FVC Nozzle 2

Pressure Vessel Connections• Long Welding Necks • Heavy Barrel Type HB Necks• Variable Body Type V1, V2, V3 Necks • Full Body Type F Necks• Studding Outlets • Custom Products • Rough Forgings• Insert Type “Q” Nozzles

Table of Contents

Introduction to FVC .................................................................................. 4FVC Standard and Variable Body Connections ......................................... 7

Introduction to Seamless Construction ................................................. 8LWN, HB, F, V1, V2, and V3:Class 150 ....................................................................................... 12Class 300 ....................................................................................... 16Class 400 ....................................................................................... 20Class 600 ....................................................................................... 24Class 900 ....................................................................................... 28Class 1500 ..................................................................................... 32Class 2500 ..................................................................................... 36

General Notes for FVC Connections .................................................... 40FVC Studding Outlets ............................................................................. 41

Introduction to Studding Outlets ........................................................ 42Class 150 ....................................................................................... 44Class 300 ....................................................................................... 45Class 600 ....................................................................................... 46Class 900 ....................................................................................... 47Class 1500 ..................................................................................... 48Class 2500 ..................................................................................... 49

General Notes for FVC Studding Outlets ............................................ 50FVC Custom Products ............................................................................. 53

Introduction to FVC Custom Product Capabilities ................................ 54Technical Section .................................................................................... 57Technical Table of Contents .................................................................... 58Warranty and Terms ............................................................................... 80

MAILING ADDRESS:

P. O. Box 38421Houston, TX 77238-8421

MAIN PLANT, DOMESTICAND INTERNATIONALSALES OFFICES:2525 DeSoto St.Houston, TX 770911-800-231-27011-713-688-9705FAX: 1-713-688-7954FAX: 1-713-688-7518FAX: 1-713-688-1846WEB PAGE:http://www.fvc.cc

E-MAIL:[email protected]

CANADA OPERATIONS:

WESTERN CANADIANSALES & DISTRIBUTION7410A-5 Street S.E.Calgary, Alberta T2H-2L91-800-382-34901-403-255-9011FAX: 1-403-255-7239E-MAIL:[email protected]

Forged Vessel Connectionsan AMERI-FORGE GROUP company

Studding Outlets

42

FVC studding outlets have many advantages whencompared to corresponding ASME B16.5 rated connections:1) a bolted style connection of significantly lower cost2) a lighter-in-weight bolted connection, requiring less material…the savings

in alloy construction are significantly higher3) a compact profile, thus providing lower projections for limited clearance

situations4) integral reinforcement…the outside diameter and/or overall thickness of

FVC studding outlets can be increased to eliminate the need for additionalreinforcement. This one-piece construction simplifies the welding required,thus reducing the cost of welding. Increasing labor costs are becoming amore significant part of finished product costs.

Studding Outlets

Remember, FVC provides custom design service for your special requirements,at no additonal cost. Please call FVC for your studding outlet needs.

43

There are many options available on FVC studding outlets,some of which include:1) contoured or flat bottoms…FVC can provide any degree of contouring to

suit your special mounting requirements2) air test holes as required by ASME Code…FVC can also provide test holes

to suit special customer requirements3) sight and light glass mounts…FVC can provide special machining of

studding outlets for your sight glass assemblies. A sketch of your individualrequirements is all that is needed.

4) contoured insert lips…FVC can provide contour forged or contourmachined insert lips for Type “Q” attachment as shown in ASME Sec. VIIIDiv. 1 Fig. UW16.1 or Div. 2 Fig. AD 613.1 requirements.

5) increased O.D. or thickness for additional reinforcement6) reduced O.D. or thickness when ASME B16.5 dimensions are not re-

quired… contact FVC to check your savings7) numerous special facings…please specify when ordering

Studding Outlets

Remember, FVC provides custom design service for your special requirements,at no additonal cost. Please call FVC for your studding outlet needs.

