Max. Record.
In main screen, press down the Select & Adjustbuttonsat the same time for 3 seconds to enterthe setting screen.
CAUTION!
The screen switch instruction
In the setting screen, press dbuttonfor 3 seconds to back
In main screen, press down tbuttonat the same time for the setting screen.
In main screen, press the Seone time to enter the power
In power test screen, press dbuttonfor 3 seconds to back
In any screen, you couldprbuttonsfor 3 seconds to ba
Press down the Adjust buttonIn setting screen, to add the setting value fast.
For safety reason - you could adjust the setting or operatethe function only when the bike is stop.
1.In main screen, press theAdjust buttonto choose the display of odometer, trip A, trip B or the Max. record.2.In power test screen, press theAdjust buttonto reset the record, stop the
testing, or restart the test.3.In setting screen, press theAdjust buttonto make the setting. If you keeppressing down theAdjust buttonthe setting number will increase fast.
Select &AdjustX3 S
SelectX3 S
Select &Adjust
one time
SelectX3 S
8/11/2019 BA015B15
7/26
4-4In main screen, press the Select buttonto choosethe function combination you want to display onthe screen.The alternative combination is as the circle we list:
clock+fuel gauge water temperature+fuelgauge water temperature+oil temperaturelevel gauge oil temperature+watertemperature level gauge clock+fuel gauge.
Select button function instruction Adjust button function instruction
If you don't install the fuel wiring, thefuel gauge will not display.
4-3
Press down theAdjust butto reset the Max.record.
In ODO function, press thetime to switch to the trip A
In trip A screen, press thetime to switch to the trip
In trip B screen, press thetime to switch to the Max
In Max. record screen, prone time to switch to the
When the temperature Is In the main screen, you could press down the "Select" button for 3 seconds to switch the temperature unit.
Press down theAdjust but
to reset the trip A.
Press down theAdjust but
to reset the trip B.
Press the Select buttonon
oil temperature record.
8/11/2019 BA015B15
8/26
The setting screen instruction
If you enter the setting screen for 30 seconds and don't press thebutton, it will back to the main screen automatically.
In main screen, press down the Select&Adjustbuttonat the same time for 3 seconds to enterthe setting screen.The setting screen is in order as the following
drawing, please use the setting order for yourreference when you want to set the meter.
5
Speeding warning light setting
The RPM shift light setting Over heat warning light(Wate r temperatu re) se tting
Over heat warning light(Oil temperature) sett ing
The target speed timer / targetdistance timer setting
Tire circumference and sensorpoint setti ng
The perpetual calendar settingThe backlight brightness settingThe real odometer record settingThe displayed odometer setting
8/11/2019 BA015B15
9/26
S
P.S.
5-1 Speeding warning light setting
In a 1screen, press the Select buttonto enterthe speeding warning light setting screen.
EX. Now the speeding warning light setting is60 km/h.
EX. The speeding warning light you want toset is 65 km/h.
Press the Select buttonto move to the digityou want to set.
The speeding light willlight on when the speed reaches
your speeding warning setting.
The speeding warning light settingrange: 30~360km/h (20~225 MPH).
Setting unit: 1 km/h (MPH).
Press theAdjust buttonto choose the settingvalue.
Press theAdjust buttonto setting screens.
Press the Select buttontoscreen.
EX. Now the setting is chato 65 km/h.
Now the speeding warning light and thesetting value is flashing!
When you leave thisis finished.
If you just want to make this fpress down the Select buttonthe main screen.
The setting unit will change together with theunit setting (4-4).
Next page
8/11/2019 BA015B15
10/26
S
P.S.The yellow color pre-shift lightwill light on according to the
shift light setting number.
S
P.S.
5-2 The RPM shift light setting
Now the pre-light and theflashing!Now the shift light and the setting value is
flashing!
The red color shift light willlight on according to theshift light setting number.
In a 2screen, press the Select buttonto enterthe RPM shift light setting screen.
EX. Now the RPM shift light setting is 7,000 RPM.
EX. The you want to set is.
