View
229
Download
0
Category
Preview:
Citation preview
8/18/2019 Matsui 1409r Tv Sm
1/29
This Manual is available in Electronic format.
SERVICE MANUAL
MATSUI 1409R/TTV
Version 1.0
Mastercare, Maylands Avenue, Hemel Hempstead, Hertfordshire, HP2 7TG, Telephone 01442 888104
Manual Number: 668502
8/18/2019 Matsui 1409r Tv Sm
2/29
MATSUI 1409R/TTV
PRODUCED BY
MASTERCARE TECHNICAL CENTRE
SERVICE MANUAL
Specifications are subject to change without notice.
COPYRIGHT © 2000 MASTERCARE LIMITED
8/18/2019 Matsui 1409r Tv Sm
3/29
SERVICING NOTICES ON CHECKING
6. AVOID AN X-RAY1. KEEP THE NOTICES
As for the places which need special attentions,they are indicated with the labels or seals on thecabinet, chassis and parts. Make sure to keep theindications and notices in the operation manual.
3. USE THE DESIGNATED PARTS
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
Safety is secured against an X-ray by consider-ing about the cathode-ray tube and the highvoltage peripheral circuit, etc.Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts andmake sure not modify the circuit.Repairing except indicates causes rising of highvoltage, and it emits an X-ray from the cathode-ray tube.
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER.2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
HOW TO ORDER PARTS
Inferior silicon grease can damage IC's and transistors.When replacing an IC's or transistors, use only specified silicon grease (YG6260M).Remove all old silicon before applying new silicon.
IMPORTANT
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid anelectric shock while the electric current isflowing.
The parts in this equipment have the specificcharacters of incombustibility and withstandvoltage for safety. Therefore, the part which isreplaced should be used the part which hasthe same character.Especially as to the important parts for safetywhich is indicated in the circuit diagram or the
table of parts as a mark, the designatedparts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulationmaterial such as a tube or tape for safety, orwhich are assembled in the condition thatthese do not contact with the printed board.The inside wiring is designed not to get closerto the pyrogenic parts and high voltage parts.Therefore, put these parts in the originalpositions.
In the condition that an explosion-proof cathode-ray tube is set in this equipment, safety issecured against implosion. However, whenremoving it or serving from backward, it isdangerous to give a shock. Take enough care todeal with it.
PERFORM A SAFETY CHECK AFTER
SERVICING
7.
Confirm that the screws, parts and wiring whichwere removed in order to service are put in theoriginal positions, or whether there are theportions which are deteriorated around theserviced places serviced or not. Check theinsulation between the antenna terminal or
external metal and the AC cord plug blades.And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
1.2.
3.
4.
Unplug the plug from the AC outlet.Remove the antenna terminal on TV and turnon the TV.Insulation resistance between the cord plugterminals and the eternal exposure metal[Note 2] should be more than 1M ohm byusing the 500V insulation resistance meter[Note1] .If the insulation resistance is less than 1Mohm, the inspection repair should berequired.
[Note 1]
If you have not the 500V insulationresistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminalEarphone jack
A1-1
8/18/2019 Matsui 1409r Tv Sm
4/29
CONTENTS
A2-1
SERVICING NOTICES ON CHECKING ...................................................................................................HOW TO ORDER PARTS ........................................................................................................................IMPORTANT .............................................................................................................................................CONTENTS ..............................................................................................................................................GENERAL SPECIFICATIONS .................................................................................................................DISASSEMBLY INSTRUCTIONS ............................................................................................................SERVICE MODE LIST ..............................................................................................................................CONFIRMATION OF USING HOURS ......................................................................................................NOTE FOR THE REPLACING OF MEMORY IC .....................................................................................ELECTRICAL ADJUSTMENTS ...............................................................................................................MAJOR COMPONENTS LOCATION GUIDE ..........................................................................................BLOCK DIAGRAM ...................................................................................................................................PRINTED CIRCUIT BOARDS
MAIN/CRT/T'TEXT...............................................................................................................................SCHEMATIC DIAGRAMS
MICON/TUNER....................................................................................................................................IF/CHROMA .........................................................................................................................................POWER ...............................................................................................................................................DEFLECTION/CRT..............................................................................................................................21PIN/SOUND .....................................................................................................................................VIDEO/RGB SW ..................................................................................................................................T'TEXT .................................................................................................................................................
WAVEFORMS ..........................................................................................................................................MECHANICAL EXPLODED VIEW ...........................................................................................................PARTS LIST .............................................................................................................................................
A1-1A1-1A1-1A2-1A3-1~A3-4B-1C-1C-1C-1D1-1~D2-1D3-1E-1, E-2
F-1~F-4
G-1, G-2G-3, G-4G-5, G-6G-7, G-8G-9, G-10G-11, G-12G-13, G-14H-1~H-3I-1NOT AVAILABLE
8/18/2019 Matsui 1409r Tv Sm
5/29
GENERAL SPECIFICATIONS
A3-1
G-1.Outline of the Product
14 inch(335.4mmV):Measured diagonally
Color CRT 90 degree deflection
G-2.Broadcasting System
U.K. System I
G-3.Color System NTSC PAL SECAM or Monochrome signal
G-4.NTSC Playback(PAL 60Hz) Yes No
G-5.NTSC 3.58+4.43/PAL60Hz Yes No
G-6.Antenna Input Impedance
VHF/UHF 75 ohm unbalanced
G-7.Tuner and Receiving Contactless Electric tuner 1Tuner System
2Tuner System
channel Tuner Oscar(W/O HYPER) Oscar(W/ HYPER)
France CATV) Others
cannel coverage 21~ 69
Tuning System
Frequency syn. Voltage syn. Others
G-8.Preset Channel 80 channels
G-9.Intermediate FrequencyPicture(fP) 39.5 MHz MHz MHzSound (fS) 33.5 MHz MHz MHzfP-fS 6.0 MHz MHz MHz
G-10.Stereo/Dual TV Sound
Yes( NICAM GERMAN USA JAPAN) No
G-11.Tuner Sound Muting Yes No
G-12.Power Source 230~240 V AC 50Hz AC 60Hz
G-13.Power Consumption: 44 W at AC 230 V 50 Hz
W at DC V
Stand by: 10 W at AC 230 V 50 Hz
Per Year: - kWh / Year
G-14.Dimensions(Approx.)