44

Outside R.F. Stud Hole Hole Stud Tap Tap Wall Approx.Size Dia. Thick. O.D. Holes Size Depth Circle Size T.P.I. Depth Thick. Weight

B O T R - - U C - - V - -

½ 3.50 1.25 1.38 4 27/64 0.88 2.38 1/2 13 0.56 1.50 3.05¾ 3.88 1.25 1.69 4 27/64 0.88 2.75 1/2 13 0.56 1.56 3.711 4.25 1.25 2.00 4 27/64 0.88 3.12 1/2 13 0.56 1.62 4.41

1¼ 4.62 1.25 2.50 4 27/64 0.88 3.50 1/2 13 0.56 1.69 5.161½ 5.00 1.25 2.88 4 27/64 0.88 3.88 1/2 13 0.56 1.75 5.962 6.00 1.50 3.62 4 17/32 1.12 4.75 5/8 11 0.75 2.00 10.08

2½ 7.00 1.50 4.12 4 17/32 1.12 5.50 5/8 11 0.75 2.25 13.543 7.50 1.50 5.00 4 17/32 1.12 6.00 5/8 11 0.75 2.25 15.05

3½ 8.50 1.50 5.50 8 17/32 1.12 7.00 5/8 11 0.75 2.50 18.884 9.00 1.50 6.19 8 17/32 1.12 7.50 5/8 11 0.75 2.50 20.545 10.00 1.75 7.31 8 21/32 1.31 8.50 3/4 10 0.88 2.50 27.556 11.00 1.75 8.50 8 21/32 1.31 9.50 3/4 10 0.88 2.50 31.418 13.50 1.75 10.62 8 21/32 1.31 11.75 3/4 10 0.88 2.75 44.07

10 16.00 1.81 12.75 12 49/64 1.44 14.25 7/8 9 1.00 3.00 59.2712 19.00 1.81 15.00 12 49/64 1.44 17.00 7/8 9 1.00 3.50 83.2514 21.00 2.00 16.25 12 7/8 1.56 18.75 1 8 1.12 3.50 103.3816 23.50 2.00 18.50 16 7/8 1.56 21.25 1 8 1.12 3.75 124.6618 25.00 2.25 21.00 16 1 1.81 22.75 1 1/8 8 1.25 3.50 141.6920 27.50 2.25 23.00 20 1 1.81 25.00 1 1/8 8 1.25 3.75 167.1324 32.00 2.50 27.25 20 1 1/8 2.12 29.50 1 1/4 8 1.44 4.00 245.14

CLASS

150 FVC Studding Outlets

Material: FVC forged studding outlets are made from SA-105 in compliance with ASME Section II. FVC studding outlets are available inother material compositions upon request. See “Technical Section” on page 59 for stocked materials.

Thickness: The standard thickness shown in charts for all FVC studding outlets is the minimum required per ASME Section VIIIDivision 1 Paragraph UG-43(d) for thread engagement and an l.D. mount (Fig. A, page 50). It is important to note that each individualapplication should be analyzed for proper thickness. See general notes for more details.

Facing: The FVC studding outlet minimum thickness “T” includes proper raised face per ASME B16.5. FVC can supply any specialfacing as needed upon request.

Notes continued on following page.

45


B O T R - - U C - - V - -

½ 3.75 1.25 1.38 4 27/64 0.88 2.62 1/2 13 0.56 1.62 3.53¾ 4.62 1.50 1.69 4 17/32 1.12 3.25 5/8 11 0.75 1.94 6.411 4.88 1.50 2.00 4 17/32 1.12 3.50 5/8 11 0.75 1.94 7.04

1¼ 5.25 1.50 2.50 4 17/32 1.12 3.88 5/8 11 0.75 2.00 8.101½ 6.12 1.75 2.88 4 21/32 1.31 4.50 3/4 10 0.88 2.31 12.822 6.50 1.50 3.62 8 17/32 1.12 5.00 5/8 11 0.75 2.25 11.80

2½ 7.50 1.75 4.12 8 21/32 1.31 5.88 3/4 10 0.88 2.50 17.923 8.25 1.75 5.00 8 21/32 1.31 6.62 3/4 10 0.88 2.62 21.39

