Upload
guven44
View
219
Download
0
Embed Size (px)
Citation preview
8/13/2019 DENACTIVE Brill Red Spe
1/4
1 / 4
MATERIAL SAFETY DATA SHEETDENACTIVE BRILL RED SPE
Document No: BUL.MSDS.66_en
Date of issue : 02.05.2012
Revision No: 0
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name DENACTIVE RED SPE
General Use REACTIVE DYESTUFF
Product DescriptionReactive Dyestuff CI. Reactive Red 223
Safety Signs
Company Identification
DENGE KMYA & TEKSTL SAN. TC. LTD. T.
Factory: erkezky Yolu zeri Akbayr Mevkii Velimee Ky 59850orlu TURKIYE
Phone: +90 (0282) 674 54 00 (pbx)Fax :+90 (0282) 674 50 01
Web: www.dengekimya.com
E-mail:[email protected]
2. COMPOSITION/INFORMATION ON INGREDIENTS
Component CAS No:
Denactive Red SPE80019-42-7
3. HAZARDS IDENTIFICATION
Emergency Overview Dark red powder that presents little or o immediate hazard. Avoid contact with skinand eyes.
Potential Health Effects
Inhalation Dust can be a nuisance. Based on similar products, material may cause
sensitization by inhalation.
Eye contact Non-irritating
Skin contact Non-irritating. Practically non-toxic in normal industrial use.
Ingestion Practically non-toxic in normal industrial use.
Chronic No known effects
4. EMERGENCY AND FIRST AID MEASURES
Ingestion If swallowed get medical attention.
Inhalation If exposure to dust causes irritation or distress, remove person to fresh air. Giveoxygen or artificial respiration if needed. Get medical attention.
Skin Contact Immediately flush skin with soap and plenty of water. Remove clothing
Wash clothing before reuse. Get medical attention.
Eye Contact Immediately flush eyes with plenty of water for at least 15 minutes and
contact a physician.
mailto:[email protected]:[email protected]:[email protected]:[email protected]8/13/2019 DENACTIVE Brill Red Spe
2/4
2 / 4
MATERIAL SAFETY DATA SHEETDENACTIVE BRILL RED SPE
Document No: BUL.MSDS.66_en
Date of issue : 02.05.2012
Revision No: 0
5. FlRE-FIGHTING MEASURES AND EXPLOSION HAZARD DATA
Flash Point Not known (Material is a powder)
Flammable limitNot applicable
Extinguishing mediaNon-flammable
Autoignition temperature About 300C
Special Fire-Fighting Measures: Not applicable
Explosion HazardsTo reduce potential explosion hazard, avoid dispersion of dust in air.
Hazardous decomposition
products:May generate SOx, NOxor CO when heated to burning
6. ACCIDENTAL RELEASE MEASURES
General Notify the appropriate authorities immediately. Take all additional action necessary toprevent and remedy the adverse affects of the spill.
Land Spill Collect in a dustless manner such as a vacuum cleaner or soak up with saw dust,then wash away any remaining traces. Prevent washings from entering waterways.
7. HANDLING AND STORAGE
PRECAUTIONS
Avoid breathing dust. Avoid contact with eyes. Avoid prolonged or repeatedcontact with skin. Use with adequate ventilation. May form explosive dust-airmixtures. Ground and bondcontainers when transfening material. Store at roomtemperature. Keep containers closed when not in use.
8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
Ventilation Use local ventilation at places where dust can be released into the workplaceair. Keep dust concentrations below recommended TLV.
ACGIH TLV for "Particles otherwise not classified"= 10mg/m3
Personal Protection:
Respiratory Not required for occasional handling if adequate ventilation is available.
A dust respirator is recommended for prolonged handling or exposure.
Protective Gloves Wear rubber gloves.
Eye Protection Wear safety goggles or equivalent eye protection.
Other Wear appropriate protective clothing to prevent skin contact.
Work/Hygenic Practices Always clean protective equipment and workplace.
8/13/2019 DENACTIVE Brill Red Spe
3/4
3 / 4
MATERIAL SAFETY DATA SHEETDENACTIVE BRILL RED SPE
Document No: BUL.MSDS.66_en
Date of issue : 02.05.2012
Revision No: 0
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance- Odor Dark Red Powderodorless
Melting Point Not known
Boiling Point Not known
Vapor Density Not Known
Percent Volatile Not applicaple
Vapour Pressure Not known
Evaporation rate Not applicable
pH 4,06,0 at 30 g/l water
Solubility > 100 g/l at 25C
Specific Gravity >0,45
10. STABILITY AND REACTIVITY
Stability Stable at normal condition
Conditions to avoid Avoid exposure to direct sunlight
Hazardous Decomposition
ProductsSee section 5
Hazardous Polymerisation Will not ocur
Incompatibility Oxidizing materials
11. TOXICOLOGICAL INFORMATION
Acute Inhalation Effects: No data available but similar products have caused sensitization and irritation.
Eye effects Non-irritant based on rabbits testing according to EEC standards
Skin Effects Non-irritant based on rabbits testing according to EEC standards
Acute Oral effects The oral LD50 in rats is > 2000 mg/kg
Chronic effects/Carcinogenicity No data available. Not listed by IARC, NTP or OSHA
12. ECOLOGICAL INFORMATION
No data available
13. DISPOSAL CONSIDERATIONS
May be incinerated by adequate methods. Disposal in accordance with federal, state
and local regulations. The owner of the material is responsible for proper waste disposal.
14. TRANSPORT INFORMATION
8/13/2019 DENACTIVE Brill Red Spe
4/4
4 / 4
MATERIAL SAFETY DATA SHEETDENACTIVE BRILL RED SPE
Document No: BUL.MSDS.66_en
Date of issue : 02.05.2012
Revision No: 0
Not regulated.
15. REGULATORY INFORMATION
To the best of our knowledge the substance:
is NOT listed on the black list 2455/2001/EG
It does NOT require labeling with any R phrases;; R27, 29, 35, 39, 40, 45, 46, 48, 49, 50, 51, 52, 53, 59, 60, 62, 63, 68
R phrases
R 22 Harmful if swallowed.
R 36/38 Irritate eyes and skin.
R 41 Causes dangerous and important irritation at eyes.
16. GENERAL INFORMATION
The information provided in this Material Safety Data Sheet is correct to the best of our knowledge, information and belief at thedate of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage,transportation, disposal and release and release and is not to be considered a warranty or quality specification. The informationrelates only to the specific material designated and may not be valid for such material used in combination with any othermaterials or in any process, unless specified in the text.