Upload
nguyennguyet
View
218
Download
1
Embed Size (px)
Citation preview
■ FTP-*A(PL・WO)-VD With relief valve(External-return)(VD)
Model examples:FTP-203A-VB (With valve (Internal-return)) FTP-204AR (Counter-clockwise as seen from the shaft end )
The 2A pump is for mid. capacity and mid. pressure. The max. flow rate and discharge pressure are 36L/min or less and 3MPa or less. For the applications of hydraulic pressure, lubrication and cooling, this pump is widely used to feed hydraulic oil and lubrication oil. A high temp. ver.(VF) and an ultra-high temp. ver.(VH) are up to 120℃ and 200℃, respectively. The standard rotation direction of this pump is counter-clockwise.
■ Standard and PL type
■ WO type■ FTP-*A(PL・WO)-VB With relief valve(Internal-return)(VB)
■ FTP-*A(PL・WO) Without relief valve
Key groovewidth
Key groovewidth
Key groovewidth
Key groovewidth
Key groovewidth
Key groovewidth
■ FTP-*A(PL・WO)R-VD With relief valve(Externall-return)(VD)
■ FTP-*A(PL・WO)R-VB With relief valve(Internal-return)(VB)
■ FTP-*A(PL・WO)R Without relief valve ■ Standard and PL type
■ WO type
No mark:StandardWO:Bunker oil, Coolant WaterPL:Liquid seal
No mark:StandardM:Dedicated motor (short shaft)
No mark:Standard (-5~80℃)
VF:Viton(R)for high temp. (120℃)
VH:Ultrahigh temp. (200℃)
No mark:No valveVB:With valve (Internal-return)
VD:With valve (External-return)
204206208210212216220
Model No. Applications Form
No mark:Counter clockwiseR:Clockwise
Rotation direction Seal material Relief valve
ex.0.1:Set pressure 0.1MPa(Spring No.1L)0.5:Set pressure 0.5MPa(Spring No.2L)1.0:Set pressure 1.0MPa(Spring No.3L)2.0:Set pressure 2.0MPa(Spring No.4L)
Relief valve set pressure
● Test conditions Oil:ISO-VG46 Oil temp.:40℃
● The required power varies depending on viscosity, temp. etc.
0.15.88.711.614.417.423.128.9
0.55.78.611.514.417.222.928.7
1.05.68.511.514.317.022.828.4
1.55.68.411.414.016.822.4ー
2.05.58.311.413.916.6ーー
2.55.48.211.313.8ーーー
3.05.3ーーーーーー
0.1668691
104123148205
0.5110158186210250308396
1.0169240305345405510633
1.5227329423480565715ー
2.0283415543615730ーー
2.5340497662749ーーー
3.0394ーーーーーー
204A206A208A210A212A216A220A
204A206A208A210A212A216A220A
0.50 0
200400600800
1000120014001600
05
1015
2025
30
35
05
10152025303540
100200300400500600700800900
1000
1.0 1.5 2.0 2.5 3.0 3.5 0.5 1.0 1.5 2.0 2.5 3.0 3.5
0.5 1.0 1.5 2.0 2.5 3.0 3.50.5 1.0 1.5 2.0 2.5 3.0 3.5
210A 210A
210A
210A
212A 212A
212A
212A
216A 216A
216A
216A
220A220A
220A
220A
206A 206A
206A206A
204A204A
204A204A
208A 208A
208A208A
0.17.0
10.414.017.621.027.834.8
0.56.9
10.313.917.520.927.734.6
1.06.8
10.213.817.220.627.434.3
1.56.7
10.113.817.020.427.0ー
2.06.7
10.013.816.920.2ーー
2.56.69.9
13.716.7ーーー
3.06.5ーーーーーー
0.180
104110125148179248
0.5133188225250302372478
1.0204290368413488616764
1.5274397510575681863ー
2.0342500655740881ーー
2.5410599800904ーーー
3.0476ーーーーーー
At 1,450 rotations (50Hz) At 1,750 rotations (60Hz)
■ Flow rate characteristics ■ Flow rate characteristics
Pressure (MPa)
Flow
rate
(L/
min
)
Pressure (MPa)
Flow
rate
(L/
min
)
Pressure (MPa)
Sha
ft po
wer
(W
)
Pressure (MPa)
Sha
ft po
wer
(W
)
■ Required power ■ Required power
Spec Flow rate (L/min) Required power (W)
Pressure (MPa) Pressure (MPa)Model
Spec Flow rate (L/min) Required power (W)
Pressure (MPa) Pressure (MPa)Model
Refer to these lines in the “Required power”table as applicable standards for theselection of a motor.
Refer to these lines in the “Required power”table as applicable standards for theselection of a motor.
Feature
Model
Dimensional diagrams/Standard rotation (mm)
Spec
Dimensional diagrams/Reverse rotation (mm)
Performance
Model
Model
Model
Model
Model Flow rate per. rev.(ml/rev)
Theoretical flow rate (L/min) Max. dischargepressure (MPa)
Max. revolution(min-1
)
Approx. weightWithout valve/With valve
(kg)1500min-1 1800min-1
Internal gear pump / 2A / Pump