3½ 9.00 1.75 5.50 8 21/32 1.31 7.25 3/4 10 0.88 2.75 25.064 10.00 1.75 6.19 8 21/32 1.31 7.88 3/4 10 0.88 3.00 30.855 11.00 1.75 7.31 8 21/32 1.31 9.25 3/4 10 0.88 3.00 35.446 12.50 1.75 8.50 12 21/32 1.31 10.62 3/4 10 0.88 3.25 44.158 15.00 1.88 10.62 12 49/64 1.44 13.00 7/8 9 1.00 3.50 63.53

10 17.50 2.12 12.75 16 7/8 1.56 15.25 1 8 1.12 3.75 91.0412 20.50 2.25 15.00 16 1 1.81 17.75 1 1/8 8 1.25 4.25 129.1414 23.00 2.25 16.25 20 1 1.81 20.25 1 1/8 8 1.25 4.50 154.9716 25.50 2.50 18.50 20 1 1/8 2.12 22.50 1 1/4 8 1.44 4.75 214.8718 28.00 2.50 21.00 24 1 1/8 2.12 24.75 1 1/4 8 1.44 5.00 250.9320 30.50 2.50 23.00 24 1 1/8 2.12 27.00 1 1/4 8 1.44 5.25 289.1924 36.00 2.88 27.25 24 1 3/8 2.38 32.00 1 1/2 8 1.69 6.00 453.48

FVC Studding Outlets

CLASS

300

Drilling and Tapping: FVC studding outlets are furnished to ASME B16.5 specifications unless otherwise specified. Thread depth is inaccordance with ASME Section VIII Division 1 Para. UG-43(g) for a design temperature not to exceed 650°F, a base metal stress of17,500 psi, and a stud stress of 25,000 psi. All other materials exceeding these stresses should be checked for UG-43 compliance.

Bore: Bore sizes shown above are standard, other sizes can be furnished upon request.

Curving: All FVC connections can be furnished contoured to fit any shell, head or cone at a minimal cost.

See pages 50 to 52 for complete general notes.

46


B O T R - - U C - - V - -

½ 3.75 1.50 1.38 4 27/64 0.88 2.62 1/2 13 0.56 1.62 3.79¾ 4.62 1.75 1.69 4 17/32 1.12 3.25 5/8 11 0.75 1.94 6.801 4.88 1.75 2.00 4 17/32 1.12 3.50 5/8 11 0.75 1.94 7.48

1¼ 5.25 1.75 2.50 4 17/32 1.12 3.88 5/8 11 0.75 2.00 8.661½ 6.12 1.94 2.88 4 21/32 1.31 4.50 3/4 10 0.88 2.31 13.092 6.50 1.75 3.62 8 17/32 1.12 5.00 5/8 11 0.75 2.25 12.71

2½ 7.50 2.00 4.12 8 21/32 1.31 5.88 3/4 10 0.88 2.50 19.063 8.25 2.00 5.00 8 21/32 1.31 6.62 3/4 10 0.88 2.62 22.88

3½ 9.00 2.12 5.50 8 49/64 1.44 7.25 7/8 9 1.00 2.75 28.104 10.75 2.12 6.19 8 49/64 1.44 8.50 7/8 9 1.00 3.38 41.165 13.00 2.25 7.31 8 7/8 1.56 10.50 1 8 1.12 4.00 63.546 14.00 2.25 8.50 12 7/8 1.56 11.50 1 8 1.12 4.00 70.038 16.50 2.50 10.62 12 1 1.81 13.75 1 1/8 8 1.25 4.25 102.14

10 20.00 2.75 12.75 16 1 1/8 2.12 17.00 1 1/4 8 1.44 5.00 170.2412 22.00 2.75 15.00 20 1 1/8 2.12 19.25 1 1/4 8 1.44 5.00 193.4814 23.75 2.88 16.25 20 1 1/4 2.25 20.75 1 3/8 8 1.56 4.88 218.5416 27.00 3.00 18.50 20 1 3/8 2.38 23.75 1 1/2 8 1.69 5.50 294.0518 29.25 3.25 21.00 20 1 1/2 2.56 25.75 1 5/8 8 1.88 5.62 358.4820 32.00 3.25 23.00 24 1 1/2 2.56 28.50 1 5/8 8 1.88 6.00 420.2824 37.00 3.75 27.25 24 1 3/4 3.00 33.00 1 7/8 8 2.12 6.50 625.81

