Upload
anonymous-4mwmdanb
View
223
Download
0
Embed Size (px)
Citation preview
8/11/2019 fts20
1/36
D
E
F
KA00180F/00/A3/13.1171144409
SchwimmschalterFTS20
GrenzschalterPoint Level Switch
Dtecteur de niveau
8/11/2019 fts20
2/36
2 Endress+Hauser
D
SicherheitshinweiseDer Schwimmschalter FTS20 darf nur als Fllstandgrenzschalter in geeigneten Flssigkeiteneingesetzt werden. Bei unsachgemem Einsatz knnen Gefahren von ihm ausgehen.Das Gert darf nur von qualifiziertem und autorisiertem Personal unter besonderer Beachtung dieser Kompaktanleitung, der einschlgigen Normen, der gesetzlichen Vorschriften und der Zertifikate (je nach Ausfhrung und Anwendung)eingebaut, angeschlossen und in Betrieb genommen werden.
Sicherheitssymbole
# Warnung!Warnung deutet auf Aktivitten oder Vorgnge, die wenn sie nicht ordnungsgem durchgefhrtwerden zu Verletzungen von Personen oder zu einem Sicherheitsrisiko fhren knnen. BeachtenSie die Arbeitsanweisungen genau und gehen Sie mit Sorgfalt vor.
!Hinweis!Hinweis deutet auf Vorgnge, die wenn sie nicht ordnungsgem durchgefhrt werden einen Einfluss auf den Betrieb haben oder eine unvorhergesehene Gertereaktion auslsen knnen.
8/11/2019 fts20
3/36
Endress+Hauser 3
D
Gertevarianten
Bestellcode Kabellnge Schaltertyp
N
A
M
U
R
Initiator mit Schaltkugel fr den Einsatz im Ex-Bereich2-Leiter nach EN 60947-5-6 (NAMUR)Einsatz mit Trennverstrker; ATEX II 2 G EEx ia IIB T5
5201011971035516
5 m20 m
mit Kabelmaterial PVC (schwarz)
5201012071035517
5 m20 m
mit Kabelmaterial PUR (grau)
5201012171035518
5 m20 m
mit Kabelmaterial CSM (schwarz)
A
C /
D
C
Mikroschalter mit Schaltkugel fr den Standardeinsatz,3-Leiter, Wechsler fr max. 250 V AC / 150 V DC
5201012271035520
5 m20 m
mit Kabelmaterial PVC (schwarz)
52010123
71035521
5 m
20 m
mit Kabelmaterial PUR (grau)
5201012471035522
5 m20 m
mit Kabelmaterial CSM (schwarz)
8/11/2019 fts20
4/36
4 Endress+Hauser
D
Funktion
Ein im Schwimmschalter eingebautes Schaltelement schaltet bei Abweichung aus der Waagerechten.Der Schaltvorgang wird durch die Bewegung einer Stahlkugel ausgelst und je nach Ausfhrungdurch einen induktiven Initiator oder einen Mikroschalter ausgefhrt.Als Schaltausgang stellt der induktive Initiator ein Schaltsignal nach EN 60947-5-6 (NAMUR) zur Ver-fgung. Die Ausfhrung mit Mikroschalter einen Wechselkontakt.
