TECHNICAL CATALOGUE - پتروشیمی جمEX5) ... Technical Cataloue 6 About JPC ... COMPONENT Unit SPECIFICATION Propylene % vol min 99.8 Propane …

TECHNICALCATALOGUE

2 0 1 7

About JPC

index:

6

12

20

24

38

Olefin Products

Chemical Products

HDPE Products

LLDPE Products

About JPCAbout JPC ................................................................................................. 6Vision, Mission, Values, Objectives............................................................. 9JPC in the Global Markets ..................................................................... 10

Olefin ProductsOlefin plant Capacity............................................................................... 14Ethylene................................................................................................. 15Propylene............................................................................................... 16Pyrolysis gasoline................................................................................... 17C4 cut..................................................................................................... 18Fuel oil.................................................................................................... 19

Chemical ProductsButadiene.............................................................................................. 22Butene-1................................................................................................ 23

HDPE ProductsProduct Capacity of HDPE plant............................................................... 26HF-4760(BL3)......................................................................................... 28HM-8355(BL4) ..................................................................................... 30HM-5010T2N (EX3) ................................................................................ 32HMCRP 100 N(PE100)........................................................................... 34HM CRP 100 Black................................................................................. 35HM9450F(EX5)....................................................................................... 36

LLDPE ProductsProduct Capacity of LLDPE plant............................................................. 4022502AA/22502KJ ................................................................................. 4322501AA/22501KJ ................................................................................ 44HP-LL18XF5/N ....................................................................................... 46HD5000s ............................................................................................... 4860505/UV .............................................................................................. 49HD-60507/UV......................................................................................... 5060511/UV............................................................................................... 51CC52501................................................................................................. 52CC52502................................................................................................. 54CC52502SU............................................................................................ 56HD-52505/UV......................................................................................... 5852511/UV............................................................................................... 60HD-52518............................................................................................... 624632604UV............................................................................................ 643838504UV ............................................................................................ 66

JAM Petrochemical CompanyTechnical Catalogue6

About JPCJAM Petrochemical Company (JPC) (private joint stock) was incorporated in 2000 along the lines of large scale programs of the country to exploit South Pars Gas Field. This huge industrial complex was constructed on the land of about 77 hectares in the South Pars Economic Zone situated in Asaluyeh, Bushehr. South Pars Gas Field, one of the biggest gas resources of the world, is located on the border shared with Iran and Qatar in the Persian Gulf, being 105 km to the south west of Asaluyeh Port. This Gas Field is extended over an area of 9,700 km2, of which 3,600 km2 is situated within Iranian waters. With approximately 14 trillion m3 gas, South Pars Gas Field accounts for 50 percent of the state’s gas reservoirs.

JAM Petrochemical CompanyTechnical Catalogue 7

After almost a decade of commissioning, this Gas Field with its olefin, linear low and high density polyethylene, butadiene and butene-1 continues to be one of the largest producers of olefin in the world and of polymer products in Iran. As the most distinguished productive complex in the South Pars Economic Zone, JPC produces and supplies various grades of petrochemical products in domestic and foreign markets. Constantly taking steps toward development, JPC is regarded as one of the most important petrochemical industrial complexes in the realm of economy. JPC production strategy, ceaseless improvement of value chain processes, customer orientation through the provision of high quality products and services as per international standards, and highly competent and committed personnel have been provided, and provides, this enterprise with endless and strong support for the achievement of its objectives and further allows it to continue to mount to the higher status in the world.



Vision

Mission

Values

Objectives

To turn into the biggest producerof olefin and its value chain in Iran up to 2021.

As a producer of olefin and its value chain, JPC relies on its capabilities and merits to create value for all beneficiaries for the ultimate purpose of improving human being quality of life globally.

• Being ambitious and seeking excellence;• Honoring human dignity;• Being knowledge oriented; and• Being accountable and responsible against beneficiaries.

1. Developing and completing the value chain of the production of olefin’s basic materials;

2. Enhancing flexibility and creating diversity in production of products tailored to the market needs;

3. Developing leadership relations and partnership with other enterprises to create higher value for JPC;

4. Constantly enhancing structures, systems, processes and managerial procedures so as to promote JPC’s productivity;

5. Designing and operationalizing integrated information management and knowledge management systems;

6. Utilizing the latest scientific and technological advances achieved all around the world for organizational training and excellence;

7. Ceaselessly creating value for clients and strengthening competitive advantages at the international level;

8. Institutionalizing and constantly improving our relationship with clients and other beneficiaries;

9. Continuously reinforcing moral values and attending to social responsibilities; and

10. Attracting, preserving, developing and employing human resources in a way consistent with JPC’s strategic requirements.

JPC in theGlobal MarketsJPC is among one of the largest exporters of Iranian polymer products. JPC continues to be ranked first for the export of high density polyethylene products. Eighty percent of JPC products are exported to more than 20 commercial destinations all around the world. One important market targeted by JPC is that of Chinese; however, JPC reduced its Chinese market share as part of its policies in order to abate commercial risks thereof. At the moment, China, Turkey, CIS, the Far East, European ports and neighboring countries serve as the entryway of JPC products to international markets. Africa and South America are another potential markets which are expected to allocated themselves a considerable part of JPC export. JPC endeavors to enhance its share of target markets and at the same time places great emphasis on potential markets.