CLASS






47


B O T R - - U C - - V - -

½ 4.75 2.00 1.38 4 21/32 1.31 3.25 3/4 10 0.88 2.12 8.28¾ 5.12 2.00 1.69 4 21/32 1.31 3.50 3/4 10 0.88 2.19 9.631 5.88 2.12 2.00 4 49/64 1.44 4.00 7/8 9 1.00 2.44 13.36

1¼ 6.25 2.12 2.50 4 49/64 1.44 4.38 7/8 9 1.00 2.50 15.111½ 7.00 2.25 2.88 4 7/8 1.56 4.88 1 8 1.12 2.75 20.082 8.50 2.12 3.62 8 49/64 1.44 6.50 7/8 9 1.00 3.25 27.40

2½ 9.62 2.25 4.12 8 7/8 1.56 7.50 1 8 1.12 3.56 36.913 9.50 2.12 5.00 8 49/64 1.44 7.50 7/8 9 1.00 3.25 33.194 11.50 2.50 6.19 8 1 1.81 9.25 1 1/8 8 1.25 3.75 56.225 13.75 2.75 7.31 8 1 1/8 2.12 11.00 1 1/4 8 1.44 4.38 92.786 15.00 2.50 8.50 12 1 1.81 12.50 1 1/8 8 1.25 4.50 91.88 18.50 3.00 10.62 12 1 1/4 2.25 15.50 1 3/8 8 1.56 5.25 172.59

10 21.50 3.00 12.75 16 1 1/4 2.25 18.50 1 3/8 8 1.56 5.75 224.6312 24.00 3.00 15.00 20 1 1/4 2.25 21.00 1 3/8 8 1.56 6.00 268.2114 25.25 3.25 16.25 20 1 3/8 2.38 22.00 1 1/2 8 1.69 5.62 298.3616 27.75 3.50 18.50 20 1 1/2 2.56 24.25 1 5/8 8 1.88 5.88 373.6818 31.00 3.88 21.00 20 1 3/4 3.00 27.00 1 7/8 8 2.12 6.50 520.1620 33.75 4.25 23.00 20 1 7/8 3.31 29.50 2 8 2.25 6.88 664.7124 41.00 5.12 27.25 20 2 3/8 4.00 35.50 2 1/2 8 2.81 8.50 1205.50


CLASS

900





48


B O T R - - U C - - V - -

½ 4.75 2.00 1.38 4 21/32 1.31 3.25 3/4 10 0.88 2.13 8.28¾ 5.13 2.00 1.69 4 21/32 1.31 3.50 3/4 10 0.88 2.19 9.631 5.88 2.12 2.00 4 49/64 1.44 4.00 7/8 9 1.00 2.44 13.36

1¼ 6.25 2.12 2.50 4 49/64 1.44 4.38 7/8 9 1.00 2.50 15.111½ 7.00 2.25 2.88 4 7/8 1.56 4.88 1 8 1.12 2.75 20.082 8.50 2.12 3.62 8 49/64 1.44 6.50 7/8 9 1.00 3.25 27.40

2½ 9.63 2.25 4.12 8 7/8 1.56 7.50 1 8 1.12 3.56 36.913 10.50 2.50 5.00 8 1 1.81 8.00 1 1/8 8 1.25 3.75 48.364 12.25 2.75 6.19 8 1 1/8 2.12 9.50 1 1/4 8 1.44 4.13 75.755 14.75 3.12 7.31 8 1 3/8 2.38 11.50 1 1/2 8 1.69 4.88 124.486 15.50 3.00 8.50 12 1 1/4 2.25 12.50 1 3/8 8 1.56 4.75 126.628 19.00 3.50 10.62 12 1 1/2 2.56 15.50 1 5/8 8 1.88 5.50 215.77

