Upload
ravikumarrk
View
753
Download
133
Tags:
Embed Size (px)
DESCRIPTION
anti bag snatching alarm
Citation preview
ANTI-BAG SNATCHING ALARMG.SRINIVASULU V.SRIKANTH
09491A04A9 09491A04A8
CONTENTS
INTRODUCTION
COMPONENTS
CIRCUIT DIAGRAM
EXPLANATION
ADVANTAGES
APPLICATIONS
CONCLUSION
INTRODUCTION
When a burglar tries to snach the bag,it sounds a loud alarm,simulating a police horn.
This will draw the attention of other passengers and the burglar will be easily caught.
In sttandby mode the circuit is provided with a lock but when a burglar tries ti snach it, the circuit turns into unlocked mode to sound a loud alarm,simulating a poloce horn.
This circuit consists of three ICs.
They are ICI CA3140(ICI),which acts as a comparator,IC2 NE555 which acts as monostable multi-vibrator and IC3 UM3561 which is a complex ROM with inbuilt oscillator.
A single stage transistor BD139 acts as loud speaker to sound a loud police horn
COMPONENTS
Resistors (all ¼-watt, ± 5% Carbon)
R1, R2, R3 = 100 KΩ
R4, R6 = 10 KΩ
R5 = 10 MΩ
R7 = 330 Ω
R8 = 220 KΩ
R9 = 1 KΩ
VR1 = 10 MΩ
Capacitors
C1, C3 = 0.0047 µF
C2 = 4.7 µF/16V
C4 = 0.01 µF
Semiconductors
IC1 = CA3140 (operational amplifier)
IC2 = NE555 (timer IC)
IC3 = UM3561 (complex ROM with an inbuilt oscillator)
T1 = BD139
ZD1 = 3.3V 500mA
Miscellaneous
SW1 = ON/OFF switch
L1 = speaker 8Ω 1W
CIRCUIT DIAGRAM
EXPLANATION
In the standby mode, the circuit is locked by a plug and socket arrangement (a mono plug with shorted leads plugged into the mono-jack socket of the unit). When the burglar tries to snatch the bag, the plug detaches from the unit’s socket to activate the alarm.
The circuit is designed around op-amp IC CA3140 (IC1), which is configured as a comparator
The output from pin 6 of IC1 is fed to trigger pin 2 of IC NE555 (IC2) via coupling capacitor C1 (0.0047 µF). IC2 is configured as a monostable.
When there is an attempt at snatching, the plug connected to the circuit de- taches. At that moment, the voltage at the inverting input of IC1 exceeds the voltage at the non-inverting input and sub- sequently its output goes low
Resistor R7 (330 ohms) limits the cur- rent to IC3 and zener diode ZD1 limits the supply voltage to IC3 to a safe level of 3.3 volts. Resistor R9 limits the cur- rent to the base of T1
The alarm tone generated from IC3 is amplified by transistor T1. A loudspeaker is connected to the collector of T1 to produce the alarm.
The alarm can be put off if the plug is inserted into the socket again. Transistor T1 requires a heat-sink.
Resistor R7 (330 ohms) limits the current to IC3 and zener diode ZD1 limits the supply voltage to IC3 to a safe level of 3.3 volts. Resistor R9 limits the current to the base of T1.
ADVANTAGES
SAFE AGAINST VALUABLE ITEMS IN BAG
SIMPLE AND HANDY
ALARM FOR EASY IDENTIFICATION
APPLICATIONS
CARRY IMPORTANT ITEMS IN BAG SAFELY
NO WORRY WHILE TRAVELLING FOR LOSS OF ITEMS IN BAG
CONCLUSION
The circuit kept in your bag or suitcase sounds a loud alarm, simulating a police horn, if someone attempts to snatch your bag or suitcase.
This will draw the attention of other passengers and the burglar can be caught red handed
QUERIES????????
THANK YOU