362.0 mm(W) 360.0 mm(D) 320.5 mm(H)
G-15.Weight(Approx.) Net: 9.5 kg ( - lbs)
Gross: 11.5 kg ( - lbs)
G-16.Cabinet Material
Cabinet Front: PS 94HB DECABROMABS 94V2 NON-DECA
94V0
Back Panel: PS 94HB DECABROMABS 94V2 NON-DECA
94V0
Jack Plate: PS 94HB DECABROMABS 94V2 NON-DECA
94V0
8/18/2019 Matsui 1409r Tv Sm
6/29
GENERAL SPECIFICATIONS
A3-2
G-17.Protector: Power Fuse
G-18.RegulationSafety
UL CSA SAA SI CE SEVBS NF NEMKO FEMKO DEMKO IEC65
SEMKO NZ HOMOLO SABS CNS SISIRNOM AS3159 DENTORI UNE GOST NONE
RadiationFCC DOC FTZ PTT CE SEVSABA SI NF NZ HOMOLO UNECNS CISPR13 DENTORI AS/NZS NONE
X-RadiationPTB DHHS HWC DENTORI NONE
G-19.Temperature
Operation 5 º C~ 40 ºC
Storage -20 ºC~ 60 ºC
G-20.Operating Humidity Less than 80 %RH
G-21.Clock and TimerSleep Timer Yes Max 120 Min.( 10 Min. Step) No
On/Off Timer Yes Programs No
Wake Up Timer Yes Programs No
G-22.Timer back up Time
More than - Minutes (at Power Off Mode)
G-23.Terminals
VHF/UHF Antenna Din Type F-Type France Type
Video Input(Front) (RCA ø8.3)
Video Input(Rear)(x ) (RCA ø8.3)
Video Output(Rear) (RCA ø8.3)
Audio Input(Front) (RCA ø8.3)Audio Input(Rear)(x ) (RCA ø8.3)
Audio Output(Rear) (RCA ø8.3)
21 Pin (x 1 ) DC Jack(Center +) Ear Phone Jack(ø3.5)
Head Phone Jack(ø3.5) AC Outlet Ext Speaker
Diversity S Input(Front) S Input(Rear)
G-24.IndicatorPower Stand By On Timer
( ) ( Red ) ( )
G-25.Display
On Screen Display
Menu
Clock Set( 12H 24H) System SelectOn/Off Timer Hotel Lock Area Code
CH Tuning Sound 1/2 NICAM Auto Off
Picture Guide CH Set Audio
Language CATV
Pin Code Registration
Control Level
Sound Brightness Contrast
Color Tint(NTSC Only) Sharpness
Tuning Bass Treble
Balance Back Light
Stereo,Audio Output,Bilingual Picture Menu AFT
Stereo,Audio Output,SAP Mid Night Theater Sound MuteStereo,Audio Output GAME Sleep Time
CH Clock Pin Code Hotel Lock Skip
8/18/2019 Matsui 1409r Tv Sm
7/29
GENERAL SPECIFICATIONS
A3-3
G-26.OSD Language
Eng Ger Fre Spa Ita Por Jpn
OSD Language Setting
Eng Ger Fre Spa Ita Por Jpn
Not ApplicableG-27.Speaker : Pos it ion Front Side Bottom
Size 3 inches
Imp 8 ohm x 1 pcs
Power Max 1.5 W
10% 1.0 W (Typical)
G-28.EXT Speaker
Yes W Imp ohm
G-29.Carton
Master Carton: Need No Need
Content: ---- Set
Material: ---- / ---- Corrugated Carton
Dimensions: ---- mm(W) ---- mm(D) ---- mm(H)
Description of Origin Yes No
Gift Box
Material Double/Brown Corrugated Carton ( with Photo Label)
Double/White Corrugated Carton ( with Photo Label)
Double Full Color Carton W/Photo
Dimensions: 440 mm(W) 408 mm(D) 380 mm(H)
Design: As Per BUYER 's
Description of Origin: Yes No
Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height 25cm 31cm 46cm 62cm 80cm
Container Stuffing: 866 Sets / 40' container
G-30.Accessories
Owner's Manual ( W/Guarantee Card) [ English ]
AC Plug Adapter Channel Film
Battery (UM- 4 x 2 ) Remote Control Unit
Safety Tip Toll Free Insert Sheet
Guarantee Card Audio-Video Cord (RCA)
Registration Card Warning Sheet
Quick Set-Up Sheet Schematic Diagram
Information Sheet U/V Mixer
75 ohm Coaxial Cable ( Single Shield Double Shield)
300 ohm to 75 ohm VHF Antenna Adaptor
21pin Cable Car Cord
Rod Antenna
One Pole Two Pole ( F-Type Din Type France Type)
Loop Antenna ( F-Type Din Type France Type)
G-31.Other Features
Auto Degauss Auto Search Full OSD
Auto Shut Off CH Allocation Premiere
Canal+ SAP Comb Filter
CATV Channel Lock Auto CH Memory
Anti-Theft Just Clock Function Hotel Lock
Rental Game Position Fastext
Unitext TopText Closed Caption
Picture Menu Mid Night Theater Memory(Last CH,Last Volume)
8/18/2019 Matsui 1409r Tv Sm
8/29
GENERAL SPECIFICATIONS
A3-4
G-32.Switch
Front
Power(Tact) Channel Up Volume Up
System Select Channel Down Volume Down
Main Power SW
Rear
AC/DC TV/CATV Selector
Degauss Main Power SW
G-33.Magnetic Field
BV : +0.45G BV : +0.35G BV : +0.25G
BH : 0.18G BH : 0.30G BH : 0.30G
BV : -0.15G BV : -0.25G BV : -0.50G
BH : 0.15G BH : 0.15G BH : 0.30G
G-34.Remote Control Unit: RC-DG
Glow in Dark Remcon Yes No
Power Source: D.C 3 V Battery UM - 4 x 2
Total 25 Key Power Quick View/Sub Page TV/AV
Stand By Status/Hold Bar Select
0/AV Quick View PAL/SECAM
1 Time Set Volume Up
2 Mute Volume Down
3 CH Skip CH Call
4 CH1/CH2 CH Down
5 Display Cancel CH Up
6 Text/Mix/TV CH Down/Page Down
7 Cancel/Display Cancel CH Up/Page Up
8 Cancel Page +/-
9 Store Program10 Skip/Reveal F/T/B
11 Sleep Hold
12 Skip List
Volume Up/ + Preset Rotate
Volume Down/ - Normal/ F/T/B Browse
0/10 Auto Memory Std/Auto
Tone 1/2/Reset Auto Memory
Info Call Band Select
Fine Tuning + Reset Search
TV/Caption/Text Menu Clock/Program
Normal/Expand Enter Clock/Set
Red Add Ch Set
Cyan/Fine Tuning + Delete Set +Normal Yellow/Fine Tuning- Set -
Color System Fine Tuning- Green
Wide Selecy Sub Page Nicam/Mono
Auto Wide On/Off Reset Tone 1/2(A/B)
Picture Position Navi FM Transmitter
Direct Change/Auto Search Back Light
Picture Menu Mid Night Theater
8/18/2019 Matsui 1409r Tv Sm
9/29
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work.
After turning the power off there might still be a potential
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap'spotential voltage.
Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.
*
*
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
Flip up the sides of the Rubber Cap in the direction of thearrow and remove one side of the support.(Refer to Fig. 1-2.)
2.
DISASSEMBLY INSTRUCTIONS
GND on the CRT
Screwdriver
Alligator Clip
SupportCRT
GND on the CRT
Rubber Cap
CRTSupport
Fig. 1-1
Fig. 1-2
3. After one side is removed, pull in the opposite direction toremove the other.
NOTE
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a smallamount of alcohol. (Refer to Fig. 1-3.)
B-1
Location of Anode Cap
Fig. 1-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot wherethe cap was located.
2.
3.
Arrange the wire of the Anode Cap and make sure thewire is not twisted.
Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Fig. 1-4
4. Insert one end of the Anode Support into the anode button,then the other as shown in Fig. 1-5.
5.6.
Confirm that the Support is securely connected.Put on the Rubber Cap without moving any parts.
CRTSupport
Fig. 1-5
8/18/2019 Matsui 1409r Tv Sm
10/29
INIT 00 83
0010CRT ON
ADDRESS DATA
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.To enter the Service Mode, press both set key and remote control key for more than 1 second.
Set Key Remocon Key Operations
C-1
VOL. (-) MIN 1
VOL. (-) MIN 6
Initialization of the factory.NOTE: Do not use this for the normal servicing.
POWER ON total hours is displayed on the screen.Refer to the "CONFIRMATION OF USING HOURS".
Can be checked of the INITIAL DATA of MEMORY IC.Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".
VOL. (-) MIN 7 Releasing of PROTECTION PASSWORD.
VOL. (-) MIN 8Writing of EEPROM initial data.NOTE: Do not use this for the normal servicing.
VOL. (-) MINDisplay of the Adjustment MENU on the screen.Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
9
CONFIRMATION OF USING HOURS
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
1.2.
3.
Set the VOLUME to minimum.Press both VOL. DOWN button on the set and Channelbutton (6) on the remote control for more than 1 second.After the confirmation of using hours, turn off the power.
FIG. 1
Initial setting content of MEMORY IC.
POWER ON total hours. = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value)
+ (16 x tens digit value) + (ones digit value)
NOTE FOR THE REPLACING OF MEMORY IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken toensure correct data settings while making reference to TABLE 1.
NOTE: No need the setting for the data except the Table 1.
ADDRESS DATA
1 00
2 00
3 004 00
5 10
6 28
ADDRESS DATA
7 C0
8 34
9 51A 00
B 00
C 80
ADDRESS DATA
D 00
E 03
F 0010 35
11 00
12 00
ADDRESS DATA
13 00
14 00
15 0016 00
21 4C
2E 06
1.2.3.4.
