TouchScreen Controller Installation Guide - GVision ?· TouchScreen Controller Installation Guide VERSION…

Embed Size (px)

Text of TouchScreen Controller Installation Guide - GVision ?· TouchScreen Controller Installation Guide...

  • 1

    TouchScreen Controller

    Installation Guide

    VERSION : 2.5

    DATE : 2005.12.09

  • 2

    Table of Content

    Chapter 1. TOUCH SCREEN CONTROLLER.. 3About this Document 3Touch Screen Controller Components.. 3Hardware System Requirements 3

    Chapter 2.CONTROLLER FEATURES... 4Serial Controller Features 4PS/2 Controller Features. 5USB Controller Features. 6

    Chapter 3. TOUCH SCREEN CONTROLLER HARDWARE INSTALLATION... 75 Wires Resistive USB Touch Screen Controller Hardware Installation. 75 Wires Resistive Serial Touch Screen Controller Hardware Installation. 95 Wires Resistive PS/2 Touch Screen Controller Hardware Installation.. 114 Wires Resistive Serial Touch Screen Controller Hardware Installation. 134 Wires Resistive PS/2 Touch Screen Controller Hardware Installation.. 15

    Chapter 4. SOFTWARE INSTALLATION 17Chapter 5. DRIVER INSTALLATION. 19Windows XP.. 19Windows XP Embedded.. 19Windows 2000... 20Windows Server 2003.. 20Windows NT 4.0.... 21Windows ME.. 21Windows 98... 22Windows 95... 22Windows CE.. 22Windows 3.1.. 23MS-DOS. 23Linux... 24Chapter 6. UNINSTALL TOUCH SCREEN DRIVER.. 31Chapter 7. TOUCH SCREEN DRIVER FUNCTION 31

  • 3

    Chapter 1. TOUCH SCREEN CONTROLLER About this Document The information in this document is subject to change without notice. Touch Screen Controller Components Enhanced anti-noise SMD multi-layered controller board with 2 attached cables Serial controller with a keyboard power tap cable CD-ROM Drive Diskette Hardware System Requirements Computer: IBM Pentium Compatible or above Hard Disk Drive: 5MB of free memory Drive: CD-ROM drive LCD or Monitor: SVGA color Video card: VESA Super VGA BIOS Ext. version 1.2 or newer SVGA Keyboard port: Output 4~6VDC (max. use

  • 4

    Chapter 2. CONTROLLER FEATURES Serial Controller Features (a) Hardware Specifications

    Power Requirements +5VDC ( Maximum 150mA, typical current depend on specified panel, 50mV peak to peak maximum ripple )

    Operating Temperature 0 to 60

    Storage Tempeture -40 to 80

    Relative Humidity 95% at 60

    Protocol 38400 BPS baudrate, 1 Start bit, 8 Data bits, None parity, 1 Stop Bit.

    Resolution Sample 4096X4096 (12Bits), Report 1024X1024(10Bits)

    Report Rate Minimum 65 PPS (Point per Second)

    Response Time Maximum 20 ms

    Pin Out Definition 4 wire : YU, YD, XR, XL 5 wire : RT, RL, SG, LT, LL

    Panel Resistance 4 wire : 150 to 1500 Ohm ( pin to pin on the same layer ) 5 wire : 30 to 500 Ohm ( pin to pin on drive layer )

    (b) Software Specifications Serial Port Support

    COM1 to COM9 for DOS , Windows 95/98/ME/2000/XP/NT4/2003 COM1 to COM4 for Windows 3.1

    Virtual Button

    1. Stream Mode 2. Touch Down Mode 3. Lift Off Mode 4. Drag Drop Mode Support right button function

    Feedback Sound

    1. Silence ( No Sound ) 2. Touch Down Only 3. Lift Off Only 4. Both Touch Down and Lift Off

    Mouse Speed

    1. Bypass 2. Acceleration ( Slow, Medium, Fast, Off ) 3. Horizontal Speed ( 5% to 100% ) 4. Vertical Speed ( 5% to 100% )

    Power Save

    1. Disable 2. Enable ( 10 sec. to 300 sec. )

    Calibration Fast 4 point position

    OS Support

    1. MS-DOS 2. Windows 3.1/95/98/ME/NT4/2000/XP/2003 3. Redhat/Mandrake Linux (XOrg version 6.4.x / XFree86 version 4.1 or later ) 4. Windows CE 3.1/.NET

  • 5

    PS/2 Controller Features (a) Hardware Specifications

    Power Requirements +5VDC ( Maximum 30mA, typical 15mA, 50mV peak to peak maximum ripple )

    Operating Temperature 0 to 60

    Storage Tempeture -40 to 80

    Relative Humidity 95% at 60

    Protocol Standard 2 button PS/2 Mouse.

