Brh Eplug Rotaryshaftvalves Ge

7/31/2019 Brh Eplug Rotaryshaftvalves Ge

1/28

3

November 2001

D102441X412

Product Flier PF51.3:eplugt

eplugt Rotary-Shaft Valves for

General and Severe Service

W8192W8287 / IL

J Rotary valve efficiency with globe valve ruggedness forgeneral gas, steam, or liquid service and for fibrous slurryapplications

J DN 25 to DN 500 DIN sizes and 1- to 20-inch ANSI sizes

J Choice of seal types and materialscomposition, flat metal,heavy-duty metal, or flow ring

J Temperatures to 427_C

J Pressures to DIN PN40 and ANSI Class 600

J ENVIRO-SEALR packing systems to help ensure compliancewith environmental emissions requirements

J FIELDVUERdigital valve controllers offer digital control andremote diagnostics. The proven line of Fisher positioners,controllers, transmitters, and switches also is available.


2/28

Product Flier PF51.3:eplug

2

Rugged Rotary Valves

The Design V500 valve usesrugged valve components and achoice of erosion-resistant trimmaterials for highly erosive andsevere operating conditions.

The Design CV500 valvecombines the rangeability of thecammed-segmented V-notchedball, with the inherent ruggednessfound in the Design V500 heavyduty bearings, seals and body.This combination provides abalance of high capacity, erosionresistance and pressure controlfor gas and liquids.

The Design V500 and CV500 areexceptional erosion-resistant

valves.

The Design V500 valve uses aneccentric plug to control flow. It is

available in four types oferosion-resistant trim, includingone of ceramic material.

The Design CV500 offers all thehigh temperature, high pressure,and sealing capabilities of theDesign V500 valve, and it addsthe high rangeability, highcapacity, and throttling capabilityof the V-notch valve.

Both designs are available withintegral flanges or as flangelessvalves.

Rugged Construction...Oversized shaft diameters in theDesign CV500 and V500 valves

give these valves high pressurecapability. The one-piece bodyeliminates gaskets that might leakas a result of pipeline stresses.

Long Seat Life...The eccentricaction of the valve plug or ballmoves the plug away from theseat as soon as the valve opens.This action reduces seat wearand friction. The patented seatring dynamically aligns with theplug as the valve closes. Thealignment process laps theseating surfaces for extendedseal life. The seat ring has twoshutoff surfaces so it can bereversed to extend the servicetime.

The Design BV500 valvefeatures a specially contouredeccentric plug. The seat ring isgasketed and is retained with a

screwed-in retainer.Metal-to-metal seating isstandard, and soft (PTFE) seatingis optional. The Design BV500offers an exceptional solution formany less-severe general-serviceapplications, includinglowpressure steam and fluids.

W4170-3*/IL

W5739-1/IL

Design V500 Valve

Design CV500 Valve

Design BV500 Valve

W8080 / IL


3/28


3

Rugged Rotary Valves (Continued)

W5806-1/IL

ENVIRO-SEALR Packing System(Single PTFE V-Ring)

PACKING STUD

PACKING NUT

O-RING

PACKINGFOLLOWER

PACKINGSET

PACKING BOXRING

O-RING

14B9917-BE0735 / IL

Leak-off Packing Assembly for1- through 12-inch Valves

Other Rotary Valves

Designs V150, V200, andV300...These Vee-BallR valvesuse the time-proven V-notch ballthat provides high-capacitycontrol of liquid, gas, steam, andfibrous slurries. The shearingaction of the ball allows smooth,non-clogging operation, and theunrestricted, straight-through flow

ensures high capacity.Design V250...The Design V250valve is a heavy-duty valve oftenused in gas transmission lines,gas distribution, or liquidpipelines. It is available in sizes to24-inches and Class 600 or 900pressure-temperature ratings.

Design V260...The Design V260valve has special energy-dissipating trim to reduce noiseeffects that cause pipelinevibrations. It is available in 8-,10-, and 12-inch ANSI valves.

Types 8532, 8560 &8510/8510B...The ediscR family

of high performance butterflyvalves is designed for optimalcontrol performance, as well astight shutoff isolation service.These valves are available in sizerange 2 to 24-inch and a varietyof pressure classes and bodystyles.

Type A11, A31A, A31D, A61D &A41... The Posi-SealR HighPerformance Butterfly Valves aredesigned for isolation on/offservice as well as low tier control.These valves feature key, doubled or square shafts. These valveare available in sizes 2 through72-inch and pressure classes up

to 2500.Basis Weight ControlValve...Design V150, V200, andV300 valves are available with anelectric actuator and controlcircuits to meet the precisioncontrol requirements of basisweight control in the papermaking industry.

W5000/IL

Typical Flangeless V500 Construction


4/28


4

Rugged Rotary Valves (Continued)

Actuators

W8124

Type 1052 Actuator Type 1061 Actuator

W8192/IL

Type 1051 and 1052 PneumaticDiaphragm Actuators...Rugged,heavy-duty spring-returnactuators. These actuators areavailable with a variety ofinstrument accessories,handwheels, adjustable travelstops, and a maintenancelock-out device.

Type 1061 Pneumatic Piston

Actuator...Heavy-duty pistonactuator available with a variety ofinstrument accessories,handwheels and piston bypass

valves, and a maintenancelockout device.

Type 1077 Manual HandwheelActuator...Available formanual-only operation.

Actuator Accessories

FIELDVUER Digital ValveController...Available mountedon Type 1051 and 1052actuators.

Positioners andTransducers...Pneumaticpositioners and electro-pneumaticpositioners and transducers canbe provided with these actuators.

Position Transmitters,Solenoid Valves, VolumeBoosters, and LimitSwitches...Also available.

MOUNTING ACTION(1)BALL ROTATION TO

CLOSE(2)CV500V500

PLUG ROTATION TOCLOSE(2)

BV500

Right-Hand PDTCPDTO

CCWCCW

AB

CWCW

BA

Left-HandPDTCPDTO

CCWCCW

DC

CWCW

CD

1. PDTCPush-down-to-close, and PDTOPush-down-to-open.2. CCWCounterclockwise, and CWClockwise.

LEFT-HANDMOUNTING

STYLE C

STYLE D

RIGHT-HANDMOUNTING

STYLE B

STYLE A

A1579-4/IL

The Actuators are Available in any ofFour Styles and Positions (Above thePipeline as Shown Here, Below, orParallel with the Pipeline)


5/28


5

Selecting Rotary Valve Products

Only a few of the more commonly selected product materials,sizes, options, and accessories are covered in this flier.

Contact your nearest sales office (refer to the back cover) forassistance in selecting and sizing these products. Moredetailed specifications are available on request.

Selecting Valve Components

Valve Type Selection 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .Body Materials, End Connections, and Ratings 6. . . . . .Valve Component Materials and Temperatures 7. . . . . .

Selecting an Actuator

Type 1051 and 1052 Pneumatic Diaphragm Actuators 9Type 1061 Pneumatic Piston Actuator 10. . . . . . . . . . . . .

Selecting Accessories

FIELDVUER Digital Valve Controller 11. . . . . . . . . . . . . .3610J Series Valve Positioners 12. . . . . . . . . . . . . . . . . . .Other Accessories 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reference Information

Shutoff Pressure Drop Limits for Trim Parts 15. . . . . . . .Flow Coefficients 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Conversions for Other Sizing Equations 18. . . . . . . . . . .

Actuator-Valve Selection (Shutoff Pressure Drop) 19. .Approximate Weights 21. . . . . . . . . . . . . . . . . . . . . . . . . . .Typical Dimensions 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ordering Information 23. . . . . . . . . . . . . . . . . . . . . . . . . . .Sales Offices and Sales Representatives 24. . . . . . . . .