Merkmale sichere Grenzwerterfassung von Fllstnden in Flssigkeiten elektrische Anschlsse nach NAMUR fr den Ex-Bereich (bis Zone 1) oder Wechsler (AC/DC)
fr den universellen Standardeinsatz verschiedene Kabelmaterialien fr unterschiedliche Medien kleiner Durchmesser fr einfache Montage durch Gewindebohrung G1A
Zubehr
Nivotester FTL325N Trennschaltverstrker52010125 Stopfbuchsverschraubung G1A, PVC52010126 Gegenmutter G1A, PVC52010127 Beschwerungsgewicht (Polyamid beschichtet)
8/11/2019 fts20
5/36
Endress+Hauser 5
D
AnwendungenPumpen und Ventile mit einem Schalter steuern oder Fllstandhhe bzw. -grenze signalisieren
8/11/2019 fts20
6/36
6 Endress+Hauser
D
EinbauDer Schwimmschalter kann wie folgt montiert werden: Der Schwimmschalter kann von auen durch eine Gewindebohrung G1A in den Behlter
eingefhrt und mit der Stopfbuchsverschraubung (G1A) verschraubt werden Bei Montage von oben sollte das Beschwerungsgewicht verwendet werden
! Hinweis! Der Drehpunkt des Kabels soll immer waagerecht liegen
Die Kabellnge zwischen Befestigung und Schwimmkrper ist abhngig vom Kabeltyp(siehe Technische Daten) Bei Verwendung des Beschwerungsgewichtes mu hinter der Stopfbuchsverschraubung
auf der Auenseite des Behlters eine zustzliche Zugentlastung (z.B. ein Knoten im Kabel)angebracht werden
8/11/2019 fts20
7/36
Endress+Hauser 7
D
Elektrischer Anschluss
# Warnung!Beachten Sie den Schaltertyp!
Initiator mit Schaltkugel(NAMUR)Bestellcodes:52010119, 5201012052010121, 7103551671035517, 71035518
AnschlusskennungL+ = Schwarz oder BraunL- = Blau(Schlieend beim Aufschwimmen)
Wechselkontakt(AC/DC)Bestellcodes:
52010122, 5201012352010124, 7103552071035521, 71035522
Kabelfarben:Schwarz + Braun = Kontakt geffnet
Schwarz + Blau = Kontakt geschlossen(Kontaktelage beim Aufschwimmen)
8/11/2019 fts20
8/36
8 Endress+Hauser
D
Technische Daten FTS20 (NAMUR)Messsystem Bestehend aus Schwimmschalter FTS20 und einem Trennschaltverstrker,
z.B. Endress+Hauser Nivotester FTL325N
Schaltelement Induktiver Nherungsschalter mit Schaltkugel, aufschwimmend schlieendHilfsenergie 8,2 V 2 VBetriebsstrom 2,1 mA geschaltetVerpolschutz JaSchaltwinkel Schaltpunkte oben/unten 12, gegen die Waagerechte gemessen
Prozesstemperaturbereich Abhngig vom Kabelmaterial: PVC und PUR: +5+70 C, CSM: -20+85 CSchutzart DIN EN 60529, IP68 (20 m untertauchen / zeitlich ohne Begrenzung)Prozessdruck 3 bar bei 20 CDichte Flssigkeit 0,8 g/cm3
Material Schwimmkrper Polypropylen (PP)Material Kabel PVC, CSM: Standardlngen 5 m und 20 m, Querschnitt 2 x 0,75 mm2
PUR: Standardlngen 5 m und 20 m, Querschnitt 2 x 0,50 mm 2Mindestkabellnge zwischenBefestigung und Schwimmkr-per
PVC: 50 mmPUR: 100 mmCSM: 100 mm
Ex-Zulassung TV 01 ATEX 1709
Ex-Schutzart0
II 2G EEx ia II B T5Ex-Daten T5 (Ta = 70 C) T4 (Ta = 70 C)Spannung U i 16 V 16 VStrom Ii 52 mA 72 mALeistung Pi 180 mW 242 mWInduktivitt Li 1 mH 1 mHKapazitt Ci 153 nF 153 nF
Normen EN 60947-5-2, EN 50014:1997, EN 50020:1994
8/11/2019 fts20
9/36
Endress+Hauser 9
D
Technische Daten FTS20 (AC/DC)Messsystem bestehend aus einem Schwimmschalter FTS20Schaltelement Mikroschalter mit SchaltkugelSchaltfunktion WechslerSchaltspannung AC: max. 250 V; DC: max. 150 VSchaltstrom max. 3 A (AC), max. 1 A (DC)Schaltwinkel oberer Schaltpunkt: + 25 6,
unterer Schaltpunkt: +14 3, gegen die Waagerechte gemessen
Prozesstemperaturbereich Abhngig vom Kabelmaterial: PVC und PUR: +5+70 C, CSM: -20+85 CSchutzart DIN EN 60529, IP68 (20 m untertauchen / zeitlich ohne Begrenzung)Prozessdruck 3 bar bei 20 CDichte Flssigkeit 0,8 g/cm3
Material Schwimmkrper Polypropylen (PP)