5.6.
7.8.9.The unit will now have the correct DATA for the new MEMORY IC.
Enter DATA SET mode by setting VOLUME to minimum.Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.ADDRESS and DATA should appear as FIG 1.ADDRESS is now selected and should "blink". Using the VOL. UP or DOWN keys on the remote, step through theADDRESS until required ADDRESS to be changed is reached.Press ENTER to select DATA. When DATA is selected, it will "blink".Again, step through the DATA using VOL. UP or DOWN keys until required DATA value has been selected.
Pressing ENTER will take you back to ADDRESS for further selection if necessary.Repeat steps 4 to 7 until all data has been checked.When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
Table 1
8/18/2019 Matsui 1409r Tv Sm
11/29
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICALADJUSTMENTS
•
•
•
•
Use an isolation transformer when performing anyservice on this chassis.Before removing the anode cap, discharge electricitybecause it contains high voltage.When removing a PCB or related component, afterunfastening or changing a wire, be sure to put the wireback in its original position.Inferior silicon grease can damage IC's and transistors.When replacing IC's and transistors, use only specifiedsilicon grease (YG6260M).Remove all old silicon before applying new silicon.
D1-1
Read and perform these adjustments when repairing thecircuits or replacing electrical parts or PCB assemblies.
CAUTION
Prepare the following measurement tools for electricaladjustments.
1. Synchro Scope2. Digital Voltmeter
On-Screen Display Adjustment
1. In the condition of NO indication on the screen.Press the VOL. DOWN button on the set and theChannel button (9) on the remote control for more than1 second to appear the adjustment mode on the screenas shown in Fig. 1-1.
Fig. 1-1
TV
00 OSD 15
2.
3.
Use the PROG/PAGE button or Channel button (0-9)on the remote control to select the options shown inFig. 1-2.Press the MENU button on the remote control to endthe adjustments.
FUNCTIONOSDCUT OFFRF.AGCVCO CENTH.POSI(50)V.POSI(50)V.SIZE(50)V.LINEAR(50)V.S CORR(50)G.DRVB.DRV
R.BIASG.BIASB.BIAS
NO.0001020304050607080910
111213
FUNCTIONBRICONTUNI COLTINTSHARPRGB CONTSUB COLB.B TINTR-Y BB-Y BLEVEL
STEREOT.MONOT.STE
NO.1415161718192021222324
252627
2. BASIC ADJUSTMENTS
Fig. 1-2
2-1: CONSTANT VOLTAGE
1.2.
3.4.5.
Place the set with Aging Test for more than 15 minutes.Using the remote control, set the brightness and
contrast to normal position.Connect the digital voltmeter to TP401.Set condition is AV MODE without signal.Adjust the VR501 until the DC voltage is 131.5 ± 0.5V.
2-2: VCO CENT
1.
2.
Activate the adjustment mode display of Fig. 1-1 andpress the channel button (03) on the remote control toselect "VCO CENT".Adjust the L201 until the "OK" appears on the screen.
1.
2.3.4.
5.
Place the set with Aging Test for more than 15 minutes.
Receive an 80dB monoscope pattern.Connect the digital voltmeter to pin 5 of CP101.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (02) on the remote control toselect "RF.AGC".Press the VOL. UP/DOWN button on the remote controluntil the digital voltmeter is 2.3 ± 0.05V.
2-3: AGC VOLTAGE
1.2.
3.
Place the set with Aging Test for more than 15 minutes.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (01) on the remote control toselect "CUT OFF".
Adjust the Screen Volume until a dim raster is obtained.
2-4: CUT OFF
2-5: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
1.2.
3.
4.
5.
6.
7.
8.
Place the set with Aging Test for more than 10 minutes.Receive the white 100% signal from the PatternGenerator.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (11) on the remote control toselect "R.BIAS".Using the VOL. UP/DOWN button on the remote control,
adjust the R.BIAS.Press the PROG/PAGE button on the remote control toselect the "G.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".Using the VOL. UP/DOWN button on the remote control,adjust the G.DRIVE, B.DRIVE, G.BIAS or B.BIAS.Perform the above adjustments 6 and 7 until the whitecolor is looked like a white.
2-6: FOCUS
1.2.3.
Receive an 80dB monoscope pattern.Turn the Focus Volume fully counterclockwise once.Adjust the Focus Volume until picture is distinct.
8/18/2019 Matsui 1409r Tv Sm
12/29
ELECTRICAL ADJUSTMENTS
D1-2
1.2.
3.
4.
5.6.
Receive an 80dB monoscope pattern. (RF Input)Using the remote control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (14) on the remote control toselect "BRI".Press the VOL. UP/DOWN button on the remotecontrol until the white 25% is starting to be visibleReceive the monoscope pattern. (Audio Video Input)Press the AV button on the remote control to set to theAV mode. Then perform the above adjustments 2~4.
2-7: BRIGHTNESS
2-8: HORIZONTAL POSITION
1.2.
3.
4.
5.
6.
Receive the monoscope pattern.Using the remote control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 and
press the channel button (04) on the remote control toselect "H.POSI(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onright and left becomes minimum..Receive the monoscope pattern of NTSC. (Audio VideoInput)Press the AV button on the remote control to set to theAV mode. Then perform the above adjustments 2~4.
2-9: VERTICAL POSITION
1.2.
3.
4.
5.
6.
Receive the monoscope pattern.Using the remote control, set the brightness and
contrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (05) on the remote control toselect "V.POSI(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onupside and downside becomes minimum..Receive the monoscope pattern of NTSC. (Audio VideoInput)Press the AV button on the remote control to set to theAV mode. Then perform the above adjustments 2~4.
2-10: VERTICAL SIZE
NOTE: Adjust after performing VERTICAL POSITIONadjustment.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Receive the monoscope pattern.
Using the remote control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (06) on the remote control toselect "V. SIZE(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onupside and downside becomes 8 ± 2%.Receive the monoscope pattern of NTSC. (Audio VideoInput)Press the AV button on the remote control to set to theAV mode.Using the remote control, set the brightness andcontrast to normal position.
Activate the adjustment mode display of Fig. 1-1 andpress the channel button (06) on the remote control toselect "V. SIZE(50)".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onupside and downside becomes 10 ± 2%.
2-11: OSD HORIZONTAL
1.2.
Activate the adjustment mode display of Fig. 1-1.Press the VOL. UP/DOWN button on the remotecontrol until the difference of A and B becomesminimum. (Refer to Fig. 2-1)
BA
TV
00 OSD 15
Fig. 2-1
8/18/2019 Matsui 1409r Tv Sm
13/29
ELECTRICAL ADJUSTMENTS
3.
1.
2.
3.
1.
2.
3.
4.
5.
6.
7.
8.
3-2: PURITY
NOTEAdjust after performing adjustments in section 3-1.
1.
2.
3.
4.5.
Receive the green raster pattern from color bargenerator.Adjust the pair of purity magnets to center thecolor on the screen.Adjust the pair of purity magnets so the color at theends are equally wide.Move the deflection yoke backward (to neck side)slowly, and stop it at the position when the wholescreen is green.Confirm red and blue colors.Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw.
DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW
PURITY MAGNETS
6 POLE MAGNETS4 POLE MAGNETS
Fig. 3-1
PURITY AND CONVERGENCEADJUSTMENTS
NOTE
NOTE
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
Tighten the screw for the magnet. Refer to the adjustedCRT for the position. (Refer to Fig. 3-1)If the deflection yoke and magnet are in one body,untighten the screw for the body.Receive the green raster pattern from the color bargenerator.Slide the deflection yoke until it touches the funnel
side of the CRT.Adjust center of screen to green, with red and blue on thesides, using the pair of purity magnets.Switch the color bar generator from the green rasterpattern to the crosshatch pattern.Combine red and blue of the 3 color crosshatch patternon the center of the screen by adjusting the pair of4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.Adjust the crosshatch pattern to change to whiteby repeating steps 6 and 7.