Valve Type Selection

APPLICATION SHUTOFF

Service TemperatureEnd Connection and Body

Rating

VALVETYPE

SIZES, DIN ORINCHES

VALVE BODYMATERIAL

SHUTOFFCLASSIFI-

CATION

Erosive service where

extremely ruggedconstruction is required(rangeability of 100 to 1)

to 538_C

Flanged: DIN PN10 - PN 100 or

ANSI Class 150 - 600Flangeless: ANSI Class 150 -

600

V500

Flanged: DN 25 -

DN 200 DIN or 1 - 8inches ANSIFlangeless: 3 - 8

inches ANSI

WCC steel orCF8M(316 stainless steel)

Class IV(0.01% of

valve

Erosive service where abalance of rugged

construction and highcapacity is required

(rangeability of 200 to 1)

to 427_C

Flanged: DIN PN 10 - PN 100 orANSI Class 150 - 600

Flangeless: ANSI Class 150 -600

CV500

Flanged: DN 80 -DN 300 DIN or 3 -

12 inches ANSIFlangeless: 3 - 8

inches ANSI

CF3M, DIN 1.0619steel, DIN 1.4581

stainless steel,WCC steel or CF8M

capacityin either flow

direction)

Non-erosive generalservice or where integral

noise attenuation isrequired

(rangeability of 100 to 1)

to 427_CFlanged: DIN PN 10 - PN 40 or

ANSI Class 150/300BV500

Flanged: DN 25 -DN 150 DIN or 1 - 6

inches ANSI

WCC steel orCF3M

Forwardflow only;Class IVfor metalseal and

Class VI forPTFE Seal


6/28


6

Body Materials, End Connections, and Ratings

Design BV500

VALVE BODY SIZES RAISED-FACE FLANGES ORVALVE BODYMATERIAL DIN Inches

RAISED-FACE FLANGES ORFLANGE COMPATIBILITY

RATING

Flanged Valves

WCC steel or CF3M DN 25, 40, 50, 80, PN10, 16, 25, 40, and PN10, 16, 25, 40, andWCC steel or CF3M(316 SST)

DN 25, 40, 50, 80,100, 150 1, 1-1/2, 2, 3, 4, 6

PN10, 16, 25, 40, andClass 150, 300

PN10, 16, 25, 40, andClass 150, 300

Design CV500



RATING

Flanged Valves

WCC steel or CF8M DN 80, 100, 150, 200 3, 4, 6, 8PN10/16, 25/40, 63/100, and

Class 150, 300, or 600PN10/16, 25/40, 63/100and Class 150, 300, 600

(316 stainless steel)DN 250, 300 10, 12 PN 25, 40, and Class 300 PN 25, 40 and Class 300

Flangeless Valves

WCC steel or CF8M - - - 3, 4 Class 150, 300, 600 Class 150, 300, 600WCC steel or CF8M(316 stainless steel) - - - 6, 8 Class 150, 300 Class 150, 300

Design V500



RATING

Flanged Valves

WCC steel or CF8M(316 stainless steel)

DN 25, 40, 50, 80,100, 150, 200 1, 1-1/2, 2, 3, 4, 6, 8

PN10/16, 25/40, 63/100, andClass 150, 300, or 600

PN10/16, 25/40, 63/100and Class 150, 300, 600

Flangeless Valves

WCC steel or CF8M - - - 3, 4 PN10 - 100 and Class 150, 300, 600 Class 150, 300WCC steel or CF8M(316 stainless steel) - - - 6, 8 Class 150, 300 Class 150, 300


7/28


7

Valve Component Materials and Temperatures for Design BV500

BODY, SEAT AND BUSHINGS TEMPERATURE

_BODY SEAT RING GUIDE BUSHING _C

H S31600 (316 SST) or H S31600H 440C stainless steel,

H Alloy 629 to 400

WCC steelwith CoCr-A seating surface

PEEK/PTFE 29 to 260WCC steel

S31600 with PTFE insert H 440C stainless steel, H Alloy 6, or H

PEEK/PTFE

20 to 232

H S31600 (316 SST) or H S31600 PEEK/PTFE 196 to 260

CF3M (316 SST)S31600 (316 SST) or S31600with CoCr-A seating surface Alloy 6 196 to 400CF3M (316 SST)

S31600 with PTFE insert H PEEK/PTFE or H Alloy 6 196 to 232

OTHER PARTS

Packing (ProcessPTFE V-Ring 196 to 232

Packing (ProcessTemperatures Assume ENVIRO-SEAL Single PTFE V-ring (500 ppm service) 46 to 232Temperatures Assume

Uninsulated Valve Neck) ENVIRO-SEAL Graphite (500 ppm service) 7 to 316

DN 25, 1-, or 1-1/2 inch sizes: CoCr-A (alloy 6)Valve Plug

DN 25, 1-, or 1-1/2 inch sizes: CoCr-A (alloy 6)Larger sizes: Chrome-plated CF8M (316 stainless steel) or CF8M with CoCr-A Overlay

Seat Retainer CF8M

Shaft S20910 (Nitronic 50 stainless steel)

Gasket Graphite

Packing Follower S30400 stainless steel, fiberglass/PTFE, fluoroelastomerBolting A193 B8M bolts; A194 8M nuts

Optional Noise AttenuatorDisk

CF8M

Valve Component Materials and Temperatures for Design CV500

SEAT RING, SHAFT, AND V-NOTCH BALL NOTES

Seat RingH CF3M (316L SST), H CF3M with CoCr-A (alloy 6) seat,

H CF8M (316 SST), H CF8M with CoCr-A seat, andHR30006 (alloy 6) Refer to the section below for

Valve Shaft H S17400 (17-4PH SST) or H SA479 Grade XM-19 SSTRefer to the section below for

temperatures

V-Notch BallH Chromium-plated CF3M (316L SST) or

H chromium-plated CF3M with CoCr-A bore

temperatures

VALVE BODY, SEAT RETAINER, BEARINGS, AND PACKING - - -MAXIMUM

TEMPERATURE, _C

VALVE BODY RETAINER BEARINGPTFE

Packing

GraphiteRibbonPacking

NOTES

H CB7Cu-1 (17-4PHPTFE/Composition/S31603

(316L SST) 232 232 S Minimum temperatures are 10_C for_DIN 1.0619 steel SST), CF3M,

or H R30006 H Alloy 6 or H S44004 (440CSST) 260 316

DIN valve bodies, 26_C for steel ANSIvalve bodies, and 46_C for SST ANSIvalve bodies

HCF3M or H DINH CF3M, H CF3M

with CoCr-A bore, orPTFE/composition/S31603 232 232

valve bodiesS For steel bodies with CF8M retainer,limit maximum temperature to 260_C.CF3M or DIN

1.4581 SSTwith CoCr-A bore, or

H R30006Alloy 6 260 316

S PTFE packing is available with orwithout one carbon-filled PTFE ring for

H CB7Cu-1 (17-4PH PTFE/composition/S31603 232 232

grounding.S With ENVIRO-SEAL packing,WCC steel SST), CF8M, (see

notes) or H R30006 Alloy 6 or S44004 260 316With ENVIRO-SEAL packing,

temperature limits vary with pressure and

H CF8M,H CF8M with

PTFE/composition/S31603 232 232

fugitive emissions standards; contactyour nearest sales office for information.S Use S44004 bearings with steel bodyCF8M

CF8M withCoCr-A bore, or

H R30006 Alloy 6 260 316

Use S44004 bearings with steel bodyand S17400 shaft only.