1

Olefin Products


ApplicationsSaleable Products 1000 T/Y

Production Capacity1000 T/YProducts

Polyethylenee, PVC2201345Ethylene

Polypropylene20305Propylene

Feed for downstream plant265C4cut

To Aromatic Plant220216Pyrolysis gasoline

Feed for downstream plant2438Fuel Oil

For hydrogenation1.5Hydrogen

Fuel 3.9Methane

2174.4Total

Product Capacity of Olefin plant

Product data sheet


SPECIFICATIONCOMPONENT

vol % min99.9Ethylene

ppm vol max1000Methane + Ethane

ppm vol max500Ethane

ppm vol max5Acetylene

ppm vol max10C3 & Higher

ppm vol max2Carbon Monoxide

ppm vol max5Carbon Dioxide

ppm vol max10Water

ppm vol max5Oxygen

ppm vol max10Hydrogen

ppm vol max100Nitrogen

ppm vol max10Oxygenated Compounds

ppm vol max1 Basic Nitrogen CompoundeCaloulated as NH3

mg/kg max2Total sulphur

ppm vol max0.5Methanol

ppm vol max0.2Total Combined Nitrogen

ppm vol max0.02COS

ppm vol max0.3Mercaptans

Olefin made via Techinp Tecnology

Ethylene Is a simple olefin, the chemical formula is C2H4 has a prominent role in the petrochemical industry. It is colorless flamable gas.

Product data sheet



Propylene Also called propane, a colorless, flamable, gaseous hydrocarbon, C3H6, obtained from low molecular weight constituents of petroleum.

SPECIFICATIONUnitCOMPONENTmin 99.8% volPropylene

max 0.2 %% volPropanemax 5ppm volHydrogenmax 1ppm volEthylenemax 1ppm volButenesmax 1ppm volPentenes

max 20ppm volNon-condensablesmax 20ppm volEthanemax 10ppm volButane-pentanesmax 1ppm volC6-C12 Hydrocarbonsmax 1ppm volAcetylenemax 1ppm volMethyl-acetylenemax 1ppm volPropadiene

max 10ppm volButadienemax 2ppm volOxygen

max 0.03ppm volCarbon Monoxidemax 2ppm volCarbon Dioxide

max 0.02ppm volCOSmax 1ppm wtTotal sulphurmax 5ppm volMethanolmax 5ppm volIsopropanolmax 2ppm wtWater

max 0.01ppm volArsinemax 0.01ppm volPhosphine

max 1ppm wtAmmoniamax 0.05ppm volCyclopentadiene

Product data sheet



Pyrolysisgasoline

Pyrolysis gasoline, is a naphtha-range product with a high aromatics content used either for gasoline blending or as a feed stock for aromatics plants.

Analysis MethodSpec.UnitSPECIFICATIONmax 50 wt%Aromaticsmax 30wt%Benzene.………wt%Toluene

ASTM D40520.8-0.84gr/cm3Density at 15.6CASTM D86max 225.cFBPASTM D86min 33.cIBP

ASTM D637840-65kpaR.V.Pmax 21wt%Paraffinesmax 21wt%Isoparaffinesmax 2wt%Naphtenes

max 20wt%OlefinsASTM D5453350mg/kgTotal Sulfur

max 50 mg/100mlGum Contentmax 30ppbLead Content

ASTM E203.………Water Content.………wt%Unknown

ASTM D86.………wt%ResidueASTM D86min 45.c%5RecoveryASTM D86.……….c10%RecoveryASTM D86.……….c20%RecoveryASTM D86.……….c30%RecoveryASTM D86.……….c40%RecoveryASTM D86.……… .c50%RecoveryASTM D86.……….c60%RecoveryASTM D86.……….c70%RecoveryASTM D86.……….c80%RecoveryASTM D86min 175.c90%RecoveryASTM D86.……….cRecovery

-16Color Sybolt

Product data sheet


C4 Cut produced in Ethylene production planets by steam cracking of naphtha. It is a mixture of C4 hydrocarbons mainly 1,3- butadiens, Iso Butene, Butane.


C4 Cut

SPECITICATIONCOMPONENT45.1 %wt1,3-Butadiene0.12 %wtMethyl-Acetylene0.02 %wtPropadiene0.1 %wtPropylene

0.03 %wtPropane1.13 %wtVinyl-Acetylene19.2 %wti-Butene9.16 %wt1 Butene1.86 %wtCis2-Butene2.58 %wtTrans2-Butene3.94 %wti-Butane

16.56 %wtn-Butane0.06 %wtC5-diolefins0.1 %wtPentenes

0.02 %wtPentanes0.03 %wt2-methyl-butene

100.01 %wtTotal

Product data sheet



Fuel Oil Fuel oil product is a heavy hydrocarbon cut rich (poly) aromatic components.

VALUETEST/COMPOSITION

>60°CFlash point

approx. >40 cP at 80°CViscosity

2

ChemicalProducts

Product data sheet


Butadiene 1,3-Butadiene is a simple diene with the formula C4H6 . It is an important industrial chemical used as a monomer in the production of synthetic rubber.Annual production 115,000 tons

Butadiene made via BASF Tecnology

Analysis MethodSpecificationUnitAnalysis

ASTM D 2593Min. 99.4wt %1,3 - Butadiene

ASTM D 2593Max. 100wt ppm1,2 - Butadiene

ASTM D 2593Max. 0.5wt %Total Butenes

ASTM D 2593Max. 60wt ppmTotal Acetylenes

BASF's method50-200wt ppmTBC

ASTM D 2426Max. 0.1wt %Dimer (VCH)

BASF's methodMax. 5wt ppmPeroxides

BASF's methodMax. 0.1wt %Non Volatile Residue

ASTM D 5453Max. 5wt ppmTotal SulfurPORTABLE TRACE OXYGEN

ANALYZERMax. 0.2mol % Oxygen in Vapor Phase

Product data sheet


Butene-1 is a linear alpha-olefin with the formula C4H8 and used as a co-monomer for the production of HDPE & LLDPE and manufacturing of polybutene.Annual production 100,000 tons

Butene-1

Butene-1 made via Axense Tecnology

Analysis MethodSpecificationUnitAnalysis

ASTM D 4424Min. 99.5wt %Butene-1

ASTM D 4424Max. 100wt ppmC6+

ASTM D 4424Max. 0.5wt %C4s (Butenes + Butanes)

