Upload
others
View
40
Download
0
Embed Size (px)
Citation preview
B063
Milling Inserts & Tools
CXON / ONMX0505 ,SNMX1205
Brings a top performance in face milling operation
Economical machining achieved with Octagonal or Square shaped insert!! 以八角與四角型刀片達成最經濟的面銑加工效益 !!
.2 types of double sided inserts fit in the same pocket. (Octagonal & Square shaped).Single center lock screw for easy and rigid clamping ability. .High cutting edges strength and high efficiency machining for general purpose application.
RG
平面銑削
Face Milling
MG RG
.Octagonal insert ONMX0505 ( Total 16 cutting edges )
.Square insert SNMX1205 ( Total 8 cutting edges )
CXSN ,CXON / SNMX1205 ,ONMX0505
♦ ♦
Nickel contain plating applied for excellent corrosion resistance effect also increase surface hardness.To avoid the strain in second processing, finishing will be done after pre-harden.
Customize available.
CXSNF
Order No. D L d T ap InsertsScrew Wrench
ICXSNF04-050220 50 40 22 4 6
SNMX1205 TS4015 TK15
ICXSNF05-063220 63 40 22 5 6
ICXSNF05-063254 63 40 25.4 5 6
ICXSNF06-080270 80 50 27 6 6
ICXSNF06-080254 80 50 25.4 6 6
ICXSNF07-100320 100 50 32 8 6
ICXSNF07-100317 100 50 31.75 8 6
ICXSNF08-125400 125 63 40 10 6
ICXSNF08-125381 125 63 38.1 10 6
ICXSNF10-160400 160 63 40 12 6
ICXSNF10-160508 160 63 50.8 12 6
ICXSNF14-200476 200 63 47.625 14 6
ICXSNF14-200600 200 63 60 14 6
B064
ap
平面銑削
Face Milling
CXONF
Order No.D
L d T ap InsertsScrew WrenchON05 SN12
ICXONF04-050220 52.9 50 40 22 4 3
ONMX0505SNMX1205 TS4015 TK15
ICXONF05-063220 65.9 63 40 22 5 3
ICXONF06-080270 82.9 80 50 27 6 3
ICXONF07-100320 102.9 100 50 32 7 3
ICXONF07-100317 102.9 100 50 31.75 7 3Customize available.*ONMX0505and SNMX1205 insert can be used interchangeably on the CXON body.
Cutter will have different diameter, height and ap.
SNMX1205 ,ONMX0505
Working Material Vc fzap
SNMX1205 ONMX0505Carbon Steel (HB85-225) 80 ~ 200 0.10 ~ 0.30 ~ 6.0 ~ 2.0
Stainless 300 Series 50 ~ 110 0.08 ~ 0.25 ~ 3.6 ~ 1.5
Cast Iron (HB140-220) 80 ~ 180 0.10 ~ 0.30 ~ 6.0 ~ 2.0
Recommended Cutting Conditions
♦♦♦♦♦
Total 8 cutting edges per insert. (SNMX 1205)Total 16 cutting edges per insert. (ONMX 0505)Low cost effective and high efficiency for general purpose face milling.Low cutting force action due to the extremely positive geometry.Wide wiper flat for better surface finish.
B065
平面銑削刀片
Milling Inserts & Tools
Face Milling
SNMX 1205-MG ✓ ✓ ✓ 12.7 1.5 6.4 - 6 -
SNMX 1205-RG ✓ ✓ ✓ 12.7 1.5 6.4 - 6 -
P Steel ◎ ◎ ◎ ○ ○
1st choice 2st choiceM Stainless steel ○ ○ ○ ◎ ◎
K Cast iron ◎ ○ ○ ○ ○
Inserts Designation
Grade Dimensions (mm)
Drawing
CX21N
SC
X31NA
CX31N
SC
X41NS
CX41N
AA B S r d1 t1
Specification
ONMX 0505-RG ✓ ✓ ✓ 12.7 12.7 6.4 - 6 -