OTHER PARTS - - -

Part Material Temperature, _C

O-Rings for optional Nitrile to 93O-Rings for optionalsealed bearings Fluoroelastomer 18 to 204

Face seals PTFE/Hastelloy C & Inconel X718 S Optional sealed bearings are available

Gasket S31603 or S31600 Refer to the section abovewith alloy 6 and S44004 bearings only

B7 and 2H or B7M and 2HM steelRefer to the section above

for temperaturesBolting

B8M and 8M 316 SST


8/28


8

Valve Component Materials and Temperatures for Design V500

VALVE BODY AND SHAFT NOTES

Valve Body HWCC steel or HCF8M (316 stainless steel)

Valve ShaftHS17400 (17-4PH stainless steel) or

HSA479 Grade XM-19 SST

Refer to the parts below fortemperatures

PLUG, SEAT RING, BEARINGS, AND PACKING - - -

MAXIMUM

TEMPERATURE, _C

PLUG AND SEAT RING RETAINER BEARINGPTFE

Packing

GraphiteRibbonPacking

NOTES

Trim Level 1

Plug: Chrome-plated 316 HCB7Cu-1 (17-4PHPTFE/Composition/316

stainless steel 232 232stainless steel

Seat Ring: 316 stainless steelseat ring

stainless steel) (WCCsteel body) or H 316

stainless steel

HAlloy 6 orHS44004

(440C stainless steel)260 427

S Minimum temperatures are10_C for DIN valve bodies,

Trim Level 210 C for DIN valve bodies,26_C for steel ANSI valve

Solid alloy 6 (DN 25 - 10 or 1 -4 inch) or 316 stainless steel

HCB7Cu (steel body) or

PTFE/composition/316stainless steel 29 to 232 29 to 232

bodies, and 46_C for SST ANSIvalve bodiesS PTFE packing is available withwith CoCr-A on plug face and

seat ring seat surface (larger

sizes)

CB7Cu (steel body) orH316 stainless steel HAlloy 6 or

HS4400429 to 260 29 to 427

PTFE packing is available withor without one carbon-filled PTFE

ring for grounding.STrim Level 3

S With ENVIRO-SEAL packing,temperature limits vary with

H316 stainless steelwith alloy 6 sleeve bore

PTFE/composition/316stainless steel 29 to 232 29 to 232

temperature limits vary withpressure and fugitive emissionsstandards; contact your nearest

Solid alloy 6 (DN 25, 40 or 1, 1-1/2inch) or Hsolid alloy 6

(larger sizes)HAlloy 6 or

HS4400429 to 260 29 to 427

sales office for information.S For temperatures from 427_C to538_C, (DN 25, 40 or 1, 1-1/2 inch

Trim Level 4only). Contact your nearest salesoffice

Plug: Solid ceramic (DN 1 -50 or 1 - 2 inches) or ceramic

plug bolted to alloy 6 hub

H316 stainless steelwith ceramic bore (DN

25, 40 or 1, 1-1/2

PTFE/composition/316stainless steel 232 232

officeS Use S44004 bearings with steelbody and S17400 shaft only.

(assembly also contains 316stainless steel and grade 5

titanium parts) (larger sizes)Seat ring: Solid ceramic

25, 40 or 1, 1-1/2inches) or H solid alloy 6

retainer with ceramicbore (larger sizes)

HAlloy 6or HS44004

260 427

OTHER PARTS - - -

Part Material Temperature, _C

O-Rings for optional sealed Nitrile 29 to 93O-Rings for optional sealedbearings Fluoroelastomer 18 to 204

Face seals PTFE/Hastelloy C & Inconel X718 S Optional sealed bearings are

Gasket HGraphite (DN 25, 40 or 1, 1-1/2 inch) orHS31603 & S31600 (larger sizes) Refer to the parts and

available with alloy 6 and S44004bearings only

HB7 and 2H or HB7M and 2HM steelmaterials above.

BoltingB8M and 8M 316 SST

Seal Detail for Design CV500 and V500W5793-1/IL

FACE SEALS

SEAT RING

BALL OR PLUG

RETAINER


9/28


9

Type 1051 and 1052 Actuators

Type 1051 and 1052 pneumaticdiaphragm rotary actuators arespring-return actuators thatprovide reliable operation for thevalves in this flier.

The Type 1051 actuator issuitable for on-off operation or forthrottling operation whenequipped with a valve controlleror positioner. They Type 1052actuator is suitable for on-off orthrottling with or without acontroller or positioner.

These actuators featuresingle-joint linkage withsplined-and-clamped levers forminimum lost motion and high

control accuracy.

The actuator-valve linkage iscompletely enclosed for safety,yet the packing adjustment isaccessible without removing anyparts.

Specifications...Refer to thetable below and the actuatorselection tables.

Options...J Top-mountedhandwheel, J Type 1078declutchable handwheel actuator,J Adjustable up- anddown-travel stops, J Actuatorlocking mechanism that keeps theactuator in a locked positionduring maintenance, and JPipe-away vent for remoteventing of the actuator housing.

Accessories...J Pneumatic andelectro-pneumatic valvepositioners, J FIELDVUER

digital valve controller, and J

Limit and proximity switches.

ACTUATORSIZE

NOMINAL OPERATINGPRESSURE RANGES

MAXIMUMCASING

PRESSURE,BAR

MAXIMUMVALVE

BREAKOUT

TORQUE, NSm

AMBIENTTEMPERATURES,

_

MATERIALS

Type1051

Type1052

Bar PsigType1051

Type1052

Type1051

Type1052

_C

33 33 H0 to 1.2,H0 to 2.3, H0 to 18, H0 to 33, 4.5 85 132 Diaphragm: Nitrile

(standard) or silicone40 40

H0 to 2.8, andH0 to 3.8

H0 to 40, andH0 to 55 5.2 322 371

(standard) or siliconeelastomers

O-rings (for optional

60 60H0 to 1.2,H 0 to 2.3,

and H0 to 2.8

H 0 to 11, H0 to 33,and H0 to 40

3.4 626 730Nitrile:40 to 82

Silicone:50 to 149

O-rings (for optionalhandwheel): Nitrile or

EPDMHousing: Cast iron

- - - 70H 0 to 2.3,H 0 to 2.8,

and H 0 to 3.8

H 0 to 33, H 0 to 40,and H 0 to 55

- - - 4.5 - - - 1370

(standard) or steelOther Major Metal

Parts: Aluminum, steel,or cast iron

Size 33 Actuator

W4742-1/IL

Typical Type 1052 Actuator

W3813-1/IL


10/28


10

Type 1061 Actuators

Type 1061 pneumatic rotaryactuators are double-actingpiston actuators that providereliable operation for the valves inthis flier.

The Type 1061 can be used witha two-position control signal foron-off operation or with a valvecontroller or positioner forthrottling operation.

These actuators featuresingle-joint linkage withsplined-and-clamped levers forminimum lost motion and highcontrol accuracy.

The actuator-valve linkage is

completely enclosed for safety,yet the packing adjustment isaccessible without removing anyparts.

Specifications...Refer to thetable below and the actuatorselection tables.

Options...J Type 1078declutchable handwheel actuatorwith cylinder bypass valve,J Adjustable up- anddown-travel stops, J Actuatorlocking mechanism that keeps theactuator in a locked positionduring maintenance, and JPipe-away vent for remoteventing of the actuator housing.

Accessories...J Pneumatic andelectro-pneumatic valvepositioners and J Limit andproximity switches.

CYLINDER OPERATING PRESSURE, BAR MAXIMUM AMBIENTACTUATOR

SIZE MinimumRecommended

MaximumAllowable

VALVEBREAKOUT

TORQUE, NSm

AMBIENTTEMPERATURES,

_CMATERIALS

30 6.9 232 Cylinder and flange: Aluminum

40 10.3 847Piston: Aluminum or nylon-coated

aluminum60 Without positioner: 1.4 6.9 1130 34 to 82

aluminumO-rings: Nitrile

68With positioner: 0.35 bar

above actuator requirement 5.9 1540(to 50 with optional

materials)Mounting yoke bushing: PTFE

and steel

80

above actuator requirement

10.3 5080

materials) Sliding seal: Brass

100 10.3 6290Other parts: Iron, aluminum, and

stainless steel

W3827-1/IL


11/28


11

Type DVC5020 Digital Valve Controller

FIELDVUE digital valvecontrollers are communicating,microprocessorbased controllersthat convert a current signal to apressure signal to operate theactuator. Through the HART

communications protocol, thecontroller gives easy access toactuator-valve information that iscritical to process operation.

