ADSL 2+新西兰NEW

8/6/2019 ADSL 2+ NEW

1/14

ADSL 2+

USER'S MANUAL

PLEASE READ THIS MANUAL CAREFULLY BEFORE USE

A D S L

8/6/2019 ADSL 2+ NEW

2/14

8/6/2019 ADSL 2+ NEW

3/14

Introduction

2

Pentium 233MHz64M or more than 64M storageEthernet network card 10M Base-TWIN9X WIN2000 WINXP WINME WINNT

Indicator lamp Status Function

Power supply

Lighting MODEM power on

ACT Lighting

Blinking

Blinkingslowly

MODEM have connected with PC network interface and HUB

MODEM have connected with physical layer of office

terminalMODEM have connected with physical layer of officeterminal

Connecting

Data

BlinkingTransmitting data between MODEM and PC networkinterface or HUB

Blinkingfast

Blinking

MODEM is shaking hands with physical layer of officeterminalMODEM is receiving and sending data

Please refer to all relative information provided by the productsupplier. This information is available to ADSL Modem config-uration. User inputs this information into corresponding positionwhen installation .

VPIVCIVCMUX or LLCMUX encapsulationProtocol modesModem modes ANSI T1.413 G.LITE G.DMT

User name, password and password protocol

4. ADSL LED indication

Introduction

3

5. Rear board description

Interface Function

Power jack Insert electric power

Reset

Netinterface

LINE

MODEM RESET key. Touch lightly for three times continuouslyby needle ,then hardware reset .At this time, All MODEM LEDwill light ,and after a while put out, and MODEM reboot andreset to factory defaults.(NOTE: To reset hardware, the MODEM information set atpresent will be cleared, and back to factory defaults)

Rj45 network line interface, connecting pc or HUB throughnetwork line.

ADSL telephone line interface

ACT Power DataLink

8/6/2019 ADSL 2+ NEW

4/14

Hardware setup

4

Connect ADSL MODEM with pc over the following way:1. If connecting separator Phone line of separator connects with phone line jack, PHONE access of separator connects with telephone, MODEM access

of separator connects with LINE access of ADSL MODEM.

Chapter 2: Hardware setup

S e p a r a t o r

2. If no separator, ADSL phone line connects with LINE accessof ADSL MODEM.

3. Make the power on, indicator LED will light and boot ADSLMODEM .

MODEM Parameter configuration

5

1. Login

Chapter 3: MODEM Parameter configuration

(2) Login on web interface

(1) PC network card IP address configurationFirst install network card well, and set the IP address. Pleasecheck MODEM DHCP server factory defaults in appendix.

OpenHttp://192Microsoft Internet Explorer, Netscape Navigator, and

input .168.1.1 Modem IP address, then pressENTER key on pc to access following interface:

If in ON state, please set IP address as automaticassignment state .If in OFF state, make cp and

in the same network field (eg, if MODEM IP addressis 192.168.1.1,the pc IP add ess should be 192.168.1.X ,Xmeans any number from 3 to 255 .)Make MODEM power on and pc require a reboot

please IP address MODEM IPaddress

r USB

8/6/2019 ADSL 2+ NEW

5/14

6


Enter username and password, then click OK key to access webconfiguration interface .

After username and password entered and detected correct bysystem, main pages will display as :following

Default configuration :IP address : 192.168.1.1Username : adminPassword : admin

2. Home pages

admin


7

8/6/2019 ADSL 2+ NEW

6/14

8


3. Protocol and parameter configurationSelect Local ADSL protocol and relative information provided by

ADSL supplier .

Now we make a brief introduction to you on RFC1483 Bridge(EOA) and PPPoE. For more details about other protocols, pleasecontact MODEM supplier and get relative configuration ways .

Generally, ADSL supports protocols are shown asfollowing:

Ethernet over ATM RFC1483 Bridge EOAPPP over Ethernet RFC2516 PPPoEPPP over ATM RFC2364 PPPoARFC 1483 Router IPOAIP over ATM RFC1577 IPOA


9

4. PPP over Ethernet (RFC2516) (PPPoE) configuration

8/6/2019 ADSL 2+ NEW

7/14

8/6/2019 ADSL 2+ NEW

8/14

12

MODEM Parameter configuration MODEM Parameter configuration

13

(2) Permanent saveIf user want to save these settings into modem chip, so thesesettings will not be lost after turning pc on again. User mustenter management page to save them.

Click Commit button to st ore configuration.Click Reboot button to restart modem.

Under the current page, press Submit key to enter.

NOTE:1. If login to internet by 1483 Bridge of static IP address ,

please input IP address and other information providedby ADSL supplierinto pc network card .

2. If in dial-up mode, after configurating ADSL modem, then

install the third dial-up software and connect it withInternet (for example: Eternet 300, T500, WinPoET).Under WinXP, user can use it's built-in dial-up software .Refer to information on page 20 for more details .

Eternet

6. DHCP Protocol

means d h c p .DHCP ynamic ost onfiguration rotocol

(1) DHCP server

Select DHCP server from LAN and enter DHCP server configuration interface, see the figure below:

DHCP server can assign automatically IP address to DHCPclient through modem. If using single pc connecting with a mod-em, it is not necessary to use DHCP server, but pc network cardTCP/IP protocol configuration is different .If many pc connectingwith a modem to share network line ,DHCP server is indispens-able.Before changing ADSL modem IP address or lack of IP addressat present, user should renew DHCP server range .