Turn the unit on and let it warm up for at least 30minutes before performing the following adjustments.Place the CRT surface facing east or west to reduce theterrestrial magnetism.Turn ON the unit and demagnetize with a Degauss Coil.
Adjust after performing adjustments in section 3-2.
3-3: STATIC CONVERGENCE
1.
2.
3.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1.
2.
Adjust the differences around the screen by movingthe deflection yoke upward/downward and right/left.(Refer to Fig. 3-2-a)
Insert three wedges between the deflection yoke andCRT funnel to fix the deflection yoke.(Refer to Fig. 3-2-b)
R G B
RGB
Fig. 3-2-a
WEDGE WEDGE
WEDGE
WEDGE POSITION
Fig. 3-2-b
R G B
RGB
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
Receive the crosshatch pattern from the color bargenerator.Combine red and blue of the 3 color crosshatch patternon the center of the screen by adjusting the pair of4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.
D2-1
8/18/2019 Matsui 1409r Tv Sm
14/29
MAJOR COMPONENTS LOCATION GUIDE
D3-1
CP101
FB401
FOCUS VOLUMESCREEN VOLUME
TP401TU001
MAIN
J352
T502
VR501
L201
IC201
8/18/2019 Matsui 1409r Tv Sm
15/29
8/18/2019 Matsui 1409r Tv Sm
16/29
C P 8 0 2 B
L801
J 8 0 1
CP801
CP806
T P 0 2 4 TP022
TP023
C801
SW501
T U 0 0 1
CP501
F501 FFH502
C 4 3 9
D 0 0 1
D 7 0 6
C 0 0 2
C 7 0 2
L 7 0 2
L 7 0 1
C 6 0 4
C 6 0 3
C 6 0 2
W 8 0 9
L 7 5 3
IC351
C 3 5 7
C 5 1 6
C 5 0 6
L101
IC103
X101
D 1 0 4
D 1 0 5
IC199
R 1 2 6
I C 5 0 1
D103
J705
PH001
W088
D 5 0 5
W038
SW104SW102SW107SW106
CP101
R003
R004
R 7 1 0
C 5 0 5
R 1 2 8
W037
W086
R 1 1 4
W 0 7 8 C 1
0 3
C 1 1 1
Q701
R 7 5 6
W 0 8 3
R
1 3 1
C350
CC004
W087
C 0 0 3
C 5 2 1
R107
C 3 5 1
C 3 5 3
FB401
C 4 3
5
C511_1
R 5 0 4
C406
C 4 4 8
C 4 0 3
R518
VR501
C 5 1 2 _1
D506
C 5 0 1
R 5 0 9
D507R 5 0 8
Q502
R 5 0 6
C 5 0 9
D 5 0 9
B 5 0 1
R 4 2 9
D 4 1 0
D405
C420
R403
C 5 2 6
IC506
C5 0 7
D528
D513
B 5 0 4
C517
C 5 1 9
C 5 1 5
R 5 1 6
CP351
D615
C 3 5 6
R 3 5 7
W 0 7 7
B 3 5 1
W 0 5 5 W
0 7 9
R 1 0 1
C 1 0 2
W090
C223
C217
X601
L201
C 2 0 2
L203
C F 2 0 1
CF204
R212
IC201
L202
C 2 0 5
C 2 1 0
C209
W093
C 2 1 9
C631
C 6 2 3
C625C620C615
C605
CF203
CF202
L204
C201
W 0 8 0
C 2 1 3
W 0 9 7
W897
W 0 1 3
C 4 4 0
R446
R427
D 4 0 4
C 4 0 7
R 4 4 5
R 4
2 1
C 4 4 6
T401
TP401
W 8 1 3
C 4 3 0 R410
C 4 2 5
D 4 0 3
C414
C 4 1 0
C 5 1 0
L 6 0 3
CP401
W063
R406
R 5 0 5
D516
C520
C 5 2 2
Q503
C 5 2 7
R 5 2 2
R 0 0 1
R 0 0 2
Q504
I C 5 0 2
C 5 2 4
C 5 2 5
D 5 1 9
D 5 2 1
C 5 2 3
D 5 2 0
C 6 3 5
R 5 1 4
R 4 0 4
W 0 9 9
L 7
0 3
W092
W094
W 8 1 4
C 3 5 2
L602
T502
C 0 0 1
L 0 0 1
W811
C 6 1 9
C 6 1 7
C 6 1 8
R 3 5 5
R 1 0 2
W 0 8 9
W
1 0 4
C216
D510
R 4 1 5
W068
W022
R 5 2 0
W052
D512
L 5 0 1
W 0 0 6
W009
W034
W035
W036
R 1 2 4
Q507
R 4 2 2
W051
W053
W076
Q506
R 1 0 4
D518
W054
W
1 0 3
W1 0 2
R 5 2 3
D 5 1 5
R408
W 8 1 2
W024
W 0 2 1
R 4 1 4
W046
W 0
1 6
W 0 4 3 W
0 4 1
W 0 5 0
W 0 4 7
L206
W 0 7 3
W020
C 6 0 9
Q401_1
R515
C 6 2 2
W091
C621
W039
W 8 2 4
W 0 5 9
W082
HS401
I C 4 0 1
W 0 2 5
CP802A
C 4 0 9
W007
W 0 0 8
R 4 0 7
W 0 2 9
D406
R 4 1 7
R 4 1 8
D407
R 6 2 4
W 0 6 7
W010
W101
C 2 2 1
W 0 6 6
W801
W 8 6 1
C 3 5 9
C 7 0 8 _1
C 7 5 9
C 1 0 1
R 8 0 7
R 8 0 3
R 8 0 5
R802
R804
W106
W105
R 8 0 6
W111
W110
R 5 1 0
R 5 1 1
W 0 0 1
W107
W 0 0 5
D508
W 0 2 3
R 6 0 9
B 2 0 1
R 1 4 1
R602
W1 1 2
W062
C 6 4 0
D614
W 0 7 2
W 0 7 1
W061
W113
W 0 6 0
W064
R146
C 1 0 6
W056
W 0 7 5
W074
W017
W1 1 4
W 0 4 4 W040
W 0 4 5
W 0 4 9
C 6 4 2
C 6 4 1
Q612
C 5 3 1
W033
W027
D 6 1 1
W 0 6 5
W058
W
1 1 5
W 8 0 8
C 5 0 8
D 5 1 4
W014
W015
W 0 1 9
W031
W 0 1 8
W1 1 7
Q803
Q801
Q802
Q402
C110
W 0 1 2
W 0
7 0
D 5 1 1
W 0 2 6
C 5 0 4
C 4 0 5
C 4 1 8
C 8 1 9
C 4 4 3 C 4
3 7
R816
C 6 3 4
D602
D604
D 6 0 3
W028
R 6 2 3
C 8 0 2
D 8 0 1
D 8 0 2
W118
W 0 1 1
W1 1 9
C 6 2 6
W810
W 8 2 7
W 8 0 4
W 8 1 6
W 8 0 2
W 8 2 8
W 8 1 5
W 8 2 1
W 8 2 6
J201
W 0 9 8
CD802
PRINTED CIRCUIT BOARDSMAIN/CRT (INSERTED PARTS)
SOLDER SIDE
F-1
8/18/2019 Matsui 1409r Tv Sm
17/29
F-3
12
23
34
1 C 8 0 5
R 8 1 1
C 8 0 4
R 8 0 9
C 8 0 6
R 8 1 4
R 8 1 3
C 0 0 5
C 0 0 4
R 7 0 8
R 7 1 5
R712
C 7 0 4
C 7 0 3
R 7 1 1
R705 R 7 0 6
R 7 0 4
R 7 2 1
R 7 1 7
C 7 0 7
R 7 2 3
Q702
R 7 2 2
R601
Q351
C 7 0 5
R 5 2 1
R 1 1 8
R 1 1 7
C 1 1 4
C 1 1 3
Q102 R 1 3 0
R 1 3 2
R 1 1 9
C 1 1 5
R 1 2 9
Q101 R 1 2 0
C 1 0 4
R 1 3 3
R 1 3 4
C108 R 1 2 5
R 1 3 6
R122
IC101
R 1 1 1R103
R110
R 1 0 9
R 1 3 9
R 1 0 6
C 1 0 7
R115
R 3 5 4
R757
R 5 0 7
C 1 0 5
R 1 4 2
R 3 5 0
C 0 0 6
R633
R631
R 6 3 4
C 3 6 0
R 1 3 8
R 1 4 0
R352
R 5 1 2
R513
C513