The Type DVC5020 controller isavailable to mount on Type 1051and 1052 actuators.

ValveLink Software...ValveLinksoftware allows easy access tothe information available from theFloVuet system. The softwareprovides diagnostic informationsuch as dynamic error band andstep response oneasy-to-interpret screens .

Access to diagnostics is througha Model 275 HART communicatoror a personal computer usingWindowst software.

FIELDVUE Valve Controller Physical Specifications

SUPPLY PRESSURE, BAR STEADY-STATE

Minimum andRecommended

Maximum

OUTPUTSIGNAL

AIRCONSUMPTION,

Nm3/H

TEMPERATURELIMITS

WEIGHT HOUSING

As needed byactuator

6.5Up to 95% of

supply pressure

Less than 0.3 at1.4 bar supply

pressure40 to 80_C 2.7 kg

IP 65 per IEC 60529NEMA 4X

FIELDVUE Controller Electrical Specifications

ELECTRICAL INPUT

Analog Input Signal VoltageMinimum

Control Current

MinimumCurrent withoutMicroprocessor

Restart

MaximumCurrent

PolarityProtection

DIGITALCOMMUNICATION

INPUT SIGNAL

H 4 to 20, H 4 to 12 orH 12 to 20 mA dc(user adjustable)

12 Vdc minimumand 30 Vdcmaximum

4.0 mA 3.5 mA 100 mA30 Vdc

minimum withoutdamage

HART 1200 baudfrequency shift

keyed

FIELDVUE Digital Controller Certifications

INTRINSIC SAFETYINTRINSIC

SAFETY OR

NON-INCENDIVE

FLAMEPROOF DIVISION 2EXPLOSION-

PROOF

LCIECSA(1) or

FM(1)SAA LCIE SAA CSA FM CSA or FM

EEx ia IICT5

Class I,Division 1,

Groups(1) A, B,C, D

T5 (Tamb 80_C)

Ex n IIC T5, T6Ex ia IIC T4, T5,

STET

EEx d IIB +H2

T5 (Tamb80_C)

EEx d IIB +H2

T6 (Tamb80_C)

Class I Division 2,Groups A, B, C, DClass II, Division 2

Groups E, F, G


Groups F, G

Class I Division 1Groups B, C, D

Class II, Division 1,Groups E, F, G

1. Contact your nearest sales office for the appropriate FM and CSA entity ratings and CSA parametric ratings for each group.

Type DVC5020 Controller on aValve and Actuator with Model 275

HART Communicator

W6161/IL


12/28


12

3610J Series Valve Positioners

The 3610J Series pneumatic and3620J Series electro-pneumaticvalve positioners can be usedwith Type 1051, 1052, or 1061actuators for accurate valvepositioning in throttlingapplications.

The positioners provide accurate,fast response and can withstandthe vibrations in most plants.

The positioners are easilyreversible for direct or reverseaction without additional parts.

The 3610J positioners are singleacting for Type 1051 and 1052actuators, and the 3610JPpositioners are double acting forType 1061 actuators.

Options...H Supply pressuregauge, H Tire valves for clip-ongauges, and H Integrally mountedbypass valve for single-actingactuators

3610J and 3620J Positioner Specifications

Type Input Signal Supply PressureOperative

TemperatureWeight Connections

3610J and3610JP

H 0.2 to 1.0 orH 0.4 to 2.0 bar

H 3 to 15 orH 6 to 30 psig

0.3 bar above theactuator requirement

up to 10.3 barmaximum

40 to 82_C 2.5 kgPressure and Vent

3620J and3620JP

4 to 20 mA constant current with30 Vdc maximum compliance

voltage; equivalent circuit is 120ohms shunted by three 5.6 V

zener diodes

0.3 bar above theactuator requirement

up to 10.3 barmaximum

40 to 82_C 3.6 kg

Connections: 1/4-inch NPTType 3620J and JP

Conduit: 1/2 NPT

3610J and 3620J Series Capacities and Housing

Type Supply Pressure, BarSupply Air Demand,

Nm3/hAir Consumption, Nm3/h

Housing (Types 3620Jand 3620JP)

1.4 13 Type 3610J: 0.40 to 1.4 bar supply IP 54 per IEC 60529,3610J and 3620J2.4 17

Type 3610J: 0.40 to 1.4 bar supplyType 3620J: 0.49 at 1.4 bar supply NEMA 3; vent should be

5.2 37 Type 3610JP: 0.64 at 6.9 bar supplyon the side or bottom

for weatherproof3610JP and 3620JP6.9 46

Type 3610JP: 0.64 at 6.9 bar supplyType 3620JP: 0.93 at 6.9 bar supply

for weatherproofapplications

Electro-Pneumatic Certifications

INTRINSIC SAFETYINTRINSIC

SAFETY ORNON-INCENDIVE

FLAMEPROOF DIVISION 2EXPLOSION-

PROOF

PTB CSA(1) or FM(1) SAA LCIE SAA CSA FM CSA or FM

EEx ia IICT4, T5, T6

Class I, Division1, Groups(1) A,

B, C, D

CSA T4, FM T4A

Ex ia IIC T4Ex n IIC T4

EEx d IIC T4,T5, T6

Ex d IIC T6


Groups E, F, G


Groups F, G

Class I Division 1Groups A, B, C, DClass II, Division 1,

Groups E, F, G1. Contact your nearest sales office for the appropriate FM entity ratings and CSA parametric ratings for each group.

W4920-1*/IL


13/28


13

Other Accessories

Type 3065 Limit Switch Box

The limit switch box can beinstalled on the actuator to holdproximity or microswitches, whichcan turn on an alarm or display

device when a pre-set limit isreached. Additionalmicroswitches are available.

The device has separate camsfor open and closed positions,and adjustment of one cam doesnot affect the other.

Certifications...CE Mark to EMCdirective H EN 50081 andH EN 50082

Self-Adjusting...Complicatedadjustments are not required.

Standardized Installation...Covered by IEC 534-6 (NAMUR).The box can be supplied with amounting kit.

Type 3065 Limit-Switch Box Specifications

HousingMaterial

AmbientTemperature

(for

Housing)

DIN 40 050ProtectionClass (for

Housing)

Available Switches

Type EI - S inductive proximity switchSlot shaped

Type EMmicroswitch

P & F Model SJ3.5 N or SN Burgess V4NT7AR1

Markalonplastic 40 to 80_C IP 65

25 to 100_C (N)25 to 100_C (SN)DIN 40 050IP 67

40 to 80_CDIN 40 050IP 54

Rating voltage is 8 V = (RiX1k)Operating voltage is 5 - 25 V

Rating voltage is 8 V = (RiX1k)Operating voltage is 5 - 25 V

Power input is > 3 mA with active surfaceuncovered

Power input is > 3 mA with active surfaceuncovered

Type EI - Z inductive proximity switchCylindrical shaped

Type EM-Exmicroswitch

P & F Model NJ 2-11-N-G or SN-G Bartec 07-2501-6-30/63

Aluminum 40 to 80_C IP 65

25 to 100_C (N-G)

25 to 100_C (SN-G)DIN 40 050IP 68

25 to 70_CDIN 40 050IP 54

Alternating current switching capacity is 125 or250 V with 5.0 A resistive load, 0.5 A light-bulb

load, and 5.0 A inductive load

Alternating current switching capacity is 125 or250 V with 7.0 A resistive load, 0.5 A light-bulb

load, and 5.0 A inductive load

Direct current switching capacity is up to 250 V with up to 0.25 A resistive load, 0.1 a (opening)and 0.2 A (closing) light-bulb load, and up to 0.03 A inductive load

W6682B/IL


14/28

W7412 W4727

Type 67CFR Filter-Regulatorwith Optional Gauge

Type 2625 Volume Booster


14

Other Accessories (Continued)

Type 67CFRFilter-Regulator...The Type67CFR provides constantlycontrolled supply pressure toactuator accessories system. This

regulator features an internal filterand limited-capacity internal relief,allowing partial reduction ofdownstream pressure.