10 23.00 3.88 12.75 12 1 3/4 3.00 19.00 1 7/8 8 2.12 6.50 349.4712 26.50 4.12 15.00 16 1 7/8 3.31 22.50 2 8 2.25 7.25 485.0214 29.50 4.25 16.25 16 2 1/8 3.56 25.00 2 1/4 8 2.56 7.75 603.0816 32.50 5.00 18.50 16 2 3/8 4.00 27.75 2 1/2 8 2.81 8.25 849.6718 36.00 5.50 21.00 16 2 5/8 4.38 30.50 2 3/4 8 3.12 9.00 1140.9520 38.75 5.88 23.00 16 2 7/8 4.62 32.75 3 8 3.44 9.38 1386.0524 46.00 6.75 27.25 16 3 3/8 5.38 39.00 3 1/2 8 4.00 11.00 2233.80

CLASS






49


B O T R - - U C - - V - -

½ 5.25 2.00 1.38 4 21/32 1.31 3.50 3/4 10 0.88 2.38 10.22¾ 5.50 2.00 1.69 4 21/32 1.31 3.75 3/4 10 0.88 2.38 11.191 6.25 2.12 2.00 4 49/64 1.44 4.25 7/8 9 1.00 2.63 15.25

1¼ 7.25 2.25 2.50 4 7/8 1.56 5.12 1 8 1.12 3.00 21.891½ 8.00 2.50 2.88 4 1 1.81 5.75 1 1/8 8 1.25 3.25 29.642 9.25 2.25 3.62 8 7/8 1.56 6.75 1 8 1.12 3.63 34.68

2½ 10.50 2.50 4.12 8 1 1.81 7.75 1 1/8 8 1.25 4.00 49.443 12.00 2.75 5.00 8 1 1/8 2.12 9.00 1 1/4 8 1.44 4.50 75.924 14.00 3.25 6.19 8 1 3/8 2.38 10.75 1 1/2 8 1.69 5.00 121.335 16.50 3.75 7.31 8 1 5/8 2.81 12.75 1 3/4 8 2.00 5.75 194.056 19.00 4.12 8.50 8 1 7/8 3.31 14.50 2 8 2.25 6.50 281.778 21.75 4.38 10.62 12 1 7/8 3.31 17.25 2 8 2.25 6.88 378.47

10 26.50 5.12 12.75 12 2 3/8 4.00 21.25 2 1/2 8 2.81 8.25 655.4012 30.00 5.50 15.00 12 2 5/8 4.38 24.38 2 3/4 8 3.12 9.00 886.88


CLASS

2500





50

General Notes for FVCStandard Studding Outlets

Codes:Material and manufacturing practices for FVC studding outlets are in compli-ance with ASME Section II, Section VIII Division 1, and B16.5. Other re-quirements can be met when specified.

Materials:FVC forged studding outlets are made from SA-105 in compliance withASME Section II. FVC studding outlets are available in other material compo-sitions upon request. See “Technical Section” on page 59 for materialsstocked by FVC.

Thickness:The standard thickness shown in charts for all FVC studding outlets is theminimum required for ASME Section VIII Division 1 for thread engagementand thickness required for mounting the studding outlet to the I.D. as shown inFIG. A. It is important to note that for studding outlets which are set through avessel (FIG. A), the thickness of the studding outlet may need to be increasedto comply with ASME Code, Section VIII Division 1, paragraph UG-43(d)requirements. For studding outlets mounted to the O.D. as shown in FIG. B, areduction of thickness is possible. If the required minimum thickness is greaterthan FVC standard due to the ASME reinforcing requirements, FVC willincrease the studding outlet thickness as necessary at the buyer’s request orwhen design data is supplied with an order. The minimum thickness is mea-sured at the points in FIG. C and FIG. D.

Facings:All FVC studding outlets are furnished with a raised face per ASME B16.5. A0.06-inch raised face is provided on CLASS 150 and 300 flanges. A 0.25-inchraised face is provided on CLASS 400 and above flanges. These facing thick-nesses are included in the “T” dimension. See the “Technical Section” onpages 62 through 65 for other types of facings available on FVC flanges.Gaskets are not furnished by FVC.