ASTM D 4424Max. 500wt ppmEthylene

ASTM D 4424Max. 100wt ppmEthane

ASTM D 4424Max. 15wt ppmAcetylenes

ASTM D 4424Max. 20wt ppm1,3-Butadiene

ISO 6381-1981Max. 1wt ppmCarbon monoxide

ISO 6381-1981Max. 1wt ppmCarbon dioxide

ASTM D 2029Max. 15wt ppmWater

ASTM D 5453Max. 1wt ppmTotal Sulphur

3

HDPE Products


DensityMFR

(190°C/2.16 kg)

PROPERTY

GRADES g/l(g/10 min).UNITISO 1183D 1238ASTM METHOD

17066INTERNAL METHOD1. INJECTION MOLDING

0.957±0.002

0.960±0.002

0.954±0.002

0.954±0.002

23±3

23±3

11±2

11±2

for transport and stacking bottle crates,particularty bottle createsfor transport and stacking bottle crates,particularty bottle createsfor thick walled highly stressed transport container,e.g. refuse bins and fish cratesfor thick walled highly stressed transport container,e.g. refuse bins and fish crates

HC 7260

HC 7260 *

HD 7255

HD 7255*

2. SMALL BLOW MOLDING

0.944±0.002

0.954±0.002

0.959±0.002+

1.1±0.3

1.2±0.3

1.5±0.3

for disinfectant bottles up to 2 liters, tubes for cosmetics, containers up to 10 liters and petrol cans up to 5 litersfor container with capacites ranging from a few ml up to 10liters , alsofor production of sheets for thermoformingfor hollow articles where high stress cracking resistance is not demanded,such as bottles and caisters up to 10 liters,e.g. for fabric softeners

HF 4750

HF 4760 (BL3)

HH 4765

3. LARGE BLOW MOLDING

0.951±0.0020.25±0.06general-purpose grade for large containersHM 8355

4. STRETCHED TAPE (RAFFIA)

0.944±0.002

0.944±0.002

1.8±0.3

1.8±0.3

stretched films and tapes for production of high-strength knitted and woventapes to be used for agricultural packagings and as protective cover

HF 7740 F

HF 7740 F2

5. MONOFILAMENT

0.956±0.0020.956±0.002

2.5±0.33.3±0.3

production of monofilaments with high tensile strengthmonofilaments for fishing notes , geo textiles and civil engineering

HF 7750 MHF 7750 M2

Available

Available

Product Capacity of HDPE plant


DensityMFR

(190°C/2.16 kg)

PROPERTY

GRADES g/l(g/10 min).UNITISO 1183D 1238ASTM METHOD

17066INTERNAL METHOD

6. CABLE

0.946±0.0023.5±0.5cable insulationHF 4750 K

7. PIPE(NATURAL/COLOR)

0.945±0.002

0.944±0.002

0.954±0.002

0.948±0.002

0.957±0.002

0.948±0.002

0.949±0.002

0.45±0.06

0.43±0.03

0.43±0.03

0.22±0.03

0.22±0.02

0.22±0.02

0.22±0.02

pressure pipes, e.g. drinking-water and gas pipes,waste pipes and sewer pipes,their fittings and also sheets(UV stabilization and pigments during processing)high-quality PE 80 pressure pipes for gas and water transportation(UV stabilization and pigments during processing)high-quality PE 80 pressure pipes for gas and water transportation(UV stabilization and pigments during processing)top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)top quality PE 100 pressure pipes for gas and water transportation at higher pressures or with thinner walls as PE 80 (UV stabilization and/or pigments during precessing)

HM 5010 T2 N

HM 5010 T3 N

HM 5010 T3 Black

HM CRP 100 N

HM CRP 100 Black

HM CRP 100 Blue

HM CRP 100 O/Y

8. FILM

0.956±0.002

0.949±0.002

0.950±0.002

0.957±0.002

0.944±0.002

0.28±0.05

0.28±0.05

0.22±0.05

0.22±0.05

0.18±0.03

for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing and sealabilityfor blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing for blown films with paperlike quality,suitable for counter bags,carrier bags and wrapping films,excellent processing

HM 9455 F

HM 9450 F

HM 9450 F1

HM 9455 F1

HM 9445 HT

Available

Available

Available

Available

Product Capacity of HDPE plant


Product data sheet

HDPE: HF-4760(BL3) MFR 190/5: 0.9-1.5

CharacteristicProperties

• High density and Stiffness, good flowabilitty and impact Strenght

and good Stress Cracking resistance.

Main Applications

• For container with capacities rang-

ing from a few ml up to 10 liters, also

for production of sheets for thermo-

forming.

Additives

• Antioxidant/Process stabi-

lizer

• Lubricant/ acid scavenger

HDPE made via Hostalen Process

HF-4760(BL3)

Material properties (This data are typical values and are not to be construed as product specifications.)

Test MethodTypical ValueUnitResin PropertiesISO 113323(g/10 min)Melt Index(21.6)ISO 11331.2(g/10 min)Melt Index(5)

19 FRR (21.6/5)ISO 11830.954g/cm³Density

Test MethodTypical ValueUnitMoulded PropertiesISO 179/ 1 eA9mJ/mm²Notched Impact @ 23 °C

Density: 0.942-0.956 g/cm3

HF-4760 (BL3) is a blow molding grade resin which is manufactured by suspension polymerization of ethylene monomer. HF-4760 (BL3) is a bi-model high density polyethylene with 1-Butene as co monomer.

29


Shear-Viscosity @ 190 °C

- On compression moulded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.

The above values wereCalculated from data for 100 µm producedon a 75mm Barrnageextruder with 190°C melt tem-perature using a 2:1 blow ratio and a gap die of 3.0 mm.