Type 67CFR Filter-Regulator Specifications

OUTLET PRESSURESETTINGS

MAXIMUMINLET

PRESSURE

MAXIMUMDIAPHRAGM TEMPERATURE

CONNECTIONS

MAXIMUMFLOW WEIGHT,

Bar Psig

(BODYRATING),

BAR

PRESSURE,BAR

CAPABILITIESCONNECTIONS

COEFFICIENT, CV

kg

0 to 1.40 to 2.40 to 4.10 to 8.6

0 to 200 to 350 to 60

0 to 120

17.2

3.4 overoutlet setting

or 7.6,whichever is

greater

Nitrile diaphragmand plug:40 to

82_CFluoroelastomer

diaphragm and plug:

18 to 149_C

Inlet and Outlet:1/4-inch NPT femaleVent: H 6.4 mm hole

or H 1/4-inch NPTfemale

0.36 0.5

Type 646 or 846 Electro-Pneumatic Transducers...Thesetransducers convert a standard 4to 20 mA dc signal to aproportional pneumatic signal.Certifications are H CE Mark toEMC directive (electromagneticcompatibility);H Contact your nearest salesoffice for intrinsic safe andflameproof ratings.

Type 2625 VolumeBooster...The volume boostercan be used in conjunction with apositioner to increase actuatorstroking speed.

Others...H High-pressure supplypressure regulators, H proximityswitches, H microswitches, andH solenoid valves.

Contact your nearest sales officefor more information.


15/28


15

Shutoff Pressure Drops Limits for Trim Parts

WARNING

Pressure drops inthe following tablesconsider only thetrim parts (plug,shafts, bearings, andseals).

The pressure dropsshown might behigher than the DINor ANSI pressure-temperature rating ofthe valve. Do notexceed DIN or ANSIpressure-temperature ratings,as exceeding thepressure-temperature ratingmay cause personalinjury or equipmentdamage.

In the following tables, the lowertemperature limits is 10_C for DINvalves, 29_C for ANSI steelvalves, and 46_C for ANSIstainless steel valves.

Also refer to the actuator sizingpages to select an actuator size.

Contact your Fisher sales officefor Design BV500 valve pressuredrops.

Design CV500 Valves

Bearing Material Valve Sizes Temperature, _C Pressure Drop, Bar

DN 80 - 150 (3 -6 inches) to 316 41.4

S44004DN 200 (8 inches)

to 149204260

24.123.823.1

DN 250 (10 inches) to 316 24.1

DN 300 (12 inches) to 316 27.6

DN 80 and 100 (3 and 4 inches) to 316 41.4

DN 150 (6 inches) to 316 20.7

R30006 DN 200 (8 inches) to 316 15.2R30006DN 250 (10 inches) to 316 24.1

DN 300 (12 inches) to 316 27.6

DN 80 - 150 (3 -6 inches) to 232 41.4

PTFE/Composition-lined S31603

DN 200 (8 inches) with S17400shaft

to 93149204232

24.124.123.823.4PTFE/Composition-lined S31603

(limit to 207_C for hot water andsteam) DN 200 (8 inches) with ASME

SA-479 XM-19 shaft

to 93149204232

24.123.122.121.7

DN 250 (10 inches) to 232 31.0

DN 300 (12 inches) to 232 34.5

Design V500 Valves with S44004 Bearings

VALVE SIZE, DIN DN AND INCHES

TEMPERATURE, _C DN 25 DN 40 DN 50 DN 80 DN 100 DN 150 DN 200TEMPERATURE, C

1 1-1/2 2 3 4 6 8

Level 1 Trim

29 to 149204316

68.968.968.9

55.255.255.2

41.441.441.4

41.441.441.4

41.441.441.4

41.441.441.4

24.123.823.1

Level 2 and 3 Trims

29 to 93149204260316343371399427

103.4100.397.291.783481.078.369.656.9

103.4100.397.291.783.481.078.369.656.9

103.499.093.891.483.481.078.369.656.9

103.4100.397.291.783.481.078.369.656.9

82.782.782.782.782.781.078.369.656.9

51.751.751.050.049.348.348.346.946.9

24.124.123.823.123.122.422.421.721.7

Level 4 Trim

29 to 93149204260316317427

103.4100.397.291.783.478.356.9

103.4100.397.291.783.478.356.9

70.370.370.370.370.370.356.9

103.4100.397.291.783.478.356.9

78.678.678.678.678.678.356.9

52.452.451.050.049.348.346.9

24.124.123.823.123.122.421.7


16/28


16

Shutoff Pressure Drop Limits for Trim Parts (Continued)

Design V500 Valves with PTFE/CompositionBearings

Limit to 207_C with Hot Water or Steam Service

SIZES

DIN

DN Inches

VALVE

MATERIAL

TEMPER-

ATURE,_

C

PRESSURE

DROP, BAR

Level 1 Trim

WCC 29 to 232 68.925 1

CF8M 46 to 204232

68.965.8

4050 - 150

1-1/22 - 6

BothBoth

to 232to 232

55.241.4

Both with17-4PH

shaft

to 149204232

24.123.823.4

200 8Both withSA-479

SM-19 shaft

to 93149204232

24.123.122.121.7

Level 2 and 3 Trims

WCC

29 to 93149204232

103.4100.397.291.7

25 - 80 1 - 3

CF8M

46 to 3893

149204232

99.385.577.371.065.8

WCC 29 to 232 89.6

100 4CF8M

46 to 3893

149204232

89.685.577.271.065.8

WCC with14-4PH

shaft

29 to 149204232

55.254.853.8

WCC withSA-479

SM-19 shaft

29 to 149204232

55.251.550.0

150 6 CF8M with17-4PH

shaft

46 to 93149204232

55.253.154.853.8

CF8M withSA-479

SM-19 shaft

46 to 93149204232

55.253.151.050.0

Both with

17-4PHshaft

to 149

204232

24.1

23.823.4200 8

Both withSA-479

SM-19 shaft

to 93149204232

24.123.122.121.7

Design V500 Valves with Alloy 6 Bearings

SIZES

DINDN

Inches

VALVEMATERIAL

TEMPER-ATURE, _C

PRESSUREDROP, BAR

Level 1 Trim

WCC 29 to 316 68.9

25 1CF8M

46 to 204260316

68.965.862.4

4050 - 100

150200

1-1/22 - 4

68

BothBothBothBoth

to 316to 316to 316to 316

55.241.420.715.2

Level 2 and 3 Trims

WCC 29 to 204427

68.956.9

25 1CF8M

46 to 204260316343

371399427

68.965.862.461.4

59.658.357.2

4050 - 100

150200

1-1/22 - 4

68

BothBothBothBoth

to 427to 427to 427to 427

55.241.420.715.2

Level 4 Trim

WCC 29 to 371427

68.956.9

25 1CF8M

46 to 204260316371427

68.965.862.459.657.2

4050 - 100150200

1-1/22 - 468

BothBothBothBoth

to 427to 427to 427to 427

55.241.420.715.2


17/28


17

Flow Coefficients

Design BV500Forward Flow

Forward flow is in through the seat ring side of the valve.