Material Kabel PVC, CSM: Standardlngen 5 m und 20 m, Querschnitt 3 x 0,75 mm2PUR: Standardlnge 5 m und 20 m, Querschnitt 3 x 0,50 mm 2
Mindestkabellnge zwischenBefestigung und Schwimmkr-per
PVC: 50 mmPUR: 100 mmCSM: 100 mm
8/11/2019 fts20
10/36
10 Endress+Hauser
D
Abmessungen
Schwimmschalter FTS20
Stopfbuchsverschraubung Beschwerungsgewicht
(Mae in mm)
135
2 9
, 2
G 1 A
SW 41
1 9 0
32,5
8/11/2019 fts20
11/36
Endress+Hauser 11
D
8/11/2019 fts20
12/36
12 Endress+Hauser
D
8/11/2019 fts20
13/36
E
KA00180F/00/EN/13.1171144409
Floating SwitchFTS20
GrenzschalterPoint Level Switch
Dtecteur de niveau
8/11/2019 fts20
14/36
2 Endress+Hauser
E
Safety instructionsThe FTS20 floating switch may only be used as a level limit switch in suitable liquids.Improper use may cause dangerous situations.The instrument may only be installed, connected and commissioned by qualified andauthorised personnel, paying particular attention to:
this compact manual the appropriate standards the statutory regulations and
certificates (depending on version and application)
Safety symbols
# Warning!Warning indicates an action or procedure which, if not performed correctly, can result ininjury or a safety hazard. Read the instructions thoroughly and proceed carefully.
! Note!"Note" indicates processes which if improperly executed could affect operation or triggerunexpected instrument actions.
8/11/2019 fts20
15/36
Endress+Hauser 3
E
Instrument variants
Order Code Cable length Type of switch
N
A
M
U
R
Initiator with switching ball for use in explosion-hazardous areas2-wire to EN 60947-5-6 (NAMUR)Use with isolating amplifier; ATEX II 2 G EEx ia IIB T5
5201011971035516
5 m20 m
With PVC cable material (black)
5201012071035517
5 m20 m
With PUR cable material (gray)
5201012171035518
5 m20 m
With CSM cable material (black)
A
C
/ D
C
Microswitch with switching ball for standard application,3-wire, change-over contact for max. 250 V AC / 150 V DC
5201012271035520
5 m20 m
With PVC cable material (black)
52010123
71035521
5 m
20 m
With PUR cable material (gray)
5201012471035522
5 m20 m
With CSM cable material (black)
8/11/2019 fts20
16/36
4 Endress+Hauser
E
Function
An element built into the floating switch switches when a deviation in the horizontal is detected.The switching process is triggered by the movement of a steel ball and, depending on the version,is carried out by an inductive initiator or a microswitch.The inductive initiator acts as a switching output and provides a switching signal to EN 60947-5-6(NAMUR). The microswitch version is a two-way switch.
Features Reliable level limit detection in liquids Electrical connections to NAMUR for hazardous areas (to Zone 1) or change-over contact
(AC/DC) for universal standard application
Different cable materials for different media Small diameter for simple installation using tapped hole G1A
Accessories
Nivotester FTL325N Isolating amplifier52010125 Compression gland G1A, PVC52010126 Counter nut G1A, PVC52010127 Weight (coated with polyamide)
8/11/2019 fts20
17/36
8/11/2019 fts20
18/36
6 Endress+Hauser
E
InstallationThe floating switch can be installed as follows: The floating switch can be inserted into the tank through a tapped hole G1A and screwed
to the compression gland (G1A). If it is installed from above, use the weight.
! Note! The fulcrum of the cable should always be horizontal.
The cable length between the fixture and the floating body is dependent on the cable type(see "Technical data"). When using the weight, place an extra strain relief (e.g. a knot in the cable) behind the
compression gland on the outside of the tank.