Handling and Health SafetyMolten polymers could be injured skin or eye so safety glass-

es and appropriate gloves are suggested to prevent possible

thermal injuries. Also appropriate ventilation is suggested in

working by melt polymer.

Accumulation of fines or dust particles that are in this grade

is not suitable because of explosion hazard probability. So

adequated filters and grounding exists at all time are rec-

ommended.

Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ul-traviolet cause a change in the material properties.The Stor-age area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.

packagingJam Polymers Polyolefin resins are supplied in Pellet form packed in 25kg bags. Alternative packaging modes are aval-able for selected grades.


Product data sheet

HM-8355(BL4) is a Blow molding grade resin which is manufactured by suspension polymerization of ethylene monomer. HM-8355 (BL4) is a bu-modal high density polyethylene with Butene-1 as co monomer with general purpose of large container.

Density: 0.949-0.953 g/cm3HDPE: HM-8355(BL4) MFR 190/5: 0.29-0.41


• High molar mass, easily process-

able high stiffness strenght, good

stress Cracking resistance and very

good molding surface finish.

Main Applications

• General purpose grade for large

container.

Additives


lizer

• Lubricant/ acid scavenger


HM-8355(BL4)


Test MethodTypical ValueUnitResin PropertiesISO 11339.5(g/10 min)Melt Index(21.6)ISO 11330.35(g/10 min)Melt Index(5)


110%Swell RatioTest MethodTypical ValueUnitMoulded PropertiesISO 179/ 1 eA10mJ/mm²Notched Impact @ 23 °C

31












ommended.




Product data sheet

HM-5010T2N (EX3) is a pipe grade resin which is manufactured by the suspension polymerization of ethylene monomer. HM-5010T2N (EX3) is a bi-model high density polyethylene with 1-Butene as co monomer.

Density: 0.943-0.947 g/cm3HDPE: HM-5010T2N (EX3) MFR 190/5: 0.39-0.51


• Tough and rigid pipe resin.

Main Applications

• Pressure pipes, e.g. drinking-water and gas pipes, waste pipes and sewer pipes, their fittings and also sheets (UV stabilization and pigments during processing)

Additives


lizer

• Lubricant (processing aid)/

acid scavenger


HM-5010T2N(EX3)


Test MethodTypical ValueUnitResin PropertiesISO 113312(g/10 min)Melt Index (21.6)ISO 11330.45(g/10 min)Melt Index (5)


Test MethodTypical ValueUnitMoulded PropertiesISO 179/ 1 eA12mJ/mm²Notched Impact @ 23 °CTest MethodTypical ValueUnitMechanical Properties

ISO 1167(4.0 N/mm²) 1000hHydrostatic Strenght (80 ºC)

33










ommended.





Product data sheet


-M-CRP100N (PE100) is a natural pipe grade resin shich is manufactured by suspension polymerization of ethylen monomer, HM-CRP100N )PE100) is a bi-model high density polyethylene with 1-Butene as co monomer.

Density: 0.946-0.950 g/cm3HDPE: HMCRP 100 N (PE100) MFR 190/5: 0.19-0.25


• Natural PE100 pipe resin.

Main Applications

• Top quality PE100 pressure

• Pipes for gas and water transpor-

taion at higher pressures or with

thinner walls as PE80 (UV stabilization

and/ or pigments during precessing)

Additives

• Antioxidant/Process stabilizer

• Lubricant (processing aid)/ acid

scavenger


HMCRP 100N(PE100)


- Test specimen from compression moulded sheet at 23°C.- FRR values are statistical and calculated by dividing MFR values.- Notch Impact Test specimen from compressed moulded sheet 23°C and The data quoted are average values .

ASTM MethodUnitTypical ValueTest/CompositionISO1183g/ml30.948Density

28FRR 21.6/5ISO1167h5000 (4.5N/mm2)Hydrostatic Strength (80°c)ISO1133(g/10 min)6.2MFR190°/21.6ISO1133(g/10 min)0.22MFR190°/5

ISO179/1eAmJ/mm224Notched Impact (23°c)

Product data sheet


HM-CRP100 Black is a black pipe grade resin (PE100) which is man-ufactured by suspension polymerization of ethylene monomer. HM-CRP100 Blue is a bi-model high densit polyethylene with 1-Butene as co monomer.

Density: 0.955-0.959 g/cm3HDPE: HM CRP 100 Black(PE100 Black) MFR 190/5: 0.20-0.24


• Black PE100 resin

Main Applications

• Top quality PE100 pressure pipes for gas and water transportation at higher pres-sures or with thinner walls as PE80

Additives


• Lubricant (processing aid)/

acid scavenger

• Carton Black


HM CRP 100 Black


- Test specimen from compression moulded sheet at 23°C.- FRR values are statistical and calculated by dividing MFR values- Test specimen from compressed moulded sheet 23 C sheet 23 ºC - The data quoted are average values - The data quoted are average values

ASTM MethodUnitTypical ValueTest/CompositionISO1183g/ml30.947Density

28FRR 21.6/5ISO1167h5000 (4.5N/mm2)Hydrostatic Strength (80°c)ISO1133(g/10 min)6.2MFR190°/21.6ISO1133(g/10 min)0.22MFR190°/5

ISO179/1eAmJ/mm224Notched Impact (23°c)

Product data sheet


HM-9450F (EX5) is blown film grade resin which is manufactured by suspension polymerization of ethylen monomer. HM-9450F (EX5) is a bi-model high density polyethylene with 1-Butene as co monomer.