Port VALVE ROTATION, DEGREES (LINE SIZE EQUALS VALVE SIZE)VALVE SIZE PortDiameter 10 30 60 10 30 60 10 30 60

DIN Inches mm Cv FL XT

Without Attenuator Disk -- Modified Linear Characteristic

DN 25 1

8.1212.7014.7318.29

0.50.91.42.3

1.42.84.27.0

2.85.68.4

14.0

0.950.950.940.88

0.940.930.930.87

0.930.930.920.86

0.5700.5800.6500.540

0.7400.7100.7200.630

0.7000.6900.6900.570

DN 40 1-1/2

12.7019.0523.1126.92

1.02.03.05.0

3.06.09.0

15.0

6.012.018.030.0

0.940.950.940.88

0.950.940.930.87

0.930.920.920.86

0.5200.5500.6000.520

0.7000.7100.6900.610

0.6800.6700.6600.560

DN 50 231.7539.62

5.56.6

19.021.0

30.045.0

0.940.87

0.930.86

0.920.86

0.470.47

0.670.56

0.560.57

DN 80 3

45.97

57.15

14.0

15.0

45.0

51.0

77.0

107

0.94

0.92

0.89

0.88

0.90

0.86

0.59

0.61

0.74

0.55

0.60

0.56

DN 100 458.6776.20

19.027.0

69.094.0

118177

0.940.92

0.880.87

0.880.85

0.670.49

0.690.57

0.610.58

DN 150 685.85101.60114.30

38.039.069.0

142167204

224310410

0.920.900.89

0.910.900.88

0.880.880.85

0.700.710.71

0.700.700.67

0.660.630.60

With Attenuator Disk

Cv FL XT

DN 50 231.7539.62

5.56.60

19.021.0

28.039.0

0.940.87

0.930.86

0.920.86

0.470.47

0.670.56

0.560.57

DN 80 345.9757.15

13.015.0

44.050.0

67.086.0

0.940.92

0.890.88

0.900.86

0.590.61

0.740.55

0.600.56

DN 100 458.6776.20

19.027.0

68.093.0

110162

0.940.92

0.880.87

0.880.85

0.670.49

0.690.57

0.610.58

DN 150 6 85.85101.60114.30

37.038.064.0

138162199

210281362

0.920.900.89

0.910.900.88

0.880.880.85

0.700.710.71

0.700.660.67

0.660.630.60

Conversions for Other Sizing Equations

Following are conversions for use with other common sizing equations

Kv = (0.865) CvC1 = 39.76 ( XT)Cg = CvC1Km = FL2Cs = 1/20 (Cg). Cs is only applicable for inlet pressure up to 70 bar (a).

Line-to-Valve Size Ratios Greater than 1-to-1

Contact your nearest sales office for information on determining the FP, the piping geometry factor.


18/28


18

Flow Coefficients (Continued)

Design CV500

VALVE ROTATION, DEGREES (LINE SIZE EQUALS VALVE SIZE)VALVE SIZE

10 30 60 90 10 30 60 90 10 30 60 90

DIN Inches Cv FL XTForward Flow

DN 80DN 100DN 150DN 200DN 250DN 300

3468

1012

4.7411.115.721.529.560.4

34.661.783.4156275443

1071933305929731390

166346809

144023603050

.85

.76

.93

.93

.93

.81

.84

.86

.81

.87

.91

.77

.86

.83

.74

.75

.77

.73

.69

.62

.57

.58

.54

.51

.294

.263

.281

.126

.537

.714

.511

.526

.311

.624

.566

.366

.559

.501

.459

.429

.316

.416

.372

.276

.221

.221

.152

.223

Reverse Flow

Cv FL XT

DN 80DN 100DN 150DN 200DN 250

DN 300

3468

10

12

3.257.205.208.6837.0

39.0

34.264.888.5156288

411

1292233726561080

1560

181300808

12402140

3080

.96

.98

.69

.77

.84

.71

.80

.84

.84

.87

.90

.80

.64

.65

.67

.66

.64

.63

.53

.61

.49

.58

.49

.50

.581

.463

.668

.898

.248

.975

.515

.526

.544

.585

.483

.533

.345

.334

.366

.354

.250

.325

.258

.308

.198

.260

.166

.196

Design V500 (Forward Flow)


10 30 60 90 10 30 60 90 10 30 60 90

DIN Inches Cv FL XT

Level 1, 2, and 3 Trims - Full Port

DN 25DN 40DN 50DN 80

11-1/2

23

1.222.074.118.80

5.0511.516.743.3

11.323.543.4116

12.226.646.2142

.89

.95

.97

.86

.88

.85

.84

.83

.85

.84

.75

.82

.85

.84

.74

.77

.480

.770

.439

.469

.508

.483

.442

.574

.632

.636

.462

.526

.593

.589

.442

.456

DN 100DN 150DN 200

468

16.617.551.5

79.1155298

203434775

2555651050

.85.97

.97.81.88.87

.79.73

.71.76.71.67

.439.879

.456.501.540.533

.490.432

.403.442.416.360

Level 1, 2, and 3 Trims - Reduced Port

Cv FL XT


11-1/2

23

.777

.6321.306.78

3.024.475.3116.0

4.9010.717.347.7

5.0110.917.348.4

.89

.84

.85

.90

.88

.84

.84

.87

.79

.75

.79

.82

.74

.73

.79

.77

.487

.559

.391

.487

.497

.522

.452

.487

.439

.508

.462

.429

.419

.490

.462

.429

DN 100DN 150DN 200

468

10.09.5039.9

24.441.8155

90.6170448

98.2200623

.95

.97

.96

.85

.92

.80

.81

.76

.76

.77

.74

.70

.426

.995

.400

.570

.403

.459

.462

.462

.413

.426

.410

.391

Level 4 Trim - Full Port

Cv FL XT

DN 25

DN 40DN 50DN 80

1

1-1/223

.300

1.461.767.60

4.68

8.1313.844.0

10.3

20.735.2102

11.6

25.038.4124

- - -

.86

.95

.88

.87

.82

.94

.85

.86

.80

.80

.82

.84

.79

.78

.80

.668

.566

.819

.578

.529

.555

.501

.511

.668

.574

.566

.515

.616

.597

.585

.526

DN 100DN 150DN 200

468

9.319.7134.6

73.5141290

171368716

221499958

.94

.95

.92

.85

.82

.78

.80

.78

.76

.77

.76

.73

.526

.504

.544

.449

.432

.426

.504

.436

.426

.487

.413

.429

Level 4 Trim - Reduced Port

Cv FL XT

DN 80DN 100DN 150DN 200

3468

4.122.2613.619.7

13.120.149.8134

39.069.1159438

48.090.1196605

.80

.96

.97

.93

.88

.85

.72

.76

.82

.83

.81

.77

.77

.74

.77

.72

.469

.779

.518

.597

.605

.632

.381

.422

.551

.589

.452

.381

.466

.452

.442

.436


19/28


19

Flow Coefficients (Continued)

Design V500 (Reverse Flow)