R 1 0 8
C112
R 1 1 6
R 1 2 1
R 6 1 5
C 6 2 4
R 6 1 8
C 6 3 0
C 6 1 2
C 6 1 3
R 2 1 1
C 6 1 0
C 2 1 8
R213 C 2 0 3
C212R217
C215
R 2 1 5
Q204 R 2 1 6
R 2 1 4
C 2 0 4
C214
C 2 0 6
C 2 1 1
C611
R616R617
C 6 2 8
C629
R 6 2 6
R625
C 6 1 6
C 2 2 2
C 6 1 4
R612
R 6 1 3
R
6 1 4
R630
C 2 0 8
R 2 0 7
Q202
R 2 0 8
R209
R 2 1 0
R 2 0 5
C 2 0 7
R 2 0 3
R 2 0 1
R 2 1 8
Q601
R605
R 6 0 3
C 4 2 9
R405
R 5 2 4
C 6 2 7
R 6 2 1
R 6 2 2
R 5 2 5
R 1 1 3
C 6 3 2
C 6 3 3
R 6 3 9
R 6 3 8
R637
Q603
R356
R 2 0 6
R 2 0 2
Q505
R 0 0 6
C 6 3 7
Q203
Q201
R 3 5 9
R358
R 4 0 1
R 4 2 4
R 4 1 1
R519
C404
R 6 2 7
Q602
Q608 Q610 Q609
R 2 2 1
R640
R642
R641
R409
R 7 0 1
IC601
Q604
R 1 2 7
C 4 1 1
C 3 5 4
R 6 3 5
Q611
C 4 0 1
R 2 0 4
R 6 2 8
C638
Q103
R147
R 1 4 8
C 1 1 8
R 1 4 9
R611
Q703
Q704
R 7 1 8
R720
R 7 1 9
C 7 0 6
C227
R 4 2 0
R815
C639
W 8 0 6
C117
MAIN/CRT (CHIP MOUNTED PARTS)SOLDER SIDE
PRINTED CIRCUIT BOARDS
8/18/2019 Matsui 1409r Tv Sm
18/29
A B C D E F
A B C D E F
2
1
3
4
5
6
7
8
Q1012SC2412K
V-BUFFERQ1022SC2412K
H-BUFFER
D 0 0 1
H Z 3 0 - 3
L
G N D
B +
V o u
t
OS101
PIC-28143SY-2
1 2 3
R 1 3 8
6 8 K
R101
2.2K 1/4W
R 1 2 4
1 0 0 1 / 4 W
R 1 1 3
1 0 0
R 1 2 6
4 7 1 / 4 W
R 1 1 6
1 0 K
R 1 2 2
3 . 3
K
R106
2.2K
R139
1.2K
R103
820
R 1 4 2
4 . 7
K
R102
3901/4W
R 1 2 1
3 . 3
K
R 1 3 0
8 2 0
R 1 2 7 1
K
R111
4.7K
R 1 3 1
1 0 K 1 / 4 W
R 1 3 2
1 5 K
R 1 3 3
1 0 K
R109
10K R110
22K
R 118 100
R120
100
R 119 100
R 1 2 5
2 2 K
R 117 100
R 1 3 6
2 2 K
R10410K 1/4W
R114
2701/4W
R140
270
R 1 1 5
1 0 K
R146
470 1/4W
R147
560K R148
47K
R 1 4 9
5 6 K
R108
10K
R107 1001/4W
R 0 0 1
6 8 K
1 / 2 W
R 0 0 3
2 7 0 1 / 4 W
R 0 0 2
6 8 K
1 / 2 W
R 0 0 4
2 7 0 1 / 4 W
R 0 0 6
1 5 K
R 1 2 8
3 3 K 1 / 4 W
R 1 2 9
2 . 2
K
R 1 4 1
1 0 K 1 / 4 W
IC103
RES
1 2
C 1 0 3
1 0
2 5 V
K A
50
C 1 1 8 5 6 P C H
C112
0.01 B
C 1 0 7
0 . 0
1 B
C104
12P CH
C108
0.1 B
C105
12P CH
C 1 1 3
2 7 0 P
C H
C 1 1 4
2 7 0 P
C H
C 1 1 5
2 7 0 P
C H
C 1 1 7
5 6 0 P C H
C 0 0 1
0 . 0
2 2 M
C 0 0 4
2 2 0 P B
C 0 0 5
2 2 0 P B
C 1 1 0
0 . 1
F
5 . 5
V
C 1 1 1
3 3
6 . 3
V
K A
C101
1006.3V YK
C 1 0 2
4 . 7
5 0 V
K A
C106
150V KA
C 0 0 2
4 7 0
6 . 3
V
Y K
TU001 NJH3023M218
1 1 0 1
1
1 2
1 3
1 4
1 5
2 3 4 5 6 7 8 9
S W 1 0 6
S K H V B E D 0 1 0
C H U P
S W 1 0 7
S K H V B E D 0 1 0
C H D O W N
S W 1 0 2
S K H V B E D 0 1 0
V O L U P
S W 1 0 4
S K H V B E D 0 1 0
V O L D O W N
OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE:
L 1 0 1
3 3 u
H
L 0 0 1
1 0 u
H
TM101R25-1442
ANT001
TU-33AP
BT002
R03(AB)E_20_T
BT001
R03(AB)E_20_T
CC004 TP-IS-05
D107
SLR-342VCT32
STAND BY
X101
CSTS0800MG03-T2 1
2
3
D103
1SS133
I C 1 9 9 S - 2
4 C 0 4 B D P - L
A
M E M O R Y
1234
5 6 7 8
CP101W-D2506#01
1
2
3
4
5
6
IC101OEC6058A
MICON
1
1 0
1 1
12 13 14 15 16 17 18 19
2
20 21 22
2 3
2 4
2 5
2 6
2 7
2 8
2 9
3
3 0
3 1
3 2
3 3
343536373839
4
4041424344
5
6
7
8
9
Q103
2SA1037AK
SYNC SEPA
R.OUT
TUNER_AGC
TUNER_IF
SYNC_VIDEO
SDA
SCL
AFT
OSD-R
OSD-G
OSD-B
OSD-Y
TUNER_H
FOR_VCR
A_MUTE
OSD-R
OSD-G
OSD-B
OSD-Y
G-1
S D A
V C C
S C L
M O D E
FROM/TO 21PIN/SOUND
FROM/TO VIDEO/RBG SW
FROM/TO IF/CHROMA
TEST POINT
(MAIN PCB)MICON/TUNER SCHEMATIC DIAGRAM
NC
NC
4.84.80
0
0
4.8
0
21
54
3
5.0 0
5.0
0000
0
0 0 0
0
0
2.0
5.03.84.05.0
3.80.5 2.5 000000
0
0
0
0
0
5.0
5.0
5.0
5.0
2.7
4.8
5.0
2.4
5.0
5.0
4.9
NC2.65.0
3.84.0
5.0
5.0
5.0
5.0NC
4.9
NCNC
G N D
V C C
E 0
E 1
E 2
V S S
N C
14 ON TIME LED
13 STAND BY LED
12 9V POWER
NC
43 AKB WHITE
NC
22 H-SYNC
21 OSD Y 44 POWER
35 SCL
34 SOUND B
V D D
V S S
P A L / S E C
S D A
1 2 C O F F
O S D B
O S D R
O S D G
V S S
SOUND A
SD
REMORT
P_FAIL
RESET
XOUT
XIN
TEST
OSC OUT
OSC IN
V-SYNCFORTHED VCR
AFT
KEY
ATS
AV2
AV1
DEGAUSS
BLUE BACK H
A_MUTE
T_RESET
3 . 5
8 N T S C
NC
NC0
9.1
8.5
2.1
7
R.OUT
AGC
I2C OFF
I2C SDA
GND
I2C SCL
0 2
. 2 3
. 8 4
. 0 4
. 9 3 0
. 7 NCNCNCNCNC
A G C
A D R E S
S C L
S D A
V . S
B P L
B T L
I F
8/18/2019 Matsui 1409r Tv Sm
19/29
A B C D E F
A B C D E F
2
1
3
4
5
6
7
8
IS NON POLAR ONE. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
W 8 1 0
W 8 1 6
W806
W811
D 6 1 4
1 1 E 1 N
D615
1SS133
R 6 2 4
5 . 6
K + - 1
%
B 2 0 1
B L 0 2 R N 2 - R
6 2 T 4
L602
100uH
L603
100uH
I C 2 0 1
T B 1 2 5 4 N
C H R O M A
1 10 11 12 13 14 15 16 17 18 192 20 21 22 23 24 25 26 27 28
29
3
30313233343536373839
4
40414243444546474849
5
50515253545556
6 7 8 9
CF202
SFE6.0MB
C F 2 0 3
T P S 6
. 0 M B
OUTOUTGININ
CF201SAF39.5MZK220ZL
SAW FILTER
1 2 3 4 5
X 6 0 1
4 . 4
3 3 6 1 9 M H z
C 6 2 1
0 . 2
2
5 0 V
K A N P
L201
360K044
1 2 3
4 6
C F 2 0 4
M K T 4 1
. 5 M A 1 1 0 P
Q202
2SC2412K
T.V.Buf.