Select Management page and click Commit&reboot button .

8/6/2019 ADSL 2+ NEW

9/14

14

MODEM Parameter configuration MODEM Parameter configuration

15

Click icon to delete current DHCP server range.

Click Add button to renew DHCP server range .

Select DHCP mode from LAN option and enter DHCP modeinterface, then select DHCP server item from DHCP modeoption, see the figure below:

NOTE: Only write start IP and end IP address. Other infor-mation need not to be changed .

Save all configurations with the same way which is used inpermanent save sectionNOTE: If want to change modem IP address ,after changingit, save them together .

(2) DHCP ReplaySelect DHCP relay option from LAN to make modem as reapea-ter, so pc gets a dynamic IP address from ISP. This configurationis suitable for RFC1483 dynamic IP address connecting internet.

Select DHCP relay item from LAN option and enter DHCPrelay configuration interface as shown in figure below:

Select eth-0 option ,then click Add button at right side .Click Submit button

Replay item .

Select DHCP mode from LAN option and enter DHCP mode

interface ,then select DHCP see the figurebelow:

8/6/2019 ADSL 2+ NEW

10/14


16 17

Save all current configurations in the same way which is

used in permanent save section .

NOTE: This configuration is finished ,set pc network

card IP address as IP dynamic assignment .

(3) No DHCPSelect DHCP mode from LAN option and enter DHCP mode

interface, then select NONE option .Save the configuration in the same way which is used inpermanent save section .

NOTE: Make pc network card IP address and modem IP add-ress in the same network field (e.g.192.168.1.X)

Change pc gateway for modem IP address (e.g.192.168.1.1)Enable DNS and configurate DNS server well .

1. Problem 1 : All indicator LED do not light . Solution : Check if the power cord is connected properly.

Chapter 4: Troubleshooting

3. Problem 3 : LINK LED do not lightSolution : Check if phone line is connected with ADSL se-

parator and ADSL LINE interface properly .

2. Problem 2 : ACT indicator LED do not light .

Solution :Check if network line is connected with pc network card inter-face or HUB /Switch properly .Check if pc or HUB is in use state and works normally .If ADSL connecting with single pc, please use parallel line ;If ADSL connecting with HUB or Switch, please use doubleline .

4. Problem 4: LINK LED is lighting ,but not login internet Solution : Check if VPI/VCI is correct ,as well as username ,

password.

5. Problem 5: PC does not access modem web pages .

Solution :1) Check if pc can communicate with modem normally .

The flow of the work is as following :Click Start Run button on pc desktop, using LAN IP ad-dress of Ping modem item in Ping command .Take a example: Ping 192.168.1.1(modem IP address).

Troubleshooting

8/6/2019 ADSL 2+ NEW

11/14

Troubleshooting

18 19

6. Problem 6 : PC can not open web page . Solution : Check if modem configuration is correct.

2) Check if pc IP address and modem IP address is in the samenetwork field .If network card IP address is appointed ,make pc IP address

and modem IP address be in the same network field (e.g. 192.168.1.X) .Set gateway as modem IP address (192.168.1. 1) .If network card IP address is automatically assigned, check if modem DHCP server is on state ,and if IP address appointedby DHCP and modem IP address is in the same network field.The flow of the work is as following :Click Start Run button on pc desktop, using WINIPCFGcommand to view network card IP address .

If Ping do not be communicated ,please check if the networkis suitable for modem and each line is connected properly .

8. Problem 8: The application program speed is error. Solution: Check if the line is connected properly .Please click Refresh key to refresh latest modem configurations.

7. Problem 7: After automatic configurating, don't login internet ,no reentry configuration interface .

Solution: Press RESET key for 3 times continuously, thenreset parameters by application program or entering WEBconfiguration interface. IP address is 192.168.1.1 .

Accessories : Connect using a dial-up modem Exception for methods above, under WIN XP system, User can create dail-up.The flow of work is like this:

Firstly, Click Start all programes Accessories Communication Create connecting wizard , then display

following window :

Create dial-up under WIN XP

8/6/2019 ADSL 2+ NEW

12/14

20 21

Secondly, Select Connect to INTERNET option, and then clickNext .


Thirdly, Select Set up my connection manualy option, and thenclick Next .

Forthly, Select Broadband connecting with username andpassword option, and then click Next key .

Fifthly, Input ADSL (at random) in ISP name column .

Sixthly, Input ADSL account and password, then click Next key


8/6/2019 ADSL 2+ NEW

13/14

22


23

Seventhly, select Add a shortcut to this connecting to mydesktop , then click Finish button. See the figure below :

Eighthly XP will create dial-up icon at the desktop, user candouble click this icon to connect to the internet.

The following information is ADSL MODEM factory parameter ,please refer to them for more details :

Modem IP address 192.168.1.1PVC configuration :VPI0/VCI0 : 0/35VPI1/VCI1 : 8/35VPI2/VCI2 : 8/81

VPI3/VCI3 : 0/32Encapsulation: LLCMUX

Factory defaults

8/6/2019 ADSL 2+ NEW

14/14

Protocol configuration : RFC 1483 BridgeModem mode : MULTI(AUTO)DHCP configuration :DHCP server : ONDHCP server rangeStart IP address : 192.168.1.3Termination IP address : 192.168.1.34


24

If want to reset to factory default, in modem working state,pressRESET continuously three times with needle on rear board, the

ADSL modem hardware will return to factory defaults .

Documents

ADSL 2+新西兰NEW