10 30 60 90 10 30 60 90 10 30 60 90

DIN Inches Cv FL XTLevel 1, 2, and 3 Trims - Full Port


11-1/2

23

1.081.712.987.19

5.2611.315.647.0

14.728.652.9122

16.831.057.4141

.80

.75

.92

.80

.73

.70

.81

.77

.55

.63

.58

.65

.48

.63

.58

.65

.172

.357

.480357

.406

.432

.462

.487

.322

.360

.265

.378

.283

.357

.265

.357

DN 100DN 150DN 200

468

12.215.133.5

79.9156302

202438798

235717986

.90

.85

.81

.81

.82

.79

.70

.66

.66

.69

.51

.66

.522

.416

.697

.487

.518

.483

.406

.388

.342

.416

.219

.363

Level 1, 2, and 3 Trims - Reduced Port

Cv FL XT


11-1/2

23

.634

.464

.9655.95

3.344.214.8214.7

5.6412.118.756.0

5.7612.218.956.7

.70

.93

.96

.80

.70

.75

.77

.73

.70

.70

.62

.58

.70

.70

.62

.58

.230

.970

.518

.429

.207

.501

.559

.487

.348

.416

.360

.286

.342

.416

.354

.281

DN 100DN 150DN 200

468

7.695.1027.1

22.734.6140

98.0170457

102232646

.83

.97

.92

.81

.90

.88

.59

.65

.66

.59

.55

.58

.504

.990

.636

.555

.566

.494

.322

.397

.388

.319

.258

.311

Level 4 Trim - Full Port

Cv FL XT


11-1/2

23

.107

.9881.427.64

5.097.6611.841.3

13.623.536.794.8

15.326.143.0111

- - -.98.97.93

.65

.75

.86

.89

.54

.58

.62

.72

.61

.61

.66

.76

.334

.473

.403

.616

.426

.563

.616

.537

.345

.403

.452

.508

.334

.429

.439

.511

DN 100DN 150DN 200

468

8.0710.525.4

67.1134266

153356686

192461897

.86

.80

.75

.84

.72

.75

.75

.69

.69

.74

.69

.72

.456

.511

.731

.533

.459

.483

.526

.397

.397

.515

.429

.426

Level 4 Trim - Reduced Port

Cv FL XT

DN 80DN 100DN 150DN 200

3468

4.41.97810.619.8

13.719.443.4125

53.367.8168413

57.986.6226569

.96.93

.77

.75

.93.89

.77

.78

.64.72

.64

.68

.63.65

.58

.70

.469.620

.640

.459

.578.593

.476

.462

.258.522

.357

.381

.268.436

.278

.391


20/28


20

Actuator-Valve Selection (Shutoff Pressure Drops)

Note

The intent of theactuator-valveselection tables is topresent an actuator

size that will controla relatively highvalve pressure dropwith a standardactuator operatingpressure. It is notimplied that theselection shown isbest for yourapplication.

For pressure dropslower than thoseshown, a lower

actuator pressure orsmaller actuatormight besatisfactory.

For pressure dropshigher than thoseshown, a higheroperating pressureor larger actuator willbe required.

Contact your salesoffice for other sizesand operatingpressures.

With rotary valves, the highestpressure drop occurs when thevalve is shut off. When the valveis open, pressure drop is normallymuch lower. However, pressuredrop capabilities of a rotary valvealso are lower when the valve isopen. The allowable flowingpressure drop across a valvedepends on the valveconstruction, on the type offlowing fluid (liquid or gas), andon the vapor pressure and criticalpressure ratio of liquids.

Only allowable shutoff pressuredrops are shown here. Todetermine the allowable flowingpressure drop, provide your salesoffice with the applicationinformation shown on page 23.

Do not exceed any other limitspresented in this flier. Following isa brief reminder of some of thoselimits:

Maximum Shutoff PressureDrop...Do not exceed any of thepressure drops in these tables orin the Maximum Allowable ShutoffPressure Drops section.

Maximum Inlet Pressure andTemperature...Do not exceed themaximum rating of the valve: PN10 through 100 or Class 150through 600. Refer to the BodyMaterials, End Connections, andRatings section.

Materials TemperatureLimits...Refer to the ValveMaterials and Temperaturessection, the actuatorspecifications tables, and theaccessories specifications tables.Some of the critical limits arerepeated here.

Temperature Summary

Minimum for all

Steel valve material DIN: 10_C

ANSI: 29_

CMinimum for alltypesStainless steel valve material DIN: 10_C

ANSI: 26_C

Design Packing Bearing - - -

PTFE 232_C

PROCESSPTFE

Metal 260_CPROCESSTEMPERATURE PTFE 232_C

MaximumCV500 and V500 Graphite

MetalCV500

316_C (260_Cwith CF8Mretainer)

V500 427_C

Nitrile 29 to 93_CO-rings for sealed bearing

Fluoroelastomer 18 to 204_C

Type 1051 and 1052 actuators 40 to 82_C with nitrile elastomers and 50 to 149_C with silicone

Type 1061 actuator 34 to 82_C (to 50_C with optional materials)AMBIENT TEMPERATUREType DVC5020 controller and

3610J Series positioners40 to 80_C

Minimum for all Steel valve material 29_CMinimum for alltypes Stainless steel valve material 196_C

Design Packing Guide Bushing - - -

Stainless Steel

PTFE Metal 232_C

PROCESS

PTFEPEEK/PTFE

232 C

PROCESSTEMPERATURE Stainless Steel

MaximumBV500

ENVIRO-SEALMetal 232_CBV500

PTFEPEEK/PTFE

232 C

Stainless SteelENVIRO-SEAL Metal 316_CGraphite

PEEK/PTFE316 C

AMBIENT TEMPERATURE 1052 actuators 40 to 82_C with nitrile elastomers and 50 to 149_C with silicone


21/28


21

Actuator-Valve Selection (Shutoff Pressure Drops)

Design BV500 (Forward Flow) with Type 1052 Actuator

SPRING-CLOSES (AIR-OPENS) SPRING-OPENS (AIR-CLOSES)

VALVE SIZE Actuator Pressure Pressure to Actuator Actuator Pressure Pressure to ActuatorVALVE SIZE ActuatorSize

PressureDrop, Bar Bar Psig

ActuatorSize


DN 25DN 40

DN 50

11-1/2

2

2020

33

51.751.7

51.7

2.32.3

2.3

3333

33

2020

33

51.751.7

51.7

2.32.3

2.3

3333

33DN 80DN 100DN 150

346

334040

21.7267.5

2.32.32.3

333333

334040

21.734.110.1

2.32.32.3

333333

Design CV500 (Forward Flow) with Type 1052 Actuator

AIR TO CLOSE (PUSH-DOWN-TO-CLOSE) AIR TO OPEN (PUSH-DOWN-TO-OPEN)BEARING

VALVE SIZE Actuator Pressure Pressure to Actuator Actuator Pressure Pressure to ActuatorMATERIALVALVE SIZE Actuator

SizePressureDrop, Bar Bar Psig

ActuatorSize


Type 1052 Actuator

DN 80DN 100DN 150

346

406070

41.441.421.2

0 to 2.30 to 1.20 to 2.3

0 to 330 to 180 to 33

606070

41.137.917.4

0 to 2.3 0 to 33

S44004DN 200DN 250

DN300

810

12

7070

70

10.24.6

2.4

0 to 2.3 0 to 337070

70

8.13.4

1.7

0 to 2.3 0 to 33

DN 80DN 100DN 150

346

406070

41.441.421.9

0 to 2.3 0 to 33607070

41.441.417.4

0 to 2.3 0 to 33

Alloy 6DN 200DN 250DN 300

81012

707070

8.44.62.4

0 to 2.3 0 to 33707070

8.13.41.7

0 to 2.3 0 to 33

PTFE/Compos-

DN 80DN 100DN 150

346

406060

41.441.424.5

0 to 2.3 0 to 33607070

41.441.419.0

0 to 2.3 0 to 33

ition LinedBearings

DN 200DN 250DN 300

81012

606070

10.75.23.1

0 to 2.3 0 to 33707070

8.33.82.3

0 to 2.3 0 to 33

Design CV500 (Forward Flow) with Type 1061 Actuator

Valve SizeActuator Pressure

Drop,Pressure to

Actuator ActuatorPressure

Drop,Pressure to

Actuator ActuatorPressure

Drop,Pressure to

ActuatorValve SizeSize

Drop,Bar Bar Psig

SizeDrop,Bar Bar Psig

SizeDrop,Bar Bar Psig

DIN Inches S44004 Bearings Alloy 6 Bearings PTFE/Composition-Lined Bearings

DN 80DN 100DN 150

346

304060

41.441.441.4

5.55.55.5

808080

304060

41.441.433.1

5.55.55.5

808080

404068

41.441.441.4

4.15.55.5

608080

DN 200DN 250DN 300

81012

688080

41.426.916.8

5.55.55.5

808080

6080100

15.226.926.1

5.55.55.5

808080

68100100

24.127.627.3

5.55.55.5

808080


22/28


23/28


24/28


24

Dimensions

Dimensions C and E (mm)