RPM shift light12,000 RPM
Press theAdjust buttonto choose the settingvalue.
Press the Select buttonto enter the pre-shiftlight setting.
EX. Now the s setting is changedfrom 7,000 RPM to 12,000 RPM.
hift light
EX.
The equation is as followinThe shift light setting value
pre-shift light setting valueRPM you want the pre-shifThe setting value of pre-sh
It means that you should ssetting as 1,500.
You want the pre-shift 10,500 RPM
Press theAdjust buttonto value.
The setting range: -Setting unit: 100 RPThe setting range: 1,000~10,000 /
20,000 RPM.
Setting unit: 100 RPM.
Next pageNext page
Press the Select buttonto screen.
EX. Now The pre-shift lightfrom 500 RPM to 1,500 RP
When you leave thisis finished.
8/11/2019 BA015B15
11/26
5-2 The RPM shift light setting
Press theAdjust buttonto select the othersetting screens.
If you just want to make this function setting, you couldpress down the Select buttonfor 3 seconds to back tothe main screen.
5-3 Over heat warning light (Water tempera
S
P.S.The over heat warning light
(Water temperature) will flashwhen the temperature reached
your setting.
In a 3screen, press the Sethe over heat warning lighsetting screen.
EX. Now the over heat war
temperature) setting is 100
Now the water temperatusetting value are flashing
The over heat warnirange: 60~
Setting unit:
o250 C (1o o1 C ( F)
The setting unit will changunit setting (4-4).
EX. You want to set the ovelight (Water temperature)
Press the Select buttonto myou want to set.
Press theAdjust buttonto cvalue.
Next page
8/11/2019 BA015B15
12/26
Press theAdjust buttonto select the othersetting screens.
Press the Select buttonto return to a 3settingscreen.
EX. Now the setting is changed from 10to 102 .
o0.0 Co.0 C
When you leave this screen, the settingis finished.
If you just want to make this function setting, you couldpress down the Select buttonfor 3 seconds to back tothe main screen.
5-3 Over heat warning light (Water temperature) setting 5-4 Over heat warning light (Oil temperatu
S
P.S.The over heat warning light
(Oil temperature) will flashwhen the temperature reached
your setting.
In a 4screen, press the Sethe over heat warning lighsetting screen.
EX. Now the over heat war
temperature) setting is 100
Now the water temperatsetting value are flashing
The over heat warnirange: 60~
Setting unit:
o250 C (1o o1 C ( F)
EX. You want to set the ovelight (Oil temperature) at 1
Press the Select buttonto myou want to set.
Press theAdjust buttonto cvalue.
The setting unit will changunit setting (4-4).
Next page
8/11/2019 BA015B15
13/26
Press theAdjust buttonto select the othersetting screens.
Press the Select buttonto return to a 4settingscreen.
EX. Now the setting is changed from 10to 102 .
o0.0 Co.0 C
When you leave this screen, the settingis finished.
If you just want to make this function setting, you couldpress down the Select buttonfor 3 seconds to back tothe main screen.
5-4 Over heat warning light (Oil temperature) setting The target speed timer / target distance timer se
Now the target speed val
The target speed tim30~360 km/h (20~2Setting unit: 5 km/h
Next page
In a 5screen, press the Sethe target speed timer antimer setting screen.
EX. Now the target speed
km/h and the target distan1/32 mile (50 M).
Press the Select buttonto edistance timer setting scre
EX. Now the target speed from 0~50 km/h to 0~110
EX. You want to set the targsetting at 0~110 km/h.
Press theAdjust buttonto cvalue.
EX. You want to set the targsetting at 2/32 mile (100 M
Press theAdjust buttonto cvalue.
5-5
8/11/2019 BA015B15
14/26
Now the target distance value is f lashing!
The target distance timer setting range:1/32~20/32 mile (50~1,000 M).Setting unit: 1/32 mile (50 M).
Press theAdjust buttonto select the othersetting screens.
Press the Select buttonto return to a 5settingscreen.
