API 570 Piping Inspection (ไทย)

  • View
    4.530

  • Download
    216

Embed Size (px)

Text of API 570 Piping Inspection (ไทย)

Doc. No.: TD-570A-03 Page 1 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 1 78 onor ervice HS1.1 (General Application) 51.1.1 (Coverage) 51.1.2 51.1.3 51.2 (Specific Applications) 61.2.1 API 570 61.2.2 API 570 61.3 Fitness-For-Service (FFS) 84.1 (General) 184.2 API (API Authorized Piping Inspector Qualification and Certification) 184.3 (Responsibilities) 184.3.1 / (Owner/User) 184.3.2 Piping Engineer 204.3.3 (Repair Organization) 204.3.4 Authorized Piping Inspector 204.3.5 205.1 Risk Base Inspection 215.2 225.3 (Corrosion) (Crack) 225.3.1 Injection points 235.3.2 Deadlegs 245.3.3 Corrosion under insulation (CUI) 245.3.4 (Soil-to-air (S/A) interfaces) 265.3.5 localized corrosion 261 (Scope) 52 (References) 93 (Definitions) 94 / (Owner/User Inspection Organization) 185 (Inspection and Testing Practices) 21Doc. No.: TD-570A-03 Page 2 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 2 78 onor ervice HS5.3.6 (Erosion) / (corrosion/erosion) 275.3.7 Environmental cracking 285.3.8 (lining) 295.3.9 Fatigue cracking 305.3.10 Creep cracking 315.3.11 Brittle fracture () 325.3.12 Freeze damage 325.4 (Types of Inspection and Surveillance) 335.4.1 (Internal visual inspection) 335.4.2 (Thickness measurement inspection) 335.4.3 (External Visual Inspection) 345.4.4 (Vibrating piping inspection) 355.4.5 (Supplemental inspection) 365.5 (Thickness Measurement Locations TML) 365.5.1 (General) 365.5.2 TML (TML Monitoring) 365.5.3 TML (TML Selection) 375.6 (Thickness Measurement Methods) 395.7 (Pressure Testing of Piping Systems) 405.8 (Material Verification and Traceability) 425.9 (Inspection of Valves) 435.10 (Inspection of Welds In-Service) 445.11 (Inspection of Flanged Joints) 466.1 486.2 Piping Service Classes 496.2.1 Class 1 496.2.2 Class 2 506.2.3 Class 3 506.3 506.4 CUI 526 (Frequency and Extent of Inspection) 48Doc. No.: TD-570A-03 Page 3 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 3 78 onor ervice HS6.6.1 (Small bore piping, SBP) 546.5 546.6 (Small-bore) (Auxiliary piping) 546.6.2 (auxiliary piping) 556.6.3 (threaded connections) 557.1 (Corrosion Rate) 577.1.1 (Remaining Life) 577.1.2 587.1.3 587.2 (Maximum Allowable Working Pressure (MAWP) 597.3 597.4 607.5 Piping Stress Analysis 617.6 628.1.1 (Repair) (Alteration) 648.1.2 (Authorization) 648.1.3 (Approval) 648.1.4 ( ) 658.1.5 (Repair) () 668.2 Hot Tapping 678.2.1 (Procedure), (Qualification) (Record) 678.2.2 Preheat Postweld heat treatment 678.2.3 Design 698.2.4 698.2.5 (NDT) 708.2.6 Pressure Testing 707 (Inspection Data Evaluation, Analysis, and Recording) 578 (Repair, (Alteration) (Rerating) (Repairs, Alterations, and Rerating of Piping Systems) 64Doc. No.: TD-570A-03 Page 4 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 4 78 onor ervice HS8.3 (Rerating) 719.1 (Types and Methods of Inspection) 729 (Inspection of Buried Piping) 729.1.1 (Above-Grade Visual Surveillance) 729.1.2 (Close-Interval Potential Survey) 729.1.3 Coating Holiday (Pipe Coating Holiday Survey) 739.1.4 (Soil Resistivity) 739.1.5 Cathodic (Cathodic Protection Monitoring) 739.1.6 (Inspection Methods) 749.2 759.2.1 (Above-Grade Visual Surveillance) 759.2.2 (Pipe-to-Soil Potential Survey) 759.2.3 Coating Holiday (Pipe Coating Holiday Survey) 759.2.4 (Soil Corrosivity) 759.2.5 Cathodic (Cathodic Protection) 769.2.6 (External and Internal Inspection Intervals) 769.2.7 (Leak Testing Intervals) 779.3 779.3.1 Coating (Repairs to Coatings) 779.3.2 Clamp (Clamp Repairs) 789.3.3 (Welded Repairs) 789.4 78 Doc. No.: TD-570A-03 Page 5 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 5 78 onor ervice 1 1.1 HS (Scope) (General Application) 1.1.1 (Coverage) API 570 (Inspection) (Repair) (Alteration) (Rerating) (In-service) 1.1.2 API 570 API 570 (AIA - Authorized Inspection Agency) (Repair Organization) Piping Engineers, (Inspectors), (Examiners) 3 (Definitions) 1.1.3 API 570 (Original Construction) API 570 API 570 Doc. No.: TD-570A-03 Page 6 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 6 78 onor ervice 1.2 HS (Specific Applications) 1.2.1 API 570 ( 1.2.2) API 570 (Process Fluids) (Hydrocarbons) (Similar Flammable Toxic Fluid Service) a. , (Raw, intermediate, and finished petroleum products) b. , (Raw, intermediate, and finished chemical products) c. (Catalyst lines) d. (Hydrogen), (Natural Gas), (Fuel Gas), (Flare) e. (Sour Water) (Hazardous waste streams above threshold limits) f. (Hazardous chemicals above threshold limits) 1.2.2 API 570 API 570 API 570 / (Owner/User) API 570 1. (Hazardous fluid services below threshold limits waste) 2. () (Steam) (Steam Condensate) (Boiler Feed Water) Doc. No.: TD-570A-03 Page 7 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 7 78 onor ervice HS Category D ASME B31.3 API 570 1. (Truck) (Ship) (Barge) (Other mobile equipment) 2. (Rotating or Reciprocating mechanical device) Stress (Pump) (Compressor) (Turbine) (Generater) (Engine) (Hydraulic or Pneumatic) (Piping/Tubing) (Fired Heater) (B 3. oiler) Tube eader Tube H Return Bend sover External Cros 4. Manifold (Pressure Vessel) (Heater / Furnace) (Heat Exchanger) () 5. (Internal Piping) (Plumbing) Sewer) (Sanitary ess Waste Sewer) (ProcDoc. No.: TD-570A-03 Page 8 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 8 78 onor ervice 6. HS : OD NPS 7. (Nonmetallic Piping) (Polymer) ss-lined) 1.3 Fitnes (Glas-For-Service (FFS) ess-For-Service (FFS) API 570 Fitn API RP 579 API 570 Doc. No.: TD-570A-03 Page 9 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 9 78 onor ervice 2 HS (References) 3 Code API 570 (Definitions) API 570 3.1 alteration: (physical change) (Flexibility) alteration Branch (Reinforce) Branch (Reinforce) Branch (Reinforce) 3.2 applicable code: Code, Code, / (Owner/User) Piping Engineer ASME B31.3 3.3 ASME B31.3: ASME B31.3, Process Piping, ASME - American Society of Mechanical Engineers. ASME B31.3 ASME B31.3 , Rerating, Alteration Piping engineer Inspector API 570 ASME B31.3 Doc. No.: TD-570A-03 Page 10 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 10 78 onor ervice HS PWHT API 570 ASME B31.3 (principles of ASME B31.3) 3.4 ASME B31.3 (in accordance with ASME B31.3) authorized inspection agency: / (Owner/User) (Independent Inspection Organization) / (Owner/User) / (Owner/User) 3.5 auth (Independent Inspection Organization) / (Owner/User) orized piping inspector: ion agency API ized inspect570. author tor (nondestructive (NDE) examiner) authorized piping inspec 3.6 piping: Inspector API 570 authorized piping inspector auxiliary econdary process) (primary piping). (Instrument) (machinery) (s flush lines seal oil line analyzer line balance line Doc. No.: TD-570A-03 Page 11 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 11 78 onor ervice HS ine buffer gas l nt 3.7 i ves: drain vecrit cal check val 3.8 CUI: (Corrosion Under Insulation) on cracking stress corrosi3.9 deadlegs: blanked branches line block valves line pressurized dummy support legs ontrol valve bypass c (level bridles) relief valve (inlet) outlet) ( Line bypass Vent Drain le points) (samp (bleeders) 3.10 / (defect): 3.11 design temperature of a piping system component: Rating ode design temperature ASME B31.3 C esign temperatures d design temperature 3.12 (examiner): Doc. No.: TD-570A-03 Page 12 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 12 78 onor ervice HS r NDT API 570 ( / (Owner/User)) Inspecto Examiner Inspector API570 / (Owner/User) examiner / (Owner/User) SNT-TC-1A CP-189 ng Inspector certification AWS - Weldi aminer examiner inspector 3 ex 3.1 hold point: (Repair) (Alteration) 4 3.1 imperfections: 5 3.1 indication: t: 3.16 injection poin Injection point 2 Tee Injection point Chlorine in reformers water injection in overhead systems polysulfide injection in catalytic cracking wet gas antifoam injections inhibitors neutralizers 3.17 in-service: Doc. No.: TD-570A-03 Page 13 of 78 Revision: 0 API 570 (Piping Inspection Code) Issue Date: 10/6/2007 API 570 Piping Inspection () 13 78 onor e