- Test specimen from compression moulded sheet at 23°C.- FRR values are statistical and calculated by dividing MFR values.- Notch Impact Test specimen from compressed moulded sheet 23°C and The data quoted are average values

Density: 0.947-0.951 g/cm3HDPE: HM9450F (EX5) MFR 190/5: 0.23-0.33


• High molar mass film grade, good

stiffness and tenacity

Main Applications

• For blown films with paperlike qual-

ity, sutable for counter bags, carrier

bags and wrapping films, excellent

processing.

Additives


• Lubricant (processing aid)/ acid

scavenge


HM9450F(EX5)


Test/Composition Typical Value Unit MethodDensity 0.949 g/cm3 ISO1183Fish Eye Note ≤3 note InternalFRR 21.6/5 29MFR 190°/21.6 8.0 g/10min ISO1133MFR190°/5 0.28 g/10min ISO1133

4

LLDPE Products


Product Capacity of LLDPE plant

DensityMFR

(190°C/2.16 kg)

PROPERTY

GRADES g/l(g/10 min).UNITD 1505D 1238ASTM METHOD1700417066INTERNAL METHOD

1- LLDPE Butene

922 - 925918 ± 2923 ± 1923 ± 1918 ± 2

916 - 919

0.70 ± 0.10.95 ± 0.11.80 ± 0.20.95 ± 0.12.00 ± 0.23.00 ± 0.3

LaminationLinerGeneral PurposeHigh StiffnessCast & general PurposeCast

235F71650122502/ AA/ 22502 KJ22501/ AA/ 22501 KJ1650216503

2- Terpolymer - HP-LLDPE SPECIALITY PRODUCTS

914 ± 2914 ± 2

914 - 917914 - 917914 ± 2915 ± 1912 ± 1910 ± 1921 ± 1920 ± 2

0.60 ± 0.100.6

0.75 ± 0.100.90 ± 0.100.95 ± 0.100.95 ± 0.102.00 ± 0.202.20 ± 0.202.50 ± 0.200.50 ± 0.10

High PerformanceShrinkEasy ProcessabilityLaminationSuperbuteneHigh StiffnessGeneral PurposeStretch castBread bagsHigh performance

12XF612HF614ZF814XF912X0114X0111X0209X0220X0218XF5 N

3- Quattropolymer'' HP-LLDPE SPECIALTTY PRODUCTS (HP HEXENE TYPE)

918 - 921918 - 921914 ± 2916 ± 1

911 - 914915 ± 1911 ± 1

0.30 ± 0.050.55 ± 0.100.60 ± 0.100.60 ± 0.100.60 ± 0.101.00 ± 0.102.20 ± 0.20

Shrink film, high perform.High Stiffness/ ShrinkLinerHeavy dutyLamination high clarityThin filmHigh Pre-Stretch cast

18YF318YF512YF615YF611YF614Y0110Y02

4- VLDPE (butene) film grades SPECLALITY GRADES

911 ± 1911 ± 1

2.50 ± 0.302.50 ± 0.30

LaminationCast- Co-extrusion(*)

1050110502

(*) This product is used as adhesive layer in a multilayer co-extruded film.

Available

Available

Available



DensityMFR

(190°C/2.16 kg)

PROPERTY


5- HP-VLDPE SPECIALITY PRODUCTS

902 ± 1903 ± 1

0.90 ± 0.101.80 ± 0.20

Co-extrusionGeomembranes, Bumpers, Soft Nets

01X0102X026- HDPE - Medium MWD - Stretched

954 ± 1942 ± 1953 ± 1950 ± 2

0.80 ± 0.100.50 ± 0.100.70 ± 0.101.00 ± 0.10

MonofilamentRaffia (Textile grade)Monofilament, high tenacityMonofilament

Jamlene HD-5000s424F5534F750401

7- HP-HDPE (@) SPECIALITY PRODUCTS

936 ± 1943 ± 1941 ± 1

0.60 ± 0.101.00 ± 0.101.20 ± 0.10

Raffia for ropesMonofilamentCast flat yarn (Raffia)

36XF643X0141X01

8- HDPE Narrow MWD - Homopolymer injection moulding grades

958 ± 2958 ± 2958 ± 2958 ± 2958 ± 2

5.50 ± 1.007.50 ± 1.0011.00 ± 2.0018.00 ± 2.0035.00 ± 5.00

CratesCratesHousewareFast cycleThin walled

60505 / 60505 UV60507 / 60507 UV60511 / 60511 UV6051860535

9- HDPE Narrow MWD - Copolymer injection moulding grades

952 ± 2952 ± 2952 ± 2952 ± 2952 ± 2952 ± 2952 ± 2

0.90 ± 0.102.00 ± 0.102.00 ± 0.105.00 ± 1.0011.00 ± 2.0018.00 ± 2.0028.00 ± 4.00

Caps and closures (CSD)Caps and closures (Mineral water, CSD)Caps and closures (CSD)ContainersHousewareHouseware, High fluidityCaps, Thin walled

CC 52501CC 52502CC 52502SU52505 / 52505 UV52511 / 52611 UV5251852528

10- LLDPE (butene) Injection moulding grades

922 ± 1922 ± 1925 ± 1926 ± 1

5.00 ± 1.0016.00 ± 2.0025.00 ± 3.0060.00 ± 5.00

General purposeGeneral purposeLidsFast Cycle

20505205162552526560

New

New

New

New

Available

Available

Available

Available

Available

Available

Available

Available

Available

Available



DensityMFR(190°C/2.16 kg)PROPERTY


11- LLDPE (butene) Extrusion coating

923 ± 17.00 ± 1.00Extrusion coating23507

12- LLDPE Rotomoulding

932 ± 1930 ± 1938 ± 2

932

4.00 ±1.005.00 ± 1.004.00 ± 1.00

5

Rotomoulding, high-ESCRRotomoulding, high-ESCRRotomoulding, high-ESCRRotomoulding, high-ESCR

32604 UV30505 UV38504 UV32505 UV

13- HP LLDPE SPECIALTTY PRODUCTS

930 ± 14.00 ± 1.00Rotomoutding & Stiff Cast30Y04

14- BWMD HDPE for Blow moulding

952952952

0.120.250.25

Blow moulding containers, high impactBlow moulding small containers, high ESCRBlow moulding small containers

526F1BX(*)

526F2BX524F2(*)

15- BWMD HDPE for pipes

9480.2(1)Pipes486H2(*)

16- BWMD HDPE for Blown film

952948952948

0.15(1)

0.25(1)

0.15(1)

0.25(1)

Blow film, high StiffnessBlow film, high mechanicalsBlow film, high StiffnessBlow film, general purposes

526H1(*)

486H2(*)

524H1FX(*)

484H2(*)

(*) Grade under final development, to be Industrialised.