EX. Now the target distance timer setting ischanged from 1/32 mile (50 M) to 2/32 mile
(100 M).
When you leave this screen, the settingis finished.
If you just want to make this function setting, you couldpress down the Select buttonfor 3 seconds to back tothe main screen.
The target speed timer / target distance timer setting5-5 5-6 Tire circumference and sensor point se
CAUTION!Please measure the tire cirThe speed displayed on thaffected by the setting, plesetting number is correct bthe setting.
In a 6screen, press the Sethe tire circumference anscreen.
EX. Now the tire circumfer
mm, and the sensor point
EX. You want to set the circ1,300 mm.
Press the Select buttonto myou want to set.
Now the setting value is fl
The tire circumferen300~2,500 mm.
Setting unit: 1 mm.
S
P.S.You could define the valve asthe starting point and theterminal point to measure the
wheel circumference with ameasuring tape.
Next page
8/11/2019 BA015B15
15/26
EX. The sensor pointyou want to set is 6.Press the Select buttonto move to the digityou want to set.
Press theAdjust buttonto choose the settingvalue.
Press the Select buttonto enter the sensorpoint setting screen.EX. Now the circumference setting is changedfrom 1,000 mm to 1,300 mm.
Now the sensor point setting value is flashing!
The sensor point setting range: 1~60points.
Next page
Press theAdjust buttonto choose the settingvalue.
5-6 Tire circumference and sensor point setting
Press theAdjust buttonto setting screens.
Press the Select buttontoscreen.
EX. Now the sensor point sfrom 1 to 6.
When you leave thisis finished.
If you just want to make this fpress down the Select buttonthe main screen.
5 7 RPM i t l & i l i l tti
8/11/2019 BA015B15
16/26
5-7
The RPM input pulse setting range is :0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6.
In a 7screen, press the Select buttonto enterthe RPM input pulse setting screen.
EX. Now the RPM input pulse setting is 1 (4 Stroke,2 piston) and the signal impulse setting is Hi
(The posit ive impulse).
EX. You want to set the RPM input pulse at 2(4 Stroke, 4 piston) .Press theAdjust buttonto choose the settingvalue.
EX. The signal impulse you(The negative impulse) .Press theAdjust buttonto cvalue.
The corresponding
stroke and pistons number.
The corresponding RPM signal
number per i gnition.
2 RPM signals per 1 ignition.
2 RPM signals per 3 ignition.
2 RPM signals per 5 ignition.
2 RPM signals per 10 ignition.
1 RPM signal per 1 ignition.
1 RPM signal per 2 ignition.
1 RPM signal per 3 ignition.1 RPM signal per 4 ignition.
1 RPM signal per 6 ignition.
The setting
value
0.5
11.5
2
32.5
45
6
2C-1P
2C-2P
2C-3P
2C-4P
2C-6P
4C-1P
4C-4P
4C-6P
4C-5P
4C-8P
4C-10P
4C-12P
4C-2P
4C-3P
Most of the 4-cycle bikes withone single piston are igniting every 360 degreeonce, so the setting should be the same as the
bike with 2-cycle and one piston engine.
CAUTION!
Press the Select buttonto eimpulse setting screen.
EX. Now the RPM input pulfrom 1 (4 Stroke, 2 piston)
4 piston).
If the tachometer casignal (No RPM is disscreen), you could csetting, and check i
The impulse setting r(The positive impulsenegative impulse).
Press the Select buttonto rscreen.
EX. Now the signal impulsechanged from Hi P to Lo.
When you leave this is finished.
Now the setting number is flashing!
Next page
RPM input pulse & signal impulse setting
Press theAdjust buttonto ssetting screens.
If you just want to make this fupress down the Select buttonthe main screen.
5 8 Th f l i t d i ffi i t f l i tti
8/11/2019 BA015B15
17/26
5-8 The fuel gauge resistance and insufficient fuel warning setting
Now the resistance setting value is flashing!
The fuel gauge resistance setting range: 100 , 510 , fuel switch.The switch setting is for the fuel switchonly, can't be used for the fuel levelsensor.
