Fujitsu P1610 Lower Case

8/14/2019 Fujitsu P1610 Lower Case

1/9

LifeBook P1610Lower Ca se Rep la c ement

ESD Prec a utions a re req uired when wo rking o n this LifeBoo k co mp ute r.

Ma ke sure the LifeBoo k is turned off b efo re b eg inning this p roc ed ure.

1. Turn the LifeBook over a ndremo ve the b attery

3. Relea se the c a b le b y flipp ing thelatc h up.

2. Extra c t the se 3 sc rew s from theHa rd Disk Drive c ov er a nd lift it off.

4. Lift the Drive out.


2/9

5. Extra c t 11 sc rews from th e low ercase.

7. Op en the LifeBoo k a nd la y it fla t.

9. Lift the top ed ge of the keybo ardup a nd turn it over

11. Tilt the Disp lay up a nd rot a te it turn.

6. Extra c t 2 sc rews from th e rea r ofthe LifeBook.

8. Use a p lastic p ry too l to removethe keyboa rd up pe r trim.

10. Disc onnec t the keybo a rd a ndClickPoint c a b les from the systembo ard b y pulling them ge ntly.

12. Slide o ut the lowe r hinge c ove r.


3/9


4/9

21. Disc onne c t the IO Boa rd c a b le,the Bluetoo th ca ble, a nd the DCpo we r c a ble from the system b oa rd.

23. Extra c t 2 sc rews from the he a tsink and lift it o ut.

25. Disc onne c t the LAN ca b le fromthe system b oa rd .

27. Extra c t 2 he x sc rew s from theexternal VGA c onnec tor.

22. Disc onne c t the CPU fan c a b lefrom the system b oa rd .

24. Extra c t 3 sc rew s from the syste mb oa rd , lift it up a nd turn it ove r.

26. Extra c t 4 sc rews from t he IOBoard.

28. Lift the IO Boa rd a nd the RJ11c onnec tor out of the low er c ase.


5/9

29. Extra c t 1 sc rew from theBlueto oth b oa rd a nd lift it out.

31. Lift the external VGA c onne c torc over out of the lower ca se.

33. Extra c t 1 sc rew from t he PenCa tc h and lift it out.

35. Insert the stylus into its slot .

30. Lift the RJ45 c onne c to r a ndc ab le out of the low er c ase.

32. Press the stylus to relea se it a ndslid e it out .

34. Insert the Pen Ca tc h into th enew low er ca se a nd sec ure it with 1screw.

36. Insert the e xterna l VGAc onnec tor c over into the low er c ase.


6/9

37. Insert the RJ45 c on nec to r a ndc ab le into the lowe r c ase.

39. Insert the RJ11 Connec to r a nd IOBoa rd and sec ure the bo ard w ith 4sc rew s.

41. Set the syste m b oa rd o nto thelow er c ase a nd c onnec t the LANcable .

43. Pla c e the h ea t sink onto thesystem b oa rd a nd sec ure it with 2sc rew s.

38. Insert the Blueto ot h b oa rd a ndsec ure it with 1 sc rew.

40. Insert 2 he x sc rews into theexternal VGA c onnec tor.

42. Turn the syste m b oa rd o ver,insert it into t he low er c a se a ndsec ure it with 3 sc rews.

44. Conne c t the fan s c ab le to thesystem b oa rd .


7/9

45. Conne c t the IO Boa rd c ab le, theBluetooth c ab le, and the DC po werc ab le to the system b oa rd.

47. Plac e the upp er c ase a ndc onnec t the Clic kPoint butto n ca b leand the spe aker ca ble.

49. Extra c t 3 sc rew s from the PCB.

51. Atta c h the 2 d isp lay ca b les tothe system b oa rd and the 2 antennaCa b les to the WLAN ca rd .

46. Insert the WLAN ca rd a nd sec ureit with 1 sc rew .

48. Close the external VGAco nnector co ver and sec ure theup p er c a se with 4 sc rew s.

50. Sec ure the d isp lay with 2 sc rew sin the hinge .

52. Tilt the d isp lay up a nd rot a te it turn.


8/9

53. Slid e the low er hing e c over intoplace.

55. Plug in the c a b les for thekeyb oa rd a nd Clic kPoint.

57. Press the keyboa rd u p p er triminto place .

59. Insert 2 sc rew s into the rea r ofthe LifeBook.

54. Turn the Disp lay ba c k and lay itdown.

56. Turn the keyb oa rd o ver a nd slid eit into p la c e

58. Close the LifeBoo k and turn itover.

60. Insert 11 sc rews into the lowercase.


9/9

61. Insert the Ha rd Drive.

63. Rep la c e the Drive c ove r a ndsec ure it with 3 sc rew s.

62. Press the lat c h do wn to loc k theca ble into place.

64. Rep la c e the b a ttery.

Documents

Fujitsu P1610 Lower Case