-
5/21/2018 Datasheet DE450 PN10
1/8
TECHNICAL DATASHEETSegmented bend 30
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING CS3P450B
DN [mm] 450
SDR DESIGN 17
PN 10
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION PIPE
USE W
STANDARDS
DE [mm] 450 Z [mm] 360
H [mm] 300 S [mm] 26.7
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
-
5/21/2018 Datasheet DE450 PN10
2/8
TECHNICAL DATASHEETSegmented bend 45
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING CS4P450B
DN [mm] 450
SDR DESIGN 17
PN 10
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION PIPE
USE W
STANDARDS
DE [mm] 450 Z [mm] 514
H [mm] 300 S [mm] 26.7
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
-
5/21/2018 Datasheet DE450 PN10
3/8
TECHNICAL DATASHEETSegmented bend 90
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING CS9P450B
DN [mm] 450
SDR DESIGN 17
PN 10
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION PIPE
USE W
STANDARDS
DE [mm] 450 Z [mm] 867
H [mm] 300 S [mm] 26.7
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
-
5/21/2018 Datasheet DE450 PN10
4/8
TECHNICAL DATASHEETTee 90 long spigot
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING TP450B
DN [mm] 450
SDR DESIGN 17
PN/MOP 10/6.25
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION INJECTION MOULDED
USE W - GAS
STANDARDS UNI EN 12201-3
UNI EN 1555-3
UNI EN ISO 15494
DE [mm] 450 Z [mm] 984
H [mm] 195
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
-
5/21/2018 Datasheet DE450 PN10
5/8
TECHNICAL DATASHEETReduced tee 90 big diameter
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING TSHP450090B
DN [mm] 450x90
SDR DESIGN 17
PN/MOP 10/6.25
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION INJECTION MOULDED
USE W - GAS
STANDARDS UNI EN 12201-3
UNI EN 1555-3
UNI EN ISO 15494
DE [mm] 450 DE1 [mm] 90
Z [mm] 700 H [mm] 230
H1 [mm] 200
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
-
5/21/2018 Datasheet DE450 PN10
6/8
TECHNICAL DATASHEETReduced tee 90 big diameter
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING TSHP450110B
DN [mm] 450x110
SDR DESIGN 17
PN/MOP 10/6.25
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION INJECTION MOULDED
USE W - GAS
STANDARDS UNI EN 12201-3
UNI EN 1555-3
UNI EN ISO 15494
DE [mm] 450 DE1 [mm] 110
Z [mm] 700 H [mm] 230
H1 [mm] 200
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
-
5/21/2018 Datasheet DE450 PN10
7/8
TECHNICAL DATASHEETReduced tee 90 big diameter
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING TSHP450160B
DN [mm] 450x160
SDR DESIGN 17
PN/MOP 10/6.25
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION INJECTION MOULDED
USE W - GAS
STANDARDS UNI EN 12201-3
UNI EN 1555-3
UNI EN ISO 15494
DE [mm] 450 DE1 [mm] 160
Z [mm] 700 H [mm] 230
H1 [mm] 200
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
-
5/21/2018 Datasheet DE450 PN10
8/8
TECHNICAL DATASHEETReducer short spigot
IDENTIFICATION OF PRODUCT GEOMETRIC CHARATERISTICS
TYPE OF FITTING RCP450400B
DN [mm] 450x400
SDR DESIGN 17
PN 10
RAW MATERIAL PE 100
TRADEMARK PLAST
EXECUTION INJECTION MOULDED
USE W
STANDARDS UNI EN 12201-3
UNI EN ISO 15494
-
DE [mm] 450 DE1 [mm] 400
Z [mm] 188 H [mm] 64
H1 [mm] 99
WEIGHT [kg] -- VOLUME [m] --
SDR FUSION 17
MARKING CHARATERISTICS OF ELECTRIC CIRCUIT
TYPE OF CIRCUIT --
CONNECTOR DIAMETER [mm] --
VOLTAGE [V] --
RESISTANCE [Ohm]
PLASTITALIA SPA reserves the right to revise this specification,
while maintaining compliance with the requirements of the product
without prior
notice.Tolerance on diameters and thickness according to the
standards unless otherwise specified. Tolerance: 5%
18/06/2014