If you don't install the fuel wiring, thefuel gauge will not display.
In a 8screen, press the Select buttonto enterthe fuel gauge resistance and insufficient fuelwarning setting screen.
EX. Now the fuel gauge resistance setting is
100 and the insufficient fuel warning settingis 30 %.
EX.0
You want to change the fuel resistancesetting to 51 .
Press theAdjust buttonto choose the settingvalue.
S
P.S.Usually the fuel gauge resistance is 100 on YAMAHAsystem, and 510 on HONDA system.The insufficient fuel warning setting: When the fuel is
less than your setting, the fuel level gauge will flash towarn you.
Press the Select buttonto efuel warning setting screen
EX. Now the fuel gauge se100 to 510 .
EX. You want to set the insuwarning setting at 20 %.
Press theAdjust buttonto cvalue.
Now the insufficient settin
The insufficient fuel wrange: 10~50 %. Se
Press the Select buttonto rscreen.
EX. Now the setting is chan20 %.
When you leave this is finished.
Press theAdjust buttonto ssetting screens.
Next page
If you just want to make this fupress down the Select buttonthe main screen.
5 9 The clock setting
8/11/2019 BA015B15
18/26
5-9 The clock setting
In a 9screen, press the Select buttonto enterthe clock setting screen.
EX. Now the time is 0:00.
EX. You want to set the clock at 12:05.Press theAdjust buttonto choose the settingvalue.
Now the hour value is flashing!
This is a 24 H clock.
Press the Select buttonto enter the minutesetting screen.
EX. Now the hour is changed from 0 to 12.
Press theAdjust buttonto choose the settingvalue.
Now the minute value is flashing!
Press the Select buttontoscreen.
EX. Now the setting is chaWhen you leave this
is finished.
Press theAdjust buttonto setting screens.
Next page
If you just want to make this fpress down the Select buttonthe main screen.
5 10 The perpetual calendar setting
8/11/2019 BA015B15
19/26
5-10In a 10screen, press the Select buttonto enterthe perpetual calendar setting screen.
EX. Now the perpetual calendar setting is2000/01/01 Saturday.
Press the Select buttonto enter the yearsetting screen.
Press the Select buttonto esetting screen.
EX. Now the year setting is to 2009.
EX. You want to set the perpetual calendarat 2009/07/17.
Press theAdjust buttonto choose the settingvalue.
Press theAdjust buttonto choose the settingvalue.
Press theAdjust buttonto cvalue.
Now the setting value is flashing!
Now the setting value is flashing!
Now the setting value is fl
The year setting rang
Next page Next page
The perpetual calendar setting
If you choose to turn off the calendarfunction, press the Select buttonto
return to a 10screen.Then you could press theAdjust buttonto select other setting screens.
When you adjust theday will adjust autom
The month setting ra
When you adjust theday will adjust autom
Press the Select buttonto esetting screen.
EX. Now the month settingto 7.
5 10 The perpetual calendar setting 5 11 The backlight brightness setting
8/11/2019 BA015B15
20/26
Press theAdjust buttonto choose the settingvalue.
Now the setting value is flashing!
Press the Select buttonto return to a 10setting screen.
EX. Now the setting is changed from 01 to 17.When you leave this screen, the setting
is finished.
Press theAdjust buttonto select the othersetting screens.
5-10
If you just want to make this function setting, you couldpress down the Select buttonfor 3 seconds to back tothe main screen.
The perpetual calendar setting
The date setting range 1~31.
When you adjust the year and date, theday will adjust automatically.
5-11In a 11screen, press the Sethe backlight brightness se
EX. Now the backlight brigbrightest setting).
EX. You want to set the brigPress theAdjust buttonto cvalue.
Now the setting value is fl
Press the Select buttonto rscreen.
EX. Now the setting is chanWhen you leave this
is finished.
Press theAdjust buttonto ssetting screens.
If you just want to make this fupress down the Select buttonthe main screen.
The backlight bright1~5.
