Upload
warman-fatra
View
219
Download
0
Embed Size (px)
Citation preview
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 1/17
Mechanical joining — Tensile shear testing of single joint specimens — Specimendimensions and test procedure
Assemblage mécanique — Essais quasi statiques de traction-cisaillement des échantillons à jonction unique —…
(de: Mechanisches Fügen — Scherzugprüfung von Einpunktproben — Probenmaße und Prüfung )
Parts of the draft shaded in ellow need further consideration.
Dokument-Typ: NormDokument-Untertyp:Dokumentstufe: EntwurfDokumentsprache: D
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 2/17
Contents Page
Foreword
Foreword .........................................................................................................................................................3
1 Scope..................................................................................................................................................4
2 Normative references........................................................................................................................4
3 Terms and definitions .......................................................................................................................4
4 Test specimens and types of tests..................................................................................................6
5 Test equipment and test procedure ................................................................................................7
6 Failure mode ......................................................................................................................................9
7 Test report ..........................................................................................................................................9 A.1 General .............................................................................................................................................10 A.2 Typical failure modes of semi-tubular self piercing rivet joints under shear load...................10
A.3 Typical failure modes of solid self piercing rivet joints ..............................................................11
A.4 Typical failure modes of clinch joints ...........................................................................................12 A.5 Typical failure modes of screwed joints .......................................................................................13 A.6 Typical failure modes of joints made with self clinching or self piercing nuts ........................14 A.7 Typical failure modes of joints made with self clinching or self piercing bolts .......................15 A.8 Typical failure modes of blind rivet joints ....................................................................................16 A.9 Typical failure modes of lock bolt joints.......................................................................................17 A.10 Slippage in a mechanical joint .......................................................................................................18
2
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 3/17
1 Scope
This standard specifies the geometry of the test specimens and the procedure for the tensile shear testing ofsingle mechanical joints on single and multi-layer specimens up to a single sheet thickness of 4,5 mm.
The term sheet, as used in this standard, includes extrusions and cast materials.
The purpose of the tensile shear test is to determine the mechanical characteristics and failure types of the joints made with the different methods.
2 Normative references
The following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenceddocument (including any amendments) applies.
ISO 2768-1, General tolerances — Tolerances for linear and angular dimensions without individual tolerance
indications
ISO 7500-1 Metallic materials — Verification of static uniaxial testing machines — Part 1:Tension/compression testing machines — Verification and calibration of the force-measuring system
3 Terms and definitions
For the purpose of this document, the following terms and definitions apply.
3.1tensile shear load
F max.
maximum load, recorded in the test
Note If required, further characteristic data, e.g. F p0,2 (see 3.2), stiffness of the specimen c (see 3.6) or slope of the
force curve γ, energy dissipation W (see 3.7), can be determined according to the shear diagram given in Figure 4.
3.2elastic load limitF p0,2
maximum load before plastic or permanent deformation of 0,2 % occurs
3.3displacement
s
increase in the length of the specimen during the tensile shear test
3.4
displacement at the maximum load F max
sFmax
amount of displacement measured at maximum load F max
3.5displacement at 0,3F max
s0,3Fmax
amount of displacement measured at 0,3F max
4
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 4/17
3.6stiffness in elastic range
c
ratio of increase of load to the increase of elongation in the elastic range (c = Δ F /Δ s)
3.7dissipated energy
W
work or area under the load curve
3.8dissipated energy up to F max W Fmax
area under the force curve up to the point of maximum tensile shear load F max
∫=
⋅=max
max
0
F
F
s
s
ds F W
3.9dissipated energy up to 0,3F max W 0,3Fmax area under the load curve up to the point where the tensile shear force drops to 30% of F max
∫=
⋅=
max3,0
max3,0
0
F
F
s
s
ds F W
3.10dissipated energy up to fracture
W fracture total area under the force curve
∫=
⋅= fracture s
s
fracture ds F W 0
3.11
displacement at maximum load F max sFmax
displacement at which the maximum load F max is recorded
3.12displacement at 0,3F max s0,3Fmax
displacement at which 0,3 F max is recorded
3.13form fit…(Dr. Singh)
3.14force fit…(Dr. Singh)
5
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 5/17
4 Test specimens and types of tests
Tolerances according to ISO 2768-1 are applicable to the dimensions of the specimens given in Table 1.
((Missing reference to Figures 1 and 2))
Keya overlapb coupon widthl c length of clamped areal s total length of specimen
l g specimen length between clampsl t coupon lengtht 1 , t 2 sheet thickness
1 shim plates
Figure 1 —Single-lap tensile shear test specimens
((2nd
specimen with indication of visual and blind side and reverse))
Key
1 shim plates
Figure 2 — Examples of different sheet testing arrangements for tensile shear test specimens
6
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 6/17
Stacking order of the sheets, the joining directions, the visible and blind side, etc. shall be agreed uponbetween the contracting parties.
Table 1 — Specimen dimensions
Thickness ofsheet
t 1; t 2
Overlap
a
Specimenwidth
b
Length ofclamped area
l c
Specimen lengthbetween clamps
l g
mm mm mm
≤ 4,5 5 × d 7 × d ≥ 45 95
NOTE Total specimen length: l s = l g + 2 l c, where the length of the clamped area is to be selected
in accordance with the testing machine being used.
d Shank diameter of blind rivets and self-locking collar bolts as well as nominal diameter of thread at
screws.