ActuatorType

ActuatorSize

C E

10513340

60

289333

473

338505

749

1052

2033406070

251289333473536

256338607876849

304060

171206267

378425406

10616880

100

324324381

483714714

Dimensions A and X for DesignCV500 and V500 (mm)

VALVE SIZE A (RAISED FACE)

DINANSI,Inches

DesignCV500

DesignV500

X

DN 25DN 40

DN 50

11-1/2

2

- - -- - -

- - -

102114

124

263272

288DN 80DN 100DN 150DN 200

3468

165194229243

165194229243

360364418466

DN 250DN 300

1012

297338

- - -- - -

639964

Dimensions for Design BV500 (mm)

DIMENSIONSVALVE SIZE Actuator SizeVALVE SIZE Actuator Size

A C E X


11-1/2

23

20203333

102114124165

251251289289

256256338338

258272278307

DN 100 4 40 194 333 607 406

DN 150 6 40 229 333 607 428

C

E

X

A


25/28


25

Ordering Information

When ordering, please specify ...

Application

Throttling or on-offType of Application

Reducing or relief

Include chemical analysisof fluid if possibleControlled Fluid

Specific gravity

Fluid Temperature

Minimum

Inlet Pressures Normal

Maximum

Minimum flowing

Normal flowing

Pressure Drops Maximum flowing

Maximum at shutoff

Minimum controlled

Flow Normal

Maximum

Maximum Permissible Noise Level, if Critical

Shutoff Classification Required

Line Size, Schedule, and End Connection Type

Valve, Actuator, and Accessories

From this or other product flier, select your choice whereever a choice is offered. If you cannot find the selection youneed, contact your nearest Fisher sales office.


26/28


26


27/28


27


28/28

Product Flier PF51.3:eplugFor Further Information, Contact...

AUSTRIAFisher-RosemountIndustrie - Zentrum No SudStrae 2a, obj M29A- 2351 Wr. NeudorfTelephone +43.2236.607Fax +43.2236.60744BELGIUMFisher-RosemountDe Kleetlaan 4B-1831 DiegemTelephone +32.2.716.77.11Fax +32.2.725.83.00BULGARIAProcess ControlTzarichina Str.1BG- 1505 SofiaTelephone +359.2.70.35.49Fax +359.2.75.91.43CISFisher-RosemountMalaya TrubetskayaStreet 8 - 11th floorCIS-119881 MoscowTelephone +7.095.232.69.68Fax +7.095.232.69.70CROATIAFisher-RosemountBerny CommerceZagorska 2710000 ZagrebTelephone +385.1.305.071.Fax +385.1.33.59.25CZECH RepFisher-RosemountVolsinch 75Cz- 100 97 Praha 10Telephone +420.2.810.026 66Fax +420.2.810.026.70DENMARK

Fisher-RosemountHejrevang 11DK-3450 AllerdTelephone +45 70253051Fax +45 70253052fisher-rosemount.dk

FINLANDOy Valmet-RosemountSinimaentie 10BFIN - 02630 EspooTelephone +358.9.523.500Fax +358.9.523.997FRANCE andMIDDLE EASTFisher-Rosemount2, place Gustave EiffelSilic 247

F- 94568 RungisTelephone +33.01.49.79.73.00Fax +33.01.49.79.73.99

GERMANYFisher-GuldeMannheimerstr. 63D-67071 LudwigshafenTelephone +49.0621.6811.0Fax +49.0621.6811.359GREECE

T.C.B.44, Pentelis str.GR-17564 Faliro-AthensTelephone +30.1.80.33.652Fax +30.1.80.33.819HUNGARYFisher-RosemountErsbet Kirlyn tja 1/cHu- 1146 BudapestTelephone +36.1.462.40.00Fax +36.1.343.01.73ITALYFisher-RosemountVia dell Artigianato 8/12I-20053 Muggi (Mi)Telephone +39.39.2.278.0590Fax +39.39.2.270.2302NETHERLANDSFisher-RosemountPatrijsweg 140NL-2289 EZ RijswijkTelephone +31.70.413.66.66Fax 31.70.390.68.15NORWAYSAAS SAPostboks 6500 EtterstadGrenseveien 95N- 0606 OSLOTelephone +47.22.63.57.00Fax +47.22.65.73.03POLAND

Fisher-RosemountAl. Wilanowska 272PL- 02665 WarszawaTelephone +48.22.85.73.766Fax +48.22.85.73.856PORTUGALFisher-RosemountRua Alfredo da Silva 8P-2720 AlfragideTelephone +351.01.471.28.850Fax +351.01.472.88.55ROMANIAFisher-Rosemount RomaniaCalea Floreasca No. 91-11BL. F1, Tronson 5. AP.44Sector 1RO-71401 BucharestTelephone +40.1.230.41.49Fax +40.1.230.05.01

SLOVAK RepFisher-RosemountHanulova 5/bSR- 84101 BratislavaTelephone +421.07.787.811Fax +421.07.787.245

SLOVENIA

MIRStrmeckijeva 16Sl-8270 KrskoTelephone +386.608.231.470Fax +386.608.231.471.

SPAINFisher-RosemountCtra Fuencarral-AlcobendasKm 12.2; Edificio Auge 1E-28049 MadridTelephone +34.1.358.91.41Fax +34.1.358.91.45SWEDENpeabIlanda Grd 120S - 65350 KarlstadTelephone +46.54.53.07.50Fax +46.54.53.18.51SWITZERLANDFisher-RosemountBlegistr. 21CH-6341 BaarTelephone +41.41.768.61.11Fax +41.41.761.87.40TURKEYFisher-RosemountProces KontrolKisikli CaddesiBasaran Ap. N_3 Kat281130 AltunizadeTR- skdarIstanbulTelephone +90.216.492.40.42-46Fax +90.216.492.40.47UKRAINEFisher-RosemountTereschenkovskaya St. 13,Rm. 58252004 KievTelephone +38.44.246.46.56Fax +38.44.246.46.58UNITED KINGDOM andMIDDLE EASTFisher-RosemountHorsfield WayBredburyStockport SK6 2SUUKTelephone +44.161.406.8826Fax +44.161.406.8827WEB site: www.fisher.com

FisherMarshalltown, Iowa 50158 USACernay 68700 FranceSao Paulo 05424 Brazil

Emerson Process Management

Cam-Vee-Ball, edisc, ENVIRO-SEAL, eplug, FIELDVUE, FloVue, Fisher, ValveLink and Vee-Ball are marks owned by Fisher Controls International, Inc. a business of EmersonProcess Management. The Emerson logo is a trademark and service mark of Emerson Electric Co. HART is a mark owned by the HART Communications Foundation. All other marks arethe property of their respective owners.

These products may be covered by one or more of the following patents: (4,519,579; 4,129,625; 5,131666; 5,056,757; 5,230,498; and 5,299,812) or under pending patents.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, t hey are not to be c onstrued as warranties or guarantees, express

or implied, regarding the products or services described herein or t heir use or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.

Documents

Brh Eplug Rotaryshaftvalves Ge