www.lighting.philips.com/dynalite

Leading Edge Dimmer Controller

Installation Instructions

Instructions d’installation

Installationsanweisungen

Instrucciones de instalación

Istruzioni per l’installazione

Installatie-instructies

インストール手順安装指示

DLE1205

RJ12

X 4

X 4

DLE1205 DLE1205-RCBO

X 4

176 mm (6.92 in)

620

mm

(24

.40

in)

221 mm (8.70 in)

255 mm (10.03 in)

60

0 m

m (

23

.62

in)

200 mm(7.87 in)

200 mm(7.87 in)

30 mm(1.18 in)

30 mm(1.18 in)

20

0 m

m(7

.87

in)

20

0 m

m(7

.87

in)

1

A B

40° C (104° F)

0° C (32° F)

≤95%

IEC Pollution Degree II

Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.

Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux.

Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren.

Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras.

I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici.

De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften.

装置を取り付ける際は、資格のある電気技師に依頼し、 国および地域の電気および建設に関するすべての法令に 従ってください。

根据国家/地区及当地的电气与建筑规范和法规，该设备必须由有资质的电工进行安装。

.

2

2 4

3 B

N

≤ 60 A≤ 5 A/CH

X

CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

CH9

CH10

CH11

CH12

≤ 5 mm2

10+ AWG

0.6 Nm5.5 Lb-in

≤ 5 mm2

10+ AWG

2.0 Nm17.7 Lb-in

≤ 5 mm2

10+ AWG

2.0 Nm17.7 Lb-in

3 A

3

ENL3

µP

L2L1

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 N N N N N N N N N N N N

AUX+12 V

D +D -

GNDSHLD

DMXRx

D -D +

-+

DyNetRS-485DMX Rx

2 x RJ12

12 V 1 A

SELV/Class 2

1 230 V ± 14% 60 A =3 230 /400 V ± 14% 3 x 20 A

12 V 200 mA

backup powerµP

5

L3

N

L2

L1

1

≤ 16 mm2

6+ AWG

1.4 Nm12.4 Lb-in

≤ 10 mm2

6+ AWG

2.0 Nm17.7 Lb-in

6 A 6 B

IEC Overvoltage Category III

L3

N

L2

L1

3

≤ 16 mm2

6+ AWG

1.4 Nm12.4 Lb-in

≤ 10 mm2

6+ AWG

2.0 Nm17.7 Lb-in

DyNet RS-485

+12V

+12V D

-D

+

GN

DG

ND

GND

GND

D+

D–

+12V

+12V

1

2

3

4

5

6

7 B

9

DyNet RS-485

8

0.4 Nm3.5 Lb-in

≤ 2.5 mm2

12+ AWG

GND AUX

<20 m

DyNet RS-485

SH

LD

GN

D

D+

D-

+12

V

AU

X

≤ 2 A

7 A

Apply de-rating for electronic and LED loads.

The manufacturer is not responsible for dimmable lamp selection. Each lamp/dimmer combination must be tested for compatibility prior to installation.

Professional dimmers rated > 1000 W are out of scope of EN 61000-3-2.

AZZ 488 0519 R13

© 2019 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.

www.lighting.philips.com/dynalite