    Resolution Sample 4096X4096 (12Bits), Report 1024X1024(10Bits)

    Report Rate Minimum 60 PPS (Point per Second)

    Response Time Maximum 20 ms

    Pin Out Definition 4 wire : YU, YD, XR, XL 5 wire : RT, RL, SG, LT, LL

    Panel Resistance 4 wire : 150 to 1500 Ohm ( pin to pin on the same layer ) 5 wire : 30 to 500 Ohm ( pin to pin on drive layer )

    Extend PS/2 Mouse Port Support standard 2 button PS/2 Mouse

    (b) Software Specifications

    PS/2 Port Support Auto detect function

    Virtual Button

    1. Stream Mode 2. Touch Down Mode 3. Lift Off Mode 4. Drag Drop Mode Support right button function

    Feedback Sound

    1. Silence ( No Sound ) 2. Touch Down Only 3. Lift Off Only 4. Both Touch Down and Lift Off

    Mouse Speed

    1. Bypass 2. Acceleration ( Slow, Medium, Fast, Off ) 3. Horizontal Speed ( 5% to 100% ) 4. Vertical Speed ( 5% to 100% )

    Calibration Fast 4 point position

    OS Support

    1. MS-DOS 2. Windows 3.1/95/98/ME/NT4/2000/XP/2003 3. Redhat/Mandrake Linux (XOrg version 6.4.x / XFree86 version 4.1 or later ) 4. Windows CE 3.1/.NET

  • 6

    USB Controller Features (a) Hardware Specifications Power Requirements +5VDC ( Maximum 100mA )

    Operating Temperature 0 to 60

    Storage Tempeture -40 to 80

    Relative Humidity 95% at 60

    Protocol Standard USB Mouse.

    Report Rate Minimum 160 PPS (Point per Second)

    Response Time Maximum 35 ms

    Pin Out Definition 5 wire : RT, RL, SG, LT, LL

    Panel Resistance 5 wire : 30 to 500 Ohm ( pin to pin on drive layer )

    (b) Software Specifications USB Port Support Auto detect function

    Virtual Button

    1. Stream Mode 2. Touch Down Mode 3. Lift Off Mode 4. Drag Drop Mode Support right button function

    Feedback Sound

    1. Silence ( No Sound ) 2. Touch Down Only 3. Lift Off Only 4. Both Touch Down and Lift Off

    Mouse Speed

    1. Bypass 2. Acceleration ( Slow, Medium, Fast, Off ) 3. Horizontal Speed ( 5% to 100% ) 4. Vertical Speed ( 5% to 100% )

    Calibration Fast 4 point position

    OS Support

    1. Windows 2000/XP

  • 7

    Chapter 3. TOUCH SCREEN CONTROLLER HARDWARE INSTALLATION 5 Wires Resistive USB Touch Screen Controller Hardware Installation This chapter discusses how to install your 5 wires resistive serial touch screen controller, follow the directions starting on the next section to install the controller to your computer.

    IMPORTANT: Before connecting the touch screen controller to your computer system,Be sure that the computer system is turned off.

    1. Turning Off Your Computer System

    Before you install the 5 wires resistive USB touch screen controller, turn off your computer system. 2. Connecting the Controller

    The 5 wires resistive USB touch screen controller included a USB cable, which has 5-pin D connector.. Plug the USB cable into a USB port on your computer directly .

    3. Supplying Power to the Controller

    The 5 wires resistive USB touch screen controller included a 5-pin USB cable, which using to provide power to the controller. To connect USB cable: Plug the USB cable into usb port.

    4. Mounting the Touch Panel

    There are several methods for mounting the touch panel (or sensor) depending on your application. The 5 wires

    resistive serial touch screen controller included a 5-pin ( pitch 2.54mm) touch panel cable. The Pin Assignment of

    Touch Panel Cable listed in below, if your touch panels pin out does not match it, you may need jumping cable

    Pin 1 Pin 2 Pin 3 Pin 4 Pin 5

    RT RL SG LT LL

  • 8

    5. Turning On Your Computer System

    Before you turn on your computer system, ensure that all cables are connected properly and that the controller is properly mounted. Be sure to tighten all cable connector screws. To start up your system: Turn on your computer system. Adjust the horizontal and vertical position controls on the monitor to center the image on the screen.

    6. Check the Status LED

    The 5 wires resistive USB touch screen controller has a LED (light emitting diode) on the box that indicates the status of the controller. When you power-up the unit, the LED is on after the controller start-up sequence is completed. Following start-up, the LED goes on and remains on as long as you do not touch the sensor. After the TouchScreen Driver is installed and startup, when you touch the sensor, the LED goes flashing (or blinking ) until you lift off from the sensor.

    7. Installing and Using TouchScreen Software You have successfully installed the 5 wires USB touch screen controller and connected the touchscreen to your computer. You are now ready to complete the following tasks: install the appropriate TouchScreen Driver software for the operating system you are using. Use the TouchScreen Control Panel software to calibrate the touchscreen. Insert the TouchScreen Drivers CD-ROM in your computers CD-ROM drive and follow the directions starting on the next page to install the driver software.

  • 9

    5 Wires Resistive Serial Touch