(1) Melt Flow rate (190° C/5kg).

Available

Available

Product data sheet


22502 is a LLDPE blown film grade designed for applications requiring ease of processing and good optical properties even at low extrusion temperature. This resin is well suited for blending with LDPE and for general purpose uses, including agricultural applications.

Density: 0.922-0.924LLDPE: 22502AA/22502KJ MFI: 1.6-2


• ease of processing• good optical properties• low extrusion temperature• suited for blending with LDPE

Main Applications

• Blown film grade• General purpose• agricultural applications.

22502AA/22502KJ


LLDPE made via Spherilene Gas-Phase Technology

ASTM MethodTypical ValueUnitResin PropertiesD12381.80(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.9220g/mlDensity

Film properties @D170967(g)Dart ImpactD1922127/332MD/TD(g)Elmendorf TearD88212/12MD/TD(MPa)Tensile strenght at yieldD88237/32MD/TD(MPa)Tensile strenght at breakD882783/888MD/TD(%)Ultimate elongation

D100348(%)HazeD245710Gloss 45°

@ 25 micron film obtained on Collin 25, B.u.R. 2.5: 1, Temp. profile 155 190°C.Recommended processing conditions

190-230(°C)Melt Temperature2.0-3.0Blow up ratio2.0-2.5(mm)Die Gap15-150(micron)Thickness

Additives

• 22502AA:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• 22502KJ:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Slip Agent• Catalyst neutralizer (acid scavenger, lubricant)


Product data sheet

22501 is a LLDPE blown film grade designed for applications requiring good optical properties even at low extrusion temperature. This resin combines ease of processing with low gels and it is well suited for blending with LDPE and for general purpose applications.

Density: 0.922-0.924 LLDPE: 22501AA/22501KJ MFI: 0.85-1.05


• High stiffness• good optical properties• low extrusion temperature• ease of processing• low gels• suited for blending with LDPE

Main Applications

• Blown film grade• General Purpose opplications

Additives

• 22501AA:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• 22501KJ:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Slip Agent• Catalyst neutralizer (acid scavenger, lubricant)

22501AA/22501KJ


LLDPE made via Spherilene Gas-Phase Technology


Film properties @D170970(g)Dart ImpactD1922105/436MD/TD(g)Elmendorf TearD88211/12MD/TD(MPa)Tensile strenght at yieldD88241/31MD/TD(MPa)Tensile strenght at breakD882648/780MD/TD(%)Ultimate elongation

D100348(%)HazeD245710Gloss 45°

@ 25 micron film obtained on Collin 25, B.u.R. 2.5: 1, Temp. profile 155 190°C.Recommended processing conditions

190-230(°C)Melt Temperature2.0-3.0Blow up ratio2.0-2.5(mm)Die Gap15-150(micron)Thickness

45












ommended.




Product data sheet

HP-LL18XF5 N is a termopolymer of ethylene, propylene and butene-1 for high strenght application especially heavy duty shipping sacks, ice bag, frozen food bags, potato bags and agriculture films which have good sealability and excellent puncture resistance. Goods produced from this grade have outstanding toughness, excellent puncture resistance, good heat sealing behavior and excellent machinability on conversion lines. HP-LLDPE's process is easier than conventional LLDPEs and have low gel. HP-LL18XF5 N is a grade without slip additives.

Density: 0.918-0.922HP-LLDPE: HP-LL18XF5N MFI: 0.4-0.6


• Exellent punctuer resistance.

• Exellent machinability on conver-

sion lines.

Main Applications

• T-bags and other bags, Food Packag-

ing for frozen products, Agricultural

film, Heat seal film, Food Packaging

Additives

•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• Antiblocking Agent

HP-LL18XF5N


Test MethodTypical Value UnitResin PropertiesD12380.5 (g/10 min)Melt Index (190°C/ 2.16Kg)D15050.918 g/cm³Density

Film Properties @ D 1709125 g Dart ImpactD1525127 °CVicat Softening PointD638 11/10(MD/TD)MpaTensile Strenght at YieldD63840/35(MD/TD)MpaTensile Strenght at BreakD638600/750(MD/TD)% Ultimate Elongation

D1922240/400(MD/TD)gElmendorf TearD100330 %HazeD245725 Gloss 45°

@ on 25 micron film obtained on Collin 25, B.u.R 2.5: 1, Temp. profile 155 190°C: melt 200°C

HP-LLDPE made via Spherilene Gas-Phase Technology

47











ommended.



Product data sheet


Jamlene: HD5000S

Typical Applications

• Fishing net, Rope, Agricultural net, Tar-

paulin, Woven sack.

HDPE for Monofilament

HD-5000S

Resin Properties Unit Value Test MethodMelt Index g/10 min 0.8 D1238Density g/cm³ 0.954 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 125 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 1100 D790Tensile Strenght at Yield Mpa 24 D790Tensile Strenght at Break Mpa 39 D638H.D.T °C 75 D648Notched Izod Impact @ 23 °C J/m 400 D256/A

- On compression molded according to ASTM D1928C Processing Conditions Recommended barrel tempratures range is between 160 °C and 190 °C

HD-5000S is a HDPE grade specially designed for monofilament applications, which combines good processability with high tenacity. This grade has good balance of mechanical strength and high production rates. HD-5000S is also well suited for multiply applications, like ropes and stretched filaments.