Q608
2SC2412K
OSD RED OUT
Q609
2SC2412K
OSD GREEN OUT
Q610
2SC2412K
OSD BLUE OUT
Q2042SC2814
IF Pre. AMP
Q2012SC2412K
EXT AUDIO DRV.
D 6 0 2
M T Z J 6
. 8 B
D 6 0 3
M T Z J 6
. 8 B
D 6 0 4
R 2 2 1
1 K
R 6 2 8
1 0 K
R
2 1 5
6
. 8 K
R 2 1 4
2 . 2
K
R 2 1 3
1 0 0
R203
100
R 2 0 8
2 . 2
K
R 2 0 7
3 . 3
K
R 2 0 5
5 6 0
R 2 0 4
5 6 0
R 2 0 1 1
0
R 2 0 2 1
K
R 2 1 6
4 7
R 2 1 2 7
5 1 / 4 W
R 2 1 7
1
. 2 K
R 6 0 2
3 3 K
1 / 4 W
R 2 1 8
1 0 0
R 6 1 5
2 . 2
K
R 6 3 7 2
. 7 K
R 6 3 8
2 . 7
K
R 6 3 9
2 . 7
K
R 6 1 6
1 0 0
R 6 1 7
1 0 0
R 6 1 8
1 0 0
R206
330
R 2 1 0 1
K
R 2 0 9
3 3 0
R 2 1 1
1 5 0
R 6 2 3
3 9 0 1 / 4 W
R 6 2 5
1 8 K
R 6 2 6
8 . 2
K
R 6 1 2
1 K
R 6 2 1
1 0 0
R 6 2 2
1 0 0
R630
270
R614
2.2K
R 6 1 3 1
K
C 6 0 9 0
. 2 2
5 0 V
K A
C 2 2 3
0 . 4
7
5 0 V
K A
C 2 1 6
4 . 7
5 0 V
Y K
C 2 1 7
1 0
1 6 V
K A
C 6 4 0
1 0
5 0 V
K A
C 2 1 9
2 . 2
5 0 V
K A
C 2 2 1
1
5 0 V
K A
C 6 1 5
1
5 0 V
K A
C 2 0 9
2 2
6 . 3
V
K A
C 2 0 5
1 0 0 0
1 0 V
Y K
C 2 0 2
1 0 0
1 6 V
Y K
C 6 0 5
1
5 0 V
K A
C 6 3 1
0 . 2
2
5 0 V
K A C
6 2 0
1
5 0 V
K A
C 6 2 5
1
5 0 V
K A
C 6 2 3
1 0
5 0 V
Y K C
6 4 1
1 0 0
6 . 3
V
Y K
C 6 3 5
1 0 0
1 6 V
Y K
C 6 3 4
1 0 0
1 6 V
Y K
C210
1006.3V YK
C 6 2 8
_ 1
0 . 0
0 2 2 B
C 6 1 1
1 0 P C H
C 6 1 7
0 . 1
F
C 6 1 8
0 . 1
F
C 6 1 9
0 . 1
F C 2 1 8
0 . 0
1
B
C 6 1 0
_ 1
0 . 0
0 2 2 B
C211
0.01 B
C 6 3 0
0 . 0
0 8 2 B
C 6 1 3
0 . 1
F
C 6 1 4
0 . 1
F C 2 2 2
_ 1
0 . 0
0 1
B
C 2 0 8
0 . 1
B
C 2 0 7
0 . 0
1 B
C 6 2 7
0 . 0
1 B
C 6 2 9
0 . 1
B
C 6 1 2
0 . 0
1 B
C 2 1 5
0 . 0
1 B
C 2 2 7
0 . 0
1 B
C 6 3 8
_ 1
C 6 3 9
0 . 1
F
C 6 3 7
_ 1
0 . 0
0 1
B
C 6 2 6
0 . 4
7 T F
C214
10P CH C 2 1 3
0 . 0
1
M
C212_1
0.001 BC204
0.022 B
C 2 0 3
0 . 0
2 2
B
C 2 0 1
0 . 0
1
M
C633
220P B
C 6 2 2
0 . 1
F
C 6 1 6
0 . 1
F
C632
220P B
C 6 2 4
0 . 0
1 B
C 2 0 6
0 . 0
1 B
OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME THE DC VOLTAGE AT EACH PA
WITH THE DIGITAL TESTER WH
WAS RECEIVED IN GOOD CON
NOTE:
L206
0.33uH L 2 0 3
2
. 2 u
H
L 2 0 4
1 8 u
H
L202
12uH
Q203
2SA1037AK
T.V.DR.
Q604
2SA1037AK
VIDEO BUF.
A F T
S C L
A F C
S D A
H_
O U T
A V
_ A U D I O
A V
_ V I D E O
S Y N C
_ V I D E O
T U
_ V I D E O
_ O U T
TU_VIDEO_OUT
AV_VIDEO
AV_AUDIO
TU_AUDIO_OUT
AUDIO_OUT
P.CON+9V
P.CON+5V
GND
T
U N E R
_ A G C
A - Y
A - R
A - G
A - B TUNER_IF
FROM/TO POWER
G-3
(MAIN PCB)IF/CHROMA SCHEMATIC DIAGRAM
E X A U D I O
D C H F
P I F t a n
k
T V I N
L O O P F I L T E R
E X T I N
C b I N
C r
I N C I N
M O N O U T
Y I N
S Y N C I N
S D A
S C L
D l g G N D
H .