The brightness adjus
effective in the LCD
The backlight brightness setting
5 12 The real odometer record setting 5 13 The displayed odometer setting
8/11/2019 BA015B15
21/26
5-12The real odometer record is for you to check
how long the meter already worked.In a 12screen, press theAdjust buttontoselect the other setting screens.
EX. Now the real odometer record is 10,168 km.The setting unit will change together with theunit setting (4-4).
The real odometer record setting 5-13In a 13screen, press the Sethe displayed odometer se
EX. Now the ODO is 0 km.
EX. You want to set the dispas 3,000 km.
Press the Select buttonto myou want to set.
Now the setting value is fla
The setting range: 0Setting unit: 1 km/h
Press theAdjust buttonto cvalue.
Press the Select buttonto rsetting screen.
EX. Now the setting is chan3,000 km.
When you leave this is finished.
The displayed odometer setting
Next page
5-13 The displayed odometer setting The power test screen instruction6
8/11/2019 BA015B15
22/26
Press theAdjust buttonto select the othersetting screens.
If you just want to make this function setting, you couldpress down the Select buttonfor 3 seconds to back tothe main screen.
5-13 The displayed odometer setting
In power test screen, pressto switch from the top spetarget speed t imer.
EX. Now the screen switch
distance timer screen to thscreen.
The power test screen instruction
In power test screen, pressto choose the test you wanfunction is in order as targtarget distance timer, top
In power test screen, pressto switch from the target spdistance timer.
EX. Now it is in the target sp
and the setting is 0~110 km
In power test screen, pressto switch from the target dtop speed timer screen.
EX. Now the screen switch
speed timer screen to thetimer screen, and the setti(0~100 M).
6In main screen, press the S
buttonone time to enter thscreen.
6-1 Target speed timer test
8/11/2019 BA015B15
23/26
6 1 Target speed timer test
WARNING!
In power test screen, press the Select buttonone time to enter the target speed timer testscreen.
Please use this function at racetrack to avoidtraffic accidents.
Please start the test when the bike stops.
If you have the power test record, i t willdisplay the record first. You must clear the
record before starting a new test.
Press theAdjust buttonto clear the recordand enter the target speed timer test screen.
EX. Now you could see the record you havebefore. It displays the target speed timer
setting as 0~110 km/h, the test result: 19"20seconds. The top speed is 110 km/h during thetest., The Max. RPM is 10,000 RPM during thetest.
If you just want to check the record, you could press down
the Select buttonfor 3 seconds to back to the main screen.
When the bike moves, the timer will startautomatically.
Now the is flashing!
About the power test setting, pleasecheck5-5.
Therecord
displayscreen
Enterthe
testing
screenifno
record
Enter
thetesting
screen
Next page
S
P.S.The timer is automatic, so when
your bike start to move thetimer will start to count the timeand stop automatically after youstops the bike.
During the test, the w
When you reach the targe110 km/h), the timer will ssecond).
If you just want to use the func
the Select buttonfor 3 secondback to the main screen.
If you want to test it againbuttonto clear the recordtarget speed timer test sc
0 km/h 3 km/h
S
P.S.If you don't reach the targetspeed or stop acceleratingduring the test, you could presstheAdjust buttonto stop the
timer. Then you could press theAdjust buttonone time to clearthe record and enter the target speed timer test scree
3 km/h0 km/h
6-2 Target distance timer test
8/11/2019 BA015B15
24/26
6 2
WARNING!Please use this function at racetrack to avoidtraffic accidents.
Please start the test when the bike stops.
If you have the power test record, it wil ldisplay the record first. You must clear the
record before starting a new test.
g
In power test screen, press the Select button2 times to enter the target distance timer testscreen.
Press theAdjust buttonto clear the recordand enter the target distance timer test screen.
EX. Now you could see the record you havebefore. It displays the target speed timer
setting as 2/32 mile (100 M), the test result:10"27seconds. The top speed is 63 km/h duringthe test., The Max. RPM is 8,000 RPM during thetest.
When the bike moves, the timer will startautomatically.
Now the is f lashing!
About the power test setting, pleasecheck5-5.