Bolting and Tolerances:FVC flanges are furnished to ASME B16.5 specifications unless otherwisespecified. See the “Technical Section” on pages 60 and 61 for complete FVCtolerances.

Bore:Standard bores on all FVC studding outlets are to the nominal flange size.Larger or smaller bores can be provided on all FVC studding outlets uponrequest.

Notes continued on the following page.

51

Underside Curvatures:Unless otherwise specified, all FVC studding outlets will be furnished withflat bottom. Undersides of FVC studding outlets are furnished with a maxi-mum roughness of 500 microinches. This maximum roughness applies tocurved as well as flat bottom studding outlets.

When curving at the underside is required, it will be curved to fit flush on anI.D. mount (FIG. A) at the O.D. perimeter of the studding outlet. Whenmounted to the vessel I.D., some variation from a true radius may occur ontransverse centerline of cylindrical radius. The amount of variance will notexceed the maximum out-of-roundness tolerance per ASME Section VIIIDivision 1 paragraph UG-80. An outside shell mount (FIG. B) must be speci-fied by the customer as it requires special contouring.

When a “Wrap Around” configuration exists and the outside diameter of thestudding outlet exceeds the outside diameter of the shell to which it ismounted, the pad will be square as shown in FIG. E.

FVC studding outlets for hillside, inclined and conical locations will beprovided in the same manner as curvatures. There are no restrictions to theseverity of curvature which FVC can provide. Studding outlets requiring acurvature of less than 0.09 inch will be furnished flat, unless otherwise re-quested by the customer.

Drilling and Tapping:All standard FVC studding outlets are drilled and tapped unless otherwisespecified. The drilling and tapping is furnished in accordance with ASMEB16.5. The depth of tapping is in accordance with ASME Section VIII Divi-sion 1 paragraph UG-43(g). Stud holes will straddle centerlines, unless other-wise specified. Studs, nuts, inserts, and gaskets are not furnished by FVC.

Test Holes:Test holes can be provided on FVC studding outlets upon request. The testhole will be provided per FIG. F unless other specific details are supplied bythe customer with a 1/4” diameter drilling and a 1/8” N.P.T. tapping.

Pressure-Temperature Ratings:All standard FVC studding outlets are furnished in accordance with ASMEB16.5. See the “Technical Section” on pages 68 through 72 for rating chartsand notes regarding allowable design pressures and hydrotest pressures.

Notes continued on the following page.


52

Heat Treatment:All standard FVC connections CLASS 400 and above are supplied in thenormalized condition in accordance with the requirements of ASME SectionII. Additional heat treatment requirements can be furnished upon request.

Reinforcement:Particular attention must be paid to the area required for reinforcing an open-ing using a studding outlet because of the voids created by the tapped holes.Paragraph UG-37 of ASME Section VIII Division 1 addresses the planes ofreinforcement and the “F” factor. This reduction of available reinforcementmust not be overlooked. See the following table for area of various tappedholes. The area lost from the tapped holes can be provided by increasing the“T” dimension or the O.D. when required.

LOSS OF REINFORCEMENT DUE TO TAPPED HOLESTap Size (inches) Depth of Hole (inches) Area (sq. inches)

1/2 0.88 0.815/8 1.12 1.283/4 1.31 1.807/8 1.44 2.291 1.56 2.82

1 1/8 1.81 3.691 1/4 2.12 4.831 3/8 2.25 5.621 1/2 2.38 6.471 5/8 2.56 7.53 1 3/4 2.81 8.921 7/8 3.00 10.19

2 3.31 12.042 1/4 3.56 14.502 1/2 4.00 16.132 3/4 4.38 21.82

3 4.62 25.023 1/2 5.38 33.99


80

1. Any Sales Tax, Manufacturer’s Tax, or Use tax imposed by Federal, State or Municipal Law is to be addedto the prices and assumed by purchaser.

2. Seller is not responsible for delays, defaults, or damages occasioned by any causes beyond seller’s controlincluding, without limitation, governmental actions or orders, embargoes, strikes, fires and floods. In anyevent, partial deliveries shall be permitted at seller’s option.