O U T
H V c c
( 9 V )
F B P I N /
S C P O U T
H . A
F C F i l t e r
B L A C K D a t
I F V c c
R I P P L E F I L
A U D I O O U T
I F G N D
I F I N
I F I N
I F A G C
A P C F i l t e r
X ’ t a l
C M O U T
R G B V c c
( 9 V )
E X T
. R I N
E X T
. G I N
E X T
. B I N
Y / C G N D
R O U T
G O U T
B O U T
1 K I N
V R A M P
V N F B
V O U T
r e f R
A B C L I N
S I F O U T
S I F I N
R F A G C
H C O R R E C T I O N
S I F I N /
A F T O U T
I F D E T O U T
P I F t a n
k
D E A M P
N C
Y / C V C O ( 5 V )
D C R e a
t e r
D l g V C O
4.9 3.8 8.4 3.7 0 1.3 0.2 0 1.9 2.73.1
3.2 2.1 2.12.108.93.2 0 2.6 2.6 2.6 0 3.9 4.8 1.1 1.0 6.1
1.6 6.98.91.803.43.42.73.22.62.52.44.04.72.02.32.31.51.52.62.13.93.94.44.02.02.03.0
4.0
3.4
O S D Y
10
14
09.1
2.4
09.1
2.4
09.1
2.4
FROM/TO 21PIN/SOUND
8
15
1.5
0.8
7.0
4.0
4.68.9
9.1
9 11
1.6
0
2.3
2.0
0
2.6 13
12
NCNC
9.1
8/18/2019 Matsui 1409r Tv Sm
20/29
A B C D E F
A B C D E F
2
1
3
4
5
6
7
8
DESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONES
ARESINCE THESE PARTS MARKED BYCAUTION:
DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE
ETANTLES PIECES REPAREES PAR UNATTENTION:
R 5 4 2
1
1 W
R 5 0 4
3 3
3 W
R505
220 1WS
DG
Q5012SK2480
SW
IC506 TLP621(D4-GR-LF2)
FEED BACK
1
2 3
4
V R 5 0 1
3 3 0
F501
T4A_L_250V
FH501
EYF-52BC
FH502
EYF-52BC
2
1
L5038R140027
CP501 THL-P03P-B1
1
2
R501
5.6 7W
HS501
763WAAA022
CP502
TV-50P-02-A1
1
2
P
H
TH501
PTH451C262BF140M
1
2
3
CAUTION: DIGITAL TRANSISTOR
L5010R8A393F28Y
12
34
T5028129054
1
10
11
12
13
14
15
16
2
3
4
5
6
7
9
SW501SDDFC30400
1
2
3
4
5 6
2
1
CD5011206635818
AC230V-240_50Hz
W802 W801
D 5 1 2
1 S S 1 3 3
D 5 0 8
1 S S 1 3 3
D 5 0 4
R M 1 1 C - E
I C
D 5 0 3
R M 1 1 C - E
I C
D 5 0 1
R M 1 1 C - E
I C
D 5 0 2
R M 1 1 C - E
I C
D518
1SS133
D516
21DQ09N
D513
11EQS04N
D505
11EQS04N
D510
RU2AM
D511
RMPG06J
D519
1SS133
D514
1SS133
D521
1SS133
R 5 1 8
2 . 2
K
+ - 1
%
B 5 0 1
B L 0 1 R N 1 - A
6 3
B504
BL01RN1-A63
Q5022SC2120Y
PROTECT
Q503
2SD863
5V SW
Q507
2SC1740SP
FEED BACK SWITCHING
D 5 0 6
M T Z J 1 5 B
D 5 0 9
M T Z J 1 8 B
D 5 0 7
M T Z J 1 5 B
D 5 2 8
M T Z J 5
. 6 B
R 5 0 8
2 . 7
K
1 / 4 W
R 5 1 2
2 . 2
K
R 5 1 3
5 6 0
R 5 0 6
6 8 0
1 / 4 W
R 5 1 1
2 . 2
M 1 / 4 W
R 5 1 0
2 . 2
M 1 / 4 W
R520
150K 1/2W
R 5 1 4
5 6 K 1 / 2 W
R 5 0 2
1 . 5
M 1 / 2 W
R 5 1 5
2 . 2
K
1 / 4 W
R 5 0 9
2 . 2
K
1 / 4 W
R523220 1/4W
R 5 2 4
R 5 2 5
R507
10K
R 5 2 1
R 5 1 6 3 3 0
1 / 4 W
R519
330
C511_1
150V KA
C 5 2 6
1 0 0
4 0 0 V
U S P
C 5 0 1
0 . 0
0 3 3
M
C503
0.0012KV B
C502
0.0012KV B
C 5 0 7
0 . 0
0 2 2
2 5 0 V
K X
C 5 1 4
6 8 0 P
2 K V
B P
C509
0.047 M
C531
0.01 M
C 5 1 8 0
. 2 2
E C Q U L
C 5 0 5
0 . 1
2 5 0 V
E C Q U L
C 5 2 9
0 . 0
0 2 2
2 5 0
V
K X
C520470P500V B
C512_1
470P500V B
C516
470P500V B
C517
0.0012500V B
C 5 0 4
1 T F
C 5 1 3
_ 1
0 . 0
0 1 B
C 5 2 2
4 7 0
1 6 V
Y K
C 5 1 5
4 7 0
1 6 V
Y K
C 5 2 7
4 7
1 6 V
Y K
C 5 1 9
1 0 0 0
2 5 V
Y K
C 5 2 1
2 2 0
1 6 0 V
P R
C 5 2 3
C 5 1 0
4 7
1 6 V
Y K
OF PRINTNOTE:THIS SC
OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
BLUE
BROWN
BLUE
BROWN
G-5
(MAIN PCB)POWER SCHEMATIC DIAGRAM
NC
NC
NC
5.0
0
0.3
0.3
320
4.3
16
17
NC NC
8.8
8.18.2
11.6
10.9
7.7
5.6
6.2
+ B A D J .
8/18/2019 Matsui 1409r Tv Sm
21/29
A B C D E F
A B C D E F
2
1
3
4
5
6
7
8
S101
VIDEO
8
E8E25
E12
GND
TERHEAAFC
B+
GND
ABL
GND
COLHV
F
S
FB401
3214029F
1
10
11
2
3
4
5
6
7
8
9
Q401_12SD2599
H.OUTPUT
CD801127C140022
CP8061
CP801 TBS-X01X-A1
1
B
G
R
11
6
8
10
9
175
V801A34AGT13*07
T401
305Y001
1
2
3 4
6
I C401 AN5539NV-OUT
1 2 3 4 5 6 7
R429
3.3 1W
CP401
B05B-DVS
1
2
3
4
5
CP802A51048-1000
1
10
2
3
4
5
6
7
8
9
CP802B51048-1000
1
10
2
3
4
5
6
7
8
9
DESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONESSINCE THESE PARTS MARKED BYCAUTION:
DANS LA NOMENCLATURE DESN’UTILISER QUE CELLS DECRITDANGEREUSES AN POINT DE VLES PIECES REPAREES PAR UNATTENTION:
HS401763WSA0004
W897W812
W813
W 8 0 4
W828
D403
11E1N
D 4 1 0
A U 0 2 A - E
I C
D 4 0 5
A U 0 2 A - E
I C
D407
1SS133
D406
1SS133
R 4 1 7
1 0 K
+ - 1
%
L 8 0 1
1 0 0 u
H 0 6 0 7
Q4022SC2271
H.DRIVE
D 4 0 4
M T Z J 6
. 2 B
R445 150K 1/4W
R 4 2 1
6 8 K
1 / 4 W
R 4 0 7
1 . 8
1 / 2 W
R408
1K1/4W
R 4 2 4
3 9 K
R409
150K
R411
56K
R420
27K
R415
3.3K 1/4W
R418
6.8K 1/4W
R 4 1 0
3 3 0
1 / 2 W
R 4 0 5
1 0 K
R414
2.2K 1/4W
R422
820 1/4W
R403
22K 1/4W
R 4 2 7
1 0 0 1 / 4 W
R 4 4 6
4 . 7
K
1 / 2 W
R 4 0 1
1 0 0
R404
15K1/4W
R406
1.8K1/4W
C 4 1 4
1 0 0
3 5 V
M H E
C 4 4 8 2
2
2 0 0 V M
H E
C 4 0 3
4 7 0
3 5 V
Y K
C 4 0 9 1
0 0
1 6 0 V
M H E
C 4 4 6
1
1 6 0 V
M H E
C 4 3 5
0 . 1 1
0 0 V T
F