5 Test equipment and test procedure
The test specimen is clamped in a tensile testing machine according to ISO 7500-1, in such a manner, thatthe clamps are at the required distance from one another. For sheet thicknesses > 1 mm or where the ratio ofthe thicknesses is >1,4, shim plates shall be used for clamping the test specimen in the grips of the tensiletesting machine to ensure load concentricity (see Figure 3 b) and c)). Shim plates can be joined by suitable
joining method, e.g. resistance spot welding, adhesive bonding.
Testing shall be carried out at room temperature.
The speed of testing is 10 mm/min.
NOTE If tests at higher speeds show that the higher testing speed has no influence on the test results, then the higher
testing speed may be used for the tensile shear tests.
The elongation shall be measured as the displacement of the crosshead or by using extension callipergauges, laser measuring equipment or other suitable extension sensors with a defined length directly on thespecimen. Measurements made using signals from the crosshead should, if necessary, be corrected by takingthe stiffness of the machine into consideration. The sensing method used and the defined length of thespecimen measured shall be recorded in the test report.
Tests results are comparable only when the tests are carried out under identical boundary conditions.
7
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 7/17
a) Test arrangementwithout shim plates
b) Test arrangementwith shim plates (two
layers)
c) Test arrangement with shimplates (three layers)
Key
1 shim plates
Figure 3 — Set-up for tensile shear test specimens
Figure 4 illustrates a load elongation diagram for specimens with form and force fit joints. Correspondingdiagrams for force fit joints can exhibit slippage before the yield point. In addition different diagrams can be theresult of different combinations of joining methods, sheet materials and thicknesses, as well as specimengeometries.
F max
s Fmax
0,3Fmax
s 0,3 Fmax s Fracture
γ
F
F p 0,2
W
s
Key
F loads elongation
Figure 4— Characteristic values of a load-elongation diagram for the tensile shear test
8
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 8/17
6 Failure mode
The failure mode after tensile shear testing shall be classified according to Annex A.
7 Test report
The test report shall contain the following information:
a) name of the operator and/or the examining body;
b) designation of this standard (ISO 12996);
c) date and signature of the operator or the examining body;
d) joining technology;
e) joining parameters and joining equipment, fastener used;
f) specimen material and material condition;
g) specimen dimensions;
h) testing machine, test speed;
i) defined length on specimen and gauge type used for displacement measurements single values, meanvalues and standard deviation of the characteristic values;
j) individual test results, standard deviation, Coefficient of variation for the forces and the elongation
k) failure mode;
l) any additional remarks if required.
9
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 9/17
Annex A(normative)
Types of joint failure
A.1 General
Depending on the joining technology, different types of failure can occur. Some of these are specific to the joining technology employed and should be recorded in the test report. Typical failure modes for clinch, selfpiercing rivet and screwed joints are shown, by way of example, in Figures A.1 to A.8.
Criteria for a failure of a mechanical joint are to be agreed between contracting parties. Following figures givetypical failure modes at the end of the test.
A.2 Typical failure modes of semi-tubular self piercing rivet joints under shear load
a) Rivet pull out from bottom sheet
b) Pull out of rivet head
c) Failure of the specimen material
d) Rivet failure
Figure A.1 — Typical failure modes of semi-tubular self piercing rivet joints under shear load
10
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 10/17
A.3 Typical failure modes of solid self piercing rivet joints
a) Rivet pull out from bottom sheet
b) Pull out of rivet head
c) Failure of the specimen material
d) Rivet failure
Figure A.2 — Typical failure modes of solid self piercing rivet joints under shear load
11
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 11/17
A.4 Typical failure modes of clinch joints
a) Pull out
b) Neck fracture
c) Neck fracture with plastic deformation (mixed mode failure)
d) Pull out with neck fracture (mixed failure)
Figure A.3 — Typical failure modes of clinch joints
12
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 12/17
A.5 Typical failure modes of screwed joints
a) Thread in specimen stripped
b) Upper (head side) component fails
Figure A.4 — Typical failure modes of screwed joints (self drilling and thread forming screws)
13
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 13/17
A.6 Typical failure modes of joints made with self clinching or self piercing nuts
a) Impermissible specimen deformation or pull out of the nut
b) Specimen tear-out
c) Bolt failure
Figure A.5— Typical failure modes of joints made with self clinching or self piercing nuts
14
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 14/17
A.7 Typical failure modes of joints made with self clinching or self piercing bolts
a) Impermissible specimen deformation or pull out of the bolt
b) Specimen tear-out
c) Bolt failure
Figure A.6 — Typical failure modes of joints made with self clinching or self piercing bolts
15
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 15/17
A.8 Typical failure modes of blind rivet joints
a) Impermissible specimen deformation or rivet pull
b) Specimen tear out
c) Blind rivet failure
Figure A.7 — Typical failure modes of blind rivet joints
16
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 16/17
A.9 Typical failure modes of lock bolt joints
a) Impermissible specimen deformation or pull out of the bolt
b) Specimen tear out
c) Lock bolt failure
Figure A.8 — Typical failure modes of lock bolt joints
17
8/13/2019 ISO_TC_44___N_1757
http://slidepdf.com/reader/full/isotc44n1757 17/17
18
A.10 Slippage in a mechanical joint
Figure A.9 — Typical failure mode of slippage in a mechanical joint