Product data sheet


60505 is a HDPE injection molding grade which combines high stiffness with good physical properties.This resin is well suited for crates and toys applications.

Density: 0.956-0.960HDPE: 60505/60505UV MFI: 4.5-6.5


• High stiffness with good physical properties.

Main Applications

• injection molding grade

• Crates

• toys applications

Additives• 60505:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• 60505UV:• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer•Thermal Antioxidant

(Process Stabilizer)

6050560505UV


HDPE made via Spherilene Gas-Phase Technology


Physical properties @D7901460(MPa)Flexural modulus

D256/A30(J/m)Notched Izod impact at 23°CD1525125(°C)Vicat softening point

@ on compression moulded specimen obtained according to ASTM D 1928°CFabrication conditions for injection mouldingRecommended barrel temperatures range between 190 and 280°C

Product data sheet


60507 is a HDPE homopolymer which is manufactured in gas phase process for injection molding grade which combines good flowability with balanced physical properties. This resin is well suited for general purpose application requiring high stiffness.

Density: 0.956-0.960HDPE: HD-60507/HD-60507UV MFI: 6.5-8.5


• Good flowability with balanced

phisycal properties.

Main Applications

• Crates

Injection molding grade

Additives

• HD-60507:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• HD-60507UV:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer

HD-60507HD-60507UV



Test MethodTypical ValueUnitResin PropertiesD12387.5(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.958g/mlDensity

Test MethodTypical ValueUnit Resin Properties @D1525126.5(°C)Vicat Softening Point

Test MethodTypical ValueUnitMoulded Properties @D7901450(MPa)Flexural Modulus

D256/A24(J/m)Notched Izod Impact @ 23 °C

Product data sheet


60511 is a HDPE injection molding grade which combines excellent flowability with high stiffness.This resin is well suited for housewares and toys applications.

Density: 0.956-0.960HDPE: 60511/60511UV MFI: 9-13


• Excellent flowability with high stiffness.

Main Applications


• Houseware

• toys

Additives60511:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)60511UV:• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer•Thermal Antioxidant (Process Stabilizer)

6051160511UV



ASTM MethodTypical ValueUnitResin PropertiesD123811(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.960g/mlDensity





Product data sheet

HDPE: CC52501


• Caps and closures for beverage bottles of

sparkling water, hot-filled and carbonated

soft drinks.

HDPE for Injection Molding (Caps & Closures)

CC52501

Resin Properties Unit Value Test MethodMelt Index g/10 min 0.9 D1238Density g/cm³ 0.952 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 123 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 800 D790Tensile Strenght at Yield Mpa 25 D790Tensile Strenght at Break Mpa 36 D638H.D.T °C 78 D648Notched Izod Impact @ 23 °C J/m 80 D256/A

CC52501 is a Narrow MWD HDPE specially designed for beverage bottles of sparkling water, hot-filled and carbonated soft drinks. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52501 does not contain slip agent.


53


Storage and HandlingPolyethylene products (in pelletized or powder form) should not be stored in direct sunshine and/or heat radiation. The Storage area

should be dry and preferably don’t exceed 50 °C. JPC would not responsible about quality diminishing such as color change, bad smell

or est. which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.

The technical information sug-gested uses and application pre-sented are belived to be accurated and reliable, however JPC makes no warranties either express or implied concerning the information herein or the use of our materials.

100

1000

10000

1 10 100 1000 10000

Viscosity

(Pa.s)

Shear Rate (1/s)

Shear‐Viscosity @ 190 °C


Product data sheet

HDPE: CC52502


• Caps and closures for mineral water bot-

tles,Caps for sparkling water and carbonat-

ed soft drinks, beverage caps.


CC52502

Resin Properties Unit Value Test MethodMelt Index g/10 min 2 D1238Density g/cm³ 0.952 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 124 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 1000 D790Tensile Strenght at Yield Mpa 25 D790Tensile Strenght at Break Mpa 38 D638H.D.T °C 78 D648Notched Izod Impact @ 23 °C J/m 180 D256/A

CC52502 is a Narrow MWD HDPE specially designed for mineral water bottles and beverage caps. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52502 does not contain slip agent.


55






100

1000

10000

1 10 100 1000 10000

Viscosity

(Pa.s)

Shear Rate (1/s)



Product data sheet

HDPE: CC52501


• Caps and closures for mineral water

bottles, Caps for sparkling water and car-

bonated soft drinks, beverage caps.


CC52502SU

Resin Properties Unit Value Test MethodMelt Index g/10 min 2 D1238Density g/cm³ 0.952 D1505Thermal Properties Unit Value Test MethodVicat Softening Point °C 124 D1525Molded Properties Unit Value Test MethodFlectural Modulus Mpa 1000 D790Tensile Strenght at Yield Mpa 25 D790Tensile Strenght at Break Mpa 38 D638H.D.T °C 78 D648Notched Izod Impact @ 23 °C J/m 180 D256/A

CC52502 is a Narrow MWD HDPE specially designed for mineral water bottles and beverage caps. This grade has excellent organoleptic properties which prevent unpleasant odor and taste from cap or closure to transfer to water. It has good gas permeability characteristics, superior processability and excellent mechanical strength. HDPE CC52502SU does contain slip agent and stabilized against UV light.


57






100

1000

10000

1 10 100 1000 10000

Viscosity

(Pa.s)

Shear Rate (1/s)



Product data sheet

52505 is a HDPE copolymer which is manufactured in gas phase process. This grade is an injection molding grade for applications requiring a good physical property even at low temperatures, like pails, containers and technical moldings.