C405
1 TF
C 4 3 0
0 . 1 1
0 0 V T
F
C 4 2 9
_ 1
0 . 0
0 2 2
B
C411_1
0.001 B
C 4 2 0
0 . 0
0 1
5 0 0 V
B
C 4 0 7
5 6 P
S L
C406
22P500V SL
C 4 3 7
0 . 3
3
2 5 0 V
P M S
C 4 4 3
0 . 0
0 4 7
1 . 6
K V
E C W H
C 4 4 0
4 7 0 P
5 0 0 V
B
C439
22P500V
SL
C 4 0 1
_ 1
1 0 0 P C H
C 4 0 4
0 . 0
4 7 B
C 8 1 9
0 . 0
0 1
2 K V
B
C 4 1 8
2 2 0 0
2 5 V
M H E
C 4 2 5
4 . 7
5 0 V
K A
C 4 1 0
4 7 0
3 5 V
Y K
TP401
G.OUT
R.OUT
B.OUT
AKB_WHITE
V_FEEDBACK
V_OUT
ABCL
H_OUT
AFC
VD
AKB_WHITE
AFC
P.CON+9V
P.CON+5V
H.DRV+B
+B_130V
GND
SCREEN
G-7
(C
THERMALPROTECTION
(MAIN PCB) DEFLECTION/CRT SCHEMATIC DIAGRAM
NC
0.3
0
137.0
130.0
0
0
0NC
PCB010
FOCUS
SCREEN
NC
TMX466
NC
23
22
GND+
AMP-
PUMPUP
VCC
2.123.92.42.424.212.40
1
NC
GND
G.OUT
R.OUT
B.OUT
180V
HEATER
GND
NC
VCC 9V
AKB
180V
R.OUT
B.OUT
HEATER
GND
NC
GND
G.OUT
VCC 9V
FROM/TO CRT
21
0
0
130
20
0.3
27.0
0
19
18
FROM/TO POWER
FROM/TO MI CON/TUNER
FROM/TO IF/CHROMA
NC
FOCUS
NC
FROM/TO DEFLECTION
TCX324
PCB110
8/18/2019 Matsui 1409r Tv Sm
22/29
A B C D E F
A B C D E F
2
1
3
4
5
6
7
8
IS NON POLAR ONE. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP THE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
J7050350_9982_05
1
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2
2 0
2 1
3
4
5
6
7
8
9
I C351 AN7523
SOUND AMP
1 2 3 4 5 6 7 8 9
T
W827
W821
W814
W815
W826
B351BL01RN1-A63
L703
100uH
C353
2.250V KANP
Q3512SC2412K
BUFFER
Q701
2SC1815Y
VIDEO_BUFFER
Q7032SC2412K
VIDEO_AMP
D 7 0 6
M T Z J 6
. 8 B
R 3 5 4
4 7 K
R757
100
R 7 0 1 7
5
R 7 5 6
7 5 1 / 4 W
R 7 1 8
1 K
R 7 2 0
1 K
R719
1.2K
R717
100
R352
4.7K
R357
56 1/2W
R358
12K
R 3 5 6
6 8 0 K R
3 5 5 3
. 9 K
1 / 4 W
R 3 5 0
5 . 6
K
R 3 5 9
1 2 K
R 7 0 6 7
5
R712
1K
R708 75
R711
1K
R 7 0 4 6
8
R 7 0 5 7
5
R 7 1 0
5 . 6
K 1 / 4 W
R 7 1 5 7
5
C 3 5 9
1 0 0
1 6 V
Y K
C759
1050V YK
C 3 5 7
1 0
5 0 V
Y K
C 3 5 2
1 0
5 0 V
K A
C356
1050V KA
C 3 5 1
4 7 0
1 6 V
Y K
C 7 0 5
4 7 0 P B
C 7 0 4
4 7 0 P
B
C 7 0 6
2 2 P C H
C70
0.2
C 7 0 3
4 7 0 P B
C 3 6 0
0 . 0
0 4 7
B
C 3 5 0
0 . 0
0 3 9 X
C354
470P B
C 7 0 8 1
0 0
1 6 V
Y K
C702
4706.3V YK
OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE:
L753
10uH
L702
10uH
L701
10uH
Q7042SA1037AK
VIDEO_AMP
AUDIO_OUT
TU_VIDEO_OUT
TU_AUDIO_OUTAV_VIDEO
AV_AUDIO
G-9
(MAIN PCB)
21PIN/SOUND SCHEMATIC DIAGRAM
NC
+
7.5 4.0 0 4.0 6.0 1.4 0 NC 0
NC
2.0
5.0
2.7
0
0
5.4
2.21.6
4.3 4.3
5.0FROM/TO IF/CHROMA
27
8/18/2019 Matsui 1409r Tv Sm
23/29
A B C D E F
A B C D E F
2
1
3
4
5
6
7
8
CAUTION: DIGITAL TRANSIST
Q602
DTA114EKA
RGB SW
CAUTION: DIGITAL TRANSISTOR
Q611DTC144EKA
RGB OFF SW
W808
W824
W809
Q6032SC2412K
SWITCHINGR635
4.7K
R627
2.2K
R609
1K1/4W
C604
3.350V YK C603
3.350V YK C602
3.350V YK
OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE:
A-B
A-G
A-R
A-Y
G-11
(MAIN PCB)
VIDEO/RGB SW SCHEMATIC DIAGRAM
0
0.6
0
0 4.9
0.6
4.1
0.1
0
FROM/TO IF/CHROMA
8/18/2019 Matsui 1409r Tv Sm
24/29
A B C D E F
A B C D E F
2
1
3
4
5
6
7
8
Q8512SC1815Y
BUFFER
Q8522SC2412K
SYNC BUFFER
R875
56K
R865
100
R864
100
R 8 5 2
1 K
R 8 5 3 1
K
R 8 5 5 1
K
R 8 5 7 1
K
R854
330
R 8 6 7
1 5 K
R 8 5 1
2 . 2
K
R 8 8 1
1 5 0
R 8 8 0
2 2 K
R 8 7 1
2 2 K
R890
10K
C 8 6 0
1 0 0 P C H
C 8 5 8
1 0 0 P C H
C 8 5 2
0 . 1
M
C 8 6 7
0 . 0
1
B
C861
0.01 B
C855
0.022 F
C 8 6 8
1 0 0
6 . 3
V
Y K
L 8 5 1
1 0 u
H
W864
W 8 5 8
W860
W853
W854
W857
W861
W859
W 8 6 3
C 8 6 9
2 2
1 6 V
N P
THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE:
B850
BL02RN1-R62
OF PRINTING AND SUBJ ECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
IC850 ET106
DECORDER IC
1
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2
2 0
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
3
4
5
6
7
8
9
CP852BIMSA-9130S-05L
1
2
3
4
5
CP851BIMSA-9130S-06L
1
2
3
4
5
6
C870
10016V YK
AVCC
TEST2
NC
CSB
TCLK.
TDATA
TEST4
TEST1
DGND
CLK.IN
RSTB
VIDEO
SYNC
TEST5
G-13
(T’TEXT PCB) T’TEXT SCHEMATIC DIAGRAM
(CP852)
FROM/TO VIDEO/RGB SW
(CP851A)
NC
NC
FROM/TO VIDEO/RGB SW
1.0
4.0
3.5
3.5
4.9
4.9
4.9
4.5
4.94.9
4.2
4.9
2.2
2.2
1.1
1.1
DVCC
WIND
TEST3
SCL
SDA
BLANK
BLUE
GREEN
RED
AGND
RGB SET
REF.
FLAG1
FLAG2
0
0
0
0
0
0
0
0
0
0
0
0
0
4.9
0.3
SDA
SCL
5V
SYNC
GND
2.1
1.46
4.6
TEXT B
TEXT G
TEXT R
TEXT Y
AV VIDEO 1
T TEXT RESET
8/18/2019 Matsui 1409r Tv Sm
25/29
4 1.0V 20µs/div 10 10mV 10µs/div
5 1.0V 5ms/div
The following waveforms were measured at the point of the correspondingballoon number in the schematic diagram.
NOTE:
WAVEFORMS
1 1.0V 200µs/div
8 500mV 500µs/div
3 1.0V 50ns/div 9 500mV 10µ
s/div
MICON/TUNER
H-1
2 1.0V 200µs/div
11 500mV 10µs/div
7 1.0V
Recommended