3. Cancellations, of orders placed with and accepted by us, can be made only with our written consent. Uponrequest to cancel, we will advise amount of cancellation charges, in addition to charges for dies, work inprocess, products produced, including machine work, etc., and all liability for raw materials. Should youchange your material specification for your order after we have ordered or received the material, you are toassume all liability for the material covered by your initial specification.

4. It is understood that dies, tools, and patterns required to produce the article quoted on shall remain theproperty of FVC, Inc. Preparation charges or charges for dies, tools, and patterns represents only a portionof cost. Payment of such charge does not give you any right, title, or interest in such dies, tools, or otherproducts of preparation.

5. Purchaser represents that purchaser is solvent and can and will pay for products delivered to purchaser inaccordance with the terms hereof. However, seller retains the right to require full payment in advance if inseller’s sole discretion the financial position of the purchaser so requires.

6. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACEHEREOF EXCEPTING ONLY THAT EACH PRODUCT SOLD HEREUNDER IS WARRANTED TO BEFREE FROM MANUFACTURING DEFECTS, AND IF DEFECTIVE, WILL EITHER BE REPAIRED ORREPLACED WITHOUT CHARGE OR THE PURCHASE PRICE WILL BE REFUNDED, AT THE OP-TION OF SELLER. SELLER MAKES NO OTHER WARRANTY, EITHER EXPRESS OR IMPLIED.SELLER’S LIABILITY IS LIMITED TO THE SALE PRICE OF THE PARTICULAR PRODUCT. IN NOEVENT SHALL SELLER BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES OR FOR EXPENSEOCCASIONED BY THE USE OF DEFECTIVE PRODUCTS. SELLER’S LIABILITIES AS ABOVE SETOUT SHALL NOT BE EXTENDED BECAUSE OF ADVICE GIVEN BY SELLER IN CONNECTIONWITH THE DESIGN, INSTALLATION OR USE OF ANY PRODUCT. PURCHASER AGREES THAT IFTHE PRODUCTS SOLD HEREUNDER ARE BY PURCHASER RE-SOLD, PURCHASER WILL IN-CLUDE IN THE CONTRACT FOR RE-SALE, PROVISIONS WHICH LIMIT RECOVERIES AGAINSTTHIS SELLER IN ACCORDANCE WITH THIS PARAGRAPH.

7. Claims for shortages must be filed within ten days of receipt of shipment.8. We assume no responsibility if the manufacture and sale to you of the items specified by you is an infringe-

ment of patent rights of other persons, you assume responsibility for and will protect us from such infringe-ment liability, except as to our own manufacturing equipment and processes.

9. Stenographic or clerical errors are subject to correction.10. Deferred deliveries are subject to FVC, Inc. written approval.11. Purchases from us may not be returned without our written consent.12. These terms and conditions shall control in any contract resulting from or arising out of this quotation, price

sheet, or acknowledgement, regardless of printed terms, conditions or provisions found in responses heretoor documents giving rise hereto, all of such printed matters incorporated there in being deemed waivedinsofar as the same differ from these terms and conditions, unless such differing terms, conditions or provi-sions shall be specifically asserted for inclusion in written form other than printing and be specificallyaccepted by seller as a change in these terms and conditions by express reference in writing. The applicabil-ity of this paragraph is an express condition to any contract being formed between us.

13. Catalog product presentations including catalog dimensions, designs and specifications are representativeof product availability at time of publication only. Actual geometry dimensions and designs are subject todesigns and manufacturing changes without notice.

14. Material quoted as being available from stock is normally available for immediate shipment but subject toprior sale.

15. The above and foregoing terms and conditions are the final expressions of the terms and conditions of thecontract which may be or is formed between us and they are intended also as a complete and exhaustivestatement of the terms and conditions of such agreement.

16. All published prices are/or may be subject to a surcharge to customers, who, by reason of current or priortrade or business practices or course of dealings with FVC have increased or may increase marketing ordistribution costs.

FVC Terms and Warranty

Documents

FVC Nozzle 2