8/11/2019 fts20
19/36
Endress+Hauser 7
E
Electrical connection
# Warning!Note the switch type!
Inductive proximityswitch with switchingball (NAMUR)Order codes:52010119, 5201012052010121, 7103551671035517, 71035518
Connection indicationL+ = black or brownL- = blue
(closing when floating)
Change-over contact(AC/DC)Order codes:52010122, 5201012352010124, 7103552071035521, 71035522
Cable colours:black + brown = contact openblack + blue = contact closed(contact position when floating)
8/11/2019 fts20
20/36
8 Endress+Hauser
E
Technical data FTS20 (NAMUR)Measuring system Comprising an FTS20 floating switch and an isolating amplifier, e.g.
Endress+Hauser Nivotester FTL325N
Switching element Inductive proximity switch with switching ball, closed when floatingPower supply 8.2 V 2 VOperating current 2.1 mA switchedReverse polarity protection YesSwitching angle Switching points top/bottom 12, measured to the horizontal
Process temperature range Dependent on cable material:PVC and PUR: +5+70 C, CSM: 20+85 CIngress protection DIN EN 60529, IP68 (immension depth: 20 m / without temporal limit)Process pressure 3 bar at 20 CDensity of liquid 0.8 g/cm3
Floating body material Polypropylene (PP)Cable material PVC, CSM: standard length 5 m and 20 m , cross section 2 x 0.75 mm 2
PUR: standard length 5 m and 20 m , cross section 2 x 0.50 mm 2
Minimum cable length betweenfixing and floating body
PVC: 50 mmPUR: 100 mmCSM: 100 mm
Ex approval TV 01 ATEX 1709Ex ingress protection 0 II 2G EEx ia II B T5Ex data T5 (Ta = 70 C) T4 (Ta = 70 C)
Voltage Ci 16 V 16 VCurrent Ii 52 mA 72 mAPower Pi 180 mW 242 mWInductance Li 1 mH 1 mHCapacitance Ci 153 nF 153 nF
8/11/2019 fts20
21/36
Endress+Hauser 9
E
Technical data FTS20 (AC/DC)
Standards EN 60947-5-2, EN 50014:1997, EN 50020:1994
Measuring system Comprising an FTS20 floating switchSwitching element Microswitch with switching ballSwitching function Change-over contactSwitching voltage AC: max. 250 V; DC: max. 150 VSwitching current Max. 3 A (AC), max. 1 A (DC)Switching angle Upper switching point: +25 6
Lower switching point: +14 3, measured to the horizontalProcess temperature range Dependent on cable material:
PVC and PUR: +5+70 C, CSM: 20+85 CIngress protection DIN EN 60529, IP68 (immension depth: 20 m / without temporal limit)
Process pressure 3 bar at 20 CDensity of liquid 0.8 g/cm3
Floating body material Polypropylene (PP)Cable material PVC, CSM: standard length 5 m and 20 m , cross section 3 x 0.75 mm 2
PUR: standard length 5 m and 20 m , cross section 3 x 0.50 mm 2
Minimum cable length betweenfixing and floating body
PVC: 50 mmPUR: 100 mmCSM: 100 mm
8/11/2019 fts20
22/36
10 Endress+Hauser
E
Dimensions
FTS20 floating switch
Compression gland weight Weight
(Dimensions in mm)
135
2 9
, 2
G 1 A
SW 41
1 9 0
32,5
8/11/2019 fts20
23/36
Endress+Hauser 11
E
8/11/2019 fts20
24/36
12 Endress+Hauser
E
8/11/2019 fts20
25/36
F
KA00180F/00/FR/13.1171144409
Interrupteur flotteurFTS20
GrenzschalterPoint Level Switch
Dtecteur de niveau
8/11/2019 fts20
26/36
2 Endress+Hauser
F
Consignes de scuritL'interrupteur flotteur FTS20 doit uniquement tre mis en uvre en tant que dtecteur de niveau,dans des liquides appropris. Il peut en rsulter des dangers en cas d'utilisation inapproprie.L'appareil doit uniquement tre mont, raccord et mis en service par un personnel qualifi etautoris, en respectant tout particulirement cette instruction abrge, les normes en vigueur, les prescriptions lgales, et
les certificats (selon la version et l'application).