Therecord
displayscreen
Enterthe
testing
screenifno
record
Enter
thetesting
screen
Next page
If you just want to check the record, you could press down
the Select buttonfor 3 seconds to back to the main screen.
S
P.S.The timer is automatic, so when
your bike start to move thetimer will start to count the timeand stop automatically after youstops the bike.
When you reach the targe, the tim
(10"27second).(100 M . 2/32 mile)
If you want to test it again,buttonto clear the recordtarget speed timer test scr
0M
If you don't f inish the targetdistance test or stopaccelerating during the test,
you could press theAdjust
buttonto stop the timer.Then you could press theAdjust buttonone time to cleaenter the target distance timer test screen.
S
P.S.
0M
During the test, the wil
If you just want to use the funct
the Select buttonfor 3 secondback to the main screen.
6-3 The top speed test
8/11/2019 BA015B15
25/26
6 3
WARNING!Please use this function at racetrack to avoidtraffic accidents.
Please start the test when the bike stops.
If you have the power test record, it wil ldisplay the record first. You must clear the
record before starting a new test.
p p
In power test screen, press the Select button3times to enter the top speed test screen.
Press theAdjust buttonto clear the recordand enter the top speed test screen.
EX. Now you could see the record you havebefore. It displays the top speed is 180 km/h,
the distance to reach the top speed is 510 M,The Max. RPM is 10,000 RPM during the test,the time you need to reach the top speed is10"20seconds.
When the bike moves, the timer will startautomatically.
Now the is f lashing!
The top speed test range:Speed: 0~360 km/h. Distance: 0~999
M (3280 feet) RPM: 0~10,000 / 20,000
RPM. Timer: 0~9'59"99seconds.
Therecord
displayscreen
Enterthe
testing
screenifno
record
Enter
thetesting
screen
Next page
If you just want to check the record, you could press down
the Select buttonfor 3 seconds to back to the main screen.
The setting unit will change together with theunit setting (4-4).
The timer is automatic, so
when your bike start tomove the timer wil l startto count the time andstop automatically after
you stops the bike.
S
P.S.
When you reach the top spmeter will stop counting thand time (10"20seconds).
If you want to test it again,buttonto clear the recordtarget speed timer test scr
0M
0 km/h 3 km/h
During the test, the wil
Speed up
If you just want to use the funct
the Select buttonfor 3 secondback to the main screen.
7Trouble shooting
8/11/2019 BA015B15
26/26
The meter doesn't workwhen the power is on.
The meter shows wronginformation.
The power doesn't supply to the meter.Please make sure the wiring isconnected. The wiring and fuse are not
broken.The battery is broken or the battery is tooold to supply enough power(DC 12V) to
make the meter work.Please check the voltage of yourbattery, and make sure the voltage is
over DC 12V.Speed does not appearor appear incorrectly.
Please make sure the speed sensor isconnected correctly.Please check the tire-size setting.
please refer to the manual 5-6.
It is possible that the pconnected wrongly.
Please check is the connect to the perm
battery and the broconnected to the k
posit ive pole.It is possible that the pwire is not connected
Please check the reconnect well or not
The odometer and tripmeter is notaccumulated oraccumulated wrongdata.When switch off, the
needle doesn't returnto 0.
Tachometer does notappear or appearincorrectly.
Please check the RPM sensor wiring is connected correctly.
Please check the spark plug is R type
or not. If not, please replace the sparkplug with the R type spark plug.Please check your setting.
Please refer to the manual 5-7.Temp does not appearor appear incorrectly.
Please check the sensor.Does the wiring break or fal ling off ?
Please check your fuel tank.Is there any fuel inside ?
Please check the wiring.Do you connect the wiring correctly ?
Please check the setting.Please refer to the manual 5-8.
The following situation do not indicate malfunction of the meter.Please check the following before taking it in for repair.
Trouble TroubleCheck item Check item
If stil l can't solve the problems according to the stepcontact with distributors or us.
Fuel gauge does notappear or appear
incorrectly.
The clock is incorrect.