• Good physical property even at

low temperatures.

Main Applications

• Containers.

HD-52505/UV


Additives

HD-52505:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)HD-52505 UV:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer


Test MethodTypical ValueUnitResin PropertiesD12385(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.952g/mlDensity

Test MethodTypical ValueUnit Thermal Properties @D1525124(°C)Vicat Softening Point

Test MethodTypical ValueUnitMoulded Properties @D7901200(MPa)Flexural ModulusD63827(MPa)Tensile strenght at yieldD63813(MPa)Tensile strenght at breakD64867(°C)H.D.T

D256/A29(J/m)Notched Izod Impact @ 23 °C

59



@ On compression moulded according to ASTM D1928CProcessing Conditions:Recommended barrel tempratures range between 190 °C and 280 °C.









ommended.




Product data sheet

52511 is a HDPE copolymer injection molding grade for applications requiring a good balance between physical properties and flowability, like housewares and toys.



• Good balance between physical properties and flowability,

Main Applications


• Houseware

5251152511UV


Additives

52511:•Thermal Antioxidant (Process Stabilizer)• Catalyst neutralizer (acid scavenger, lubricant)52511 UV:•Thermal Antioxidant (Process Stabilizer)• Antiblocking Agent• Catalyst neutralizer (acid scavenger, lubricant)• UV Stabilizer






61


Shear-Viscosity @ T190 °C

@ On compression moulded according to ASTM D 1928 C

Processing Conditions:Melt Temperature (°C): 190 -280









ommended.




Product data sheet

52518 is a HDPE copolymer for Injection Moulding for applications requiring a good balance between easy of processability and flowability and mechanical properties.

Density: 0.950-0.954HDPE: HD-52518 MFI: 16-20


• Good balance between easy of

processability and flowability

Main Applications

• Housewares

• High fluidity

• Injection moulding grade

Additives

•Thermal Antioxidant (Process

Stabilizer)

• Catalyst neutralizer (acid

scavenger, lubricant)

HD-52518


Test MethodTypical ValueUnitResin PropertiesD123818(g/10 min)Melt Index (190°C/ 2.16Kg)D15050.952g/mlDensity

Test MethodTypical ValueUnit Thermal Properties @D1525121(°C)Vicat Softening Point

Test MethodTypical ValueUnitMoulded Properties @D7901200(MPa)Flexural Modulus

D256/A19(J/m)Notched Izod Impact @ 23 °C@ on compression moulded specimen, according to ASTM D 1928°C


63



@ On compression moulded according to ASTM D1928CProcessing Conditions:Recommended barrel tempratures range between 190 °C and 280 °C.









ommended.




Product data sheet

32604 is a LLDPE for rotomolding which manufactured by gas phase process. This grade is suitable for all applications which need a good balance among moldability and mechanical properties together with an exceptional stress cracking resistance.

Density: 0.932LLDPE: LL-32604/UV MFI: 4

Features

• Exellent ESCR.

Applications

• High ESCR rotomolded items

Chemical containers.

Additives

• LL-32604:Thermal Antioxidant• LL-32604UV:Thermal AntioxidantUV Stabilizer

LLDPE made via Spherilene Process

LL-32604/UV


Test MethodTypical ValueUnitResin Properties

D12384g/10 minMelt Index

D15050.932g/cm³Density

Test MethodTypical ValueUnitPhysical Properties

D7901350MpaFlectural Modulus

D256/ANBJ/mNotched Izod Impact @ 23 °C

D1693>1000hE.S.C.R

65



- On compression molded according to ASTM D1928CProcessing ConditionsRecommended barrel tempratures range between 190 °C and 280 °C.


Handellling and Health SafetysMolten polymers could be injured skin or eye so safety glass-







ommended.

Storage Polyethylene products (in pelletised or powder form) should not be stored in direct sunshine and/or heat radiation. Ul-traviolet cause a change in the material properties.The Stor-age area should be dry and preferably don't exceed 50 °C. Under cool, dry, dark conditions Jam Polymers polyolefin resins are expected to maintain the original material and processing properties for at least 18 month. . JPC would not ressponsible about quality diminishing such as color change, bad smell or ets which caused by bad storage conditions. It is better to process PE resin within 6 months after delivery.

packagingJam Polymers Polyolefin resins are supplied in pllet form packed in 25kg bags. Alternative packaging modes are aval-able for selected grades.


Product data sheet

MD-38504 is a UV stabilized linear medium density polyethylenee grade with a narrow molecular weight distribution. It is suitable for rotational molding and some injection molding application such as technical parts and closures. Characteristics include: good impact strenght, excellent external and internal surface finish, and is UV stabilized.

Density: 0.936-0.940MDPE: 38504 UV MFI: 3-5


• Good impact strenght

• High ESCR

Main Applications

• Rotomolding

Additives

•Thermal Antioxidant (Pro-

cess Stabilizer)

• Catalyst neutralizer (acid

scavenger, lubricant)

• UV Stabilizer

38504 UV



Physical properties @D790650(MPa)Flexural ModulusD63815(MPa)Tensile strenght at yieldD638800(%)Tensile strenght at breakD25625KJ/m2Charpy Unnotched impact Strength

D1525115(°C)Vicat Softening TemperatureD224060Shore DDurometer Hardness

@ on compression moulded specimen obtained according to ASTM D 1928°C

MDPE made via Spherilene Gas-Phase Technology

67






100

1000

10000

1 10 100 1000 10000

Viscosity

(Pa.s)

Shear Rate (1/s)


Documents

TECHNICAL CATALOGUE - پتروشیمی جمEX5) ... Technical Cataloue 6 About JPC ... COMPONENT Unit SPECIFICATION Propylene % vol min 99.8 Propane …