Symboles de scurit
# Avertissement !Le symbole Avertissement fait allusion des actions ou processus qui, s'ils ne sont pas excutsde faon conforme, peuvent entraner des blessures sur des personnes ou porter atteinte lascurit. Observez les instructions de travail de faon prcise, et procdez avec soin.
! Remarque !Le symbole Remarque fait allusion des processus qui, s'ils ne sont pas excuts de faonconforme, peuvent avoir une influence sur le fonctionnement ou dclencher une raction imprvisiblede l'appareil.
i d il
8/11/2019 fts20
27/36
Endress+Hauser 3
F
Variantes d'appareils
Numro de
commande
Longueur
par cbleType de interrupteur
N
A
M
U
R
Initiateur avec bille de commutation pour une mise en uvre en zone explosive2 conducteurs selon EN 60947-5-6 (NAMUR)Utlisation avec amplificateur-sparateur ; ATEX II 2 G EEx ia IIB T5
5201011971035516
5 m20 m
avec cble en PVC - polychlorure de vinyle (noir)
5201012071035517
5 m20 m
avec cble en PUR - polyurthane (gris)
5201012171035518
5 m20 m
avec cble en CSM - polythylne chlorosulfon (noir)
A
C /
D
C
Micro-interrupteur avec bille de commutation pour utilisation standard,3 conducteurs, inverseur pour max. 250 V c.a. / 150 V c.c.
5201012271035520
5 m20 m
avec cble en PVC polychlorure de vinyle (noir)
5201012371035521
5 m20 m
avec cble en PUR polyurthane (gris)
5201012471035522
5 m20 m
avec cble en CSM polythylne chlorosulfon (noir)
8/11/2019 fts20
28/36
4 Endress+Hauser
F
Principe de fonctionnement
Un lment de commutation intgr dans l'interrupteur flotteur commute en cas d'cart par rapport la position horizontale.Le processus de commutation est dclench par le mouvement d'une bille en acier et excut,suivant la version, par un initiateur inductif ou un micro-interrupteur.L'initiateur inductif met un signal de commande selon EN 60947-5-6 (NAMUR), en tant que sortie
tout ou rien. La version avec micro-interrupteur possde un contact inverseur.
Caractristiques Dtection sre de seuils de remplissage dans les liquides Connexions lectriques selon NAMUR pour la zone explosive (jusqu' la zone 1) ou inverseur
(AC/DC) pour une utilisation standard universelle Diffrents matriaux de cble pour diffrents fluides Petit diamtre pour montage simple travers un trou taraud G1A
Accessoires
Nivotester FTL325N Amplificateur-sparateur52010125 Raccord viss presse-toupe G1A, en PVC52010126 Contre-crou G1A, en PVC52010127 Lest (revtement en polyamide)
A li ti
8/11/2019 fts20
29/36
Endress+Hauser 5
F
ApplicationsCommande de pompes et vannes par interrupteur ou signalisation du niveau ou du seuil de remplissage
Montage
8/11/2019 fts20
30/36
6 Endress+Hauser
F
MontageL'interrupteur flotteur peut tre mont de la faon suivante : L'interrupteur flotteur peut tre insr dans un rservoir par l'extrieur, travers un trou
taraud G1A, et fix l'aide du raccord viss presse-toupe (G1A) Il convient d'utiliser le lest en cas de montage par le haut
! Remarque ! Le point d'articulation du cble doit toujours tre l'horizontale.
La longueur de cble entre la fixation et le flotteur dpend du type de cble(voir caractristiques techniques) En cas d'utilisation du lest, il convient de fixer un dispositif de dcharge supplmentaire
(p. ex. un noeud sur le cble) derrire le raccord viss presse-toupe, sur le ct extrieurdu rservoir
Raccordement lectrique
8/11/2019 fts20
31/36
Endress+Hauser 7
F
Raccordement lectrique
# Avertissement !Veillez au type d'interrupteur !
Dtecteur inductif deproximit avec bille decommutation (NAMUR)N darticle:
52010119, 5201012052010121, 7103551671035517, 71035518
Identification de raccordementL+ = noir ou brunL- = bleu( fermeture au flottage)
Inverseur (AC/DC)N darticle:52010122, 5201012352010124, 7103552071035521, 71035522
Couleurs des cbles :noir + brun = contact ouvert
noir + bleu = contact ferm(tat des contacts au flottage)
Caractristiques techniques FTS20 (NAMUR)
8/11/2019 fts20
32/36
8 Endress+Hauser
F
Caractristiques techniques FTS20 (NAMUR)
Systme de mesure Compos de l'interrupteur flotteur FTS20 et d'un amplificateur-sparateur, p. eEndress+Hauser Nivotester FTL325N
lment de commutation Dtecteur inductif de proximit avec bille de commutation, fermeture au flotAlimentation 8,2 V 2 VCourant de service 2,1 mA commutProtection contre l'inversion de polarit OuiAngle de commutation Points de commutation en haut / en bas 12, mesur par rapport l'horizontalTemprature du process dpendante du matriau du cble:
PVC et PUR: +5+70 C, CSM: 20+85 CDegr de protection DIN EN 60529, IP68 (immersion 20 m, pas de limitation de temps)Pression du process 3 bars 20 CDensit du fluide 0,8 g/cm3
Matriau du flotteur Polypropylne (PP)
Matriau du cble PVC, CSM: longueur standard 5 m et 20 m, section 2 x 0,75 mm2PUR: longueur standard 5 m et 20 m, section 2 x 0,50 mm2
Longueur minimale de cble entre lafixation et le flotteur
PVC : 50 mmPUR : 100 mmCSM : 100 mm
Agrment Ex TV 01 ATEX 1709Type de protection antidflagrante 0 II 2G EEx ia II B T5Donnes Ex T5 (Ta = 70 C) T4 (Ta = 70 C)
Tension Ui 16 V 16 VCourant Ii 52 mA 72 mAPuissance Pi 180 mW 242 mWInductance Li 1 mH 1 mHCapacit Ci 153 nF 153 nF
Normes EN 60947-5-2 EN 50014:1997 EN 50020:1994
8/11/2019 fts20
33/36
Endress+Hauser 9
F
Caractristiques techniques FTS20 (AC/DC)
Normes EN 60947 5 2, EN 50014:1997, EN 50020:1994
Systme de mesure compos d'un interrupteur flotteur FTS20lment de commutation Micro-interrupteur avec bille de commutationFonction de commutation inverseurTension de commutation AC : max. 250 V ; DC : max. 150 VCourant de commutation max. 3 A (AC), max. 1 A (DC)
Angle de commutation point de commutation suprieur : +25 6,point de commutation infrieur : +14 3, mesur par rapport l'horizontale
Temprature du process dpendante du matriau du cble:PVC et PUR: +5+70 C, CSM: 20+85 C
Degr de protection DIN EN 60529, IP68 (immersion 20 m, pas de limitation de temps)
Pression du process
3 bars 20 CDensit du fluide 0,8 g/cm3
Matriau du flotteur polypropylne (PP)Matriau du cble PVC, CSM: longueur standard 5 m et 20 m, section 3 x 0,75 mm2
PUR: longueur standard 5 m et 20 m, section 3 x 0,50 mm2
Longueur minimale de cble entrela fixation et le flotteur
PVC : 50 mmPUR : 100 mmCSM : 100 mm
Dimensions
8/11/2019 fts20
34/36
10 Endress+Hauser
F
Dimensions
Interrupteur flotteur FTS20
Raccord viss presse-toupe Lest
(Cotes en mm)
135
2 9
, 2
G 1 A
SW 41
1 9 0
32,5
8/11/2019 fts20
35/36
Endress+Hauser 11
F
L'attestation d'examen CE de type figure en langue anglaise aux pages 11 et 12.
8/11/2019 fts20
36/36