st3500a

  • Upload
    jamesyu

  • View
    215

  • Download
    0

Embed Size (px)

Citation preview

  • 8/14/2019 st3500a

    1/3

    SEAGATE TECHNOLOGY, INC.Customer Technical Support FAX Network +1 408 438-8137

    Customer Technical Support Bulletin Boards (300-9600, 8-N-1)

    United States +1 408 438-8771 United Kingdom +44 628 478011

    Germany +49 89 140-9331 Singapore +65 227-2217

    (C)opyright 1991

    ST-3500A AT Interface

    J5 Drive ID Select and J6 (located on side Configuration Select Header near rear)

    o o o1

    +5v ---o o o40-pin I/O Cable Connector

    o o o o o1 1 2 3J1 :::::::::: ::::::::1 / \ o o o o o Remote LED 4Reserved

    0 0 0 0 Connection Jumper (pin 20 missing for 5 G G 12 (see below) Position keying purposes) DC Power

    J5

    1 o o-C o E o G-o o B-o o o o A D F H

    Defaults shown in solid lines

    J5 Jumper Funtion Description (* indicates default)

    A B (A=vertical, pins 9 & 10; B=horizontal, pins 8 & 10)OFF OFF Drive is the slave (Drive 1).OFF ON Drive is the master (Drive 0) with slave (Drive 1) present.ON* OFF Drive s the master (Drive 0).

    C (C=horizontal, pins 5 & 7)ON Slave (Drive 1) Present is connected to J1 pin 39. Jumpers

    "D" or "E" cannot be installed if jumper "C" is installed.

    D (D=vertical, pins 5 & 6)

    ON* DASP- is connected to J1 pin 39. Jumpers "C", "D", "F", or"G" cannot be installed if jumper "E" is installed.

    OFF REFSIG is not connected to J1 pin 39.

    E (E=horizontal, pins 3 & 5)ON REFSIG is connected to J1 pin 39. Jumpers "C", "D", "F",

    or "G" cannot be installed if jumper "E" is installed.

    OFF REFSIG is not connected to J1 pin 39.

  • 8/14/2019 st3500a

    2/3

    F (F=vertical, pins 3 & 4)ON* No external reference for REFSIG. Jumpers "E", "G", or "H"

    cannot be installed if jumper "F" is installed.

    OFF This location provides a port for external connection ofthe synchronized spindle reference signal (pin 3) andground (pin 4).

    G (G=horizontal, pins 1 & 3)ON REFSIG is connected to J1 pin 28. Jumpers "E" or "F" cannot

    be installed if jumper "G" is installed.

    OFF REFSIG is not connected to J1 pin 28.

    H (H=vertical, pins 1 & 2)ON Drive implements "CSEL" (Cable Select line in I/O connector)

    feature. Implementation not defined yet. Jumpers A and Bnot used if jumper H is on. (This jumper is mutuallyexclusive with jumper "G").

    OFF* Drive select is based on use of jumper A or B.

    J6 Jumper Funtion Description (2x3 jumper block)-------------------------------------------------

    1 Remote LED connection. Pin 6 is connected to +5v through a147 ohm resistor. Pin 5 is the LED driver.

    2 Reserved jumper position.

    3 Reserved jumper position.

    ST-3500A

    UNFORMATTED CAPACITY (MB) ________________502FORMATTED CAPACITY (xx SECTORS) (MB) _____426ACTUATOR TYPE ____________________________VOICE COILTRACKS ___________________________________10,829CYLINDERS __PHYSICAL______________________1,547 (user)HEADS ______PHYSICAL______________________7DISCS (3.5 in) ___________________________4MEDIA TYPE _______________________________THIN FILMRECORDING METHOD _________________________ZBR RLL (1,7)TRANSFER RATE INTERNAL (mbits/sec)________21.6 to 36SPINDLE SPEED (RPM) ______________________4,535AVERAGE LATENCY (mSEC) ___________________6.61

    BUFFER ___________________________________256 KByte SeaCachePrefetch, Multi-SegmentedINTERFACE ________________________________AT BUSSECTORS PER DRIVE ________________________TPI (TRACKS PER INCH) ____________________2150AVERAGE ACCESS (ms) (read/write)__________9.9/10.6SINGLE TRACK SEEK (ms) ___________________2MAX FULL SEEK (ms) _______________________21.5MTBF (power-on hours) ____________________200,000POWER REQUIREMENTS: +12V START-UP (amps) _1.5

    +12V TYPICAL (amps) __0.4

  • 8/14/2019 st3500a

    3/3

    +5V TYPICAL (amps) ___0.2TYPICAL (watts) ______5

    WRITE PRECOMP (cyl) ______________________N/AREDUCED WRITE CURRENT (cyl) ______________N/ALANDING ZONE (cyl) _______________________AUTO PARKIBM AT DRIVE TYPE ________________________*

    Physical:

    Height (inches/mm): 1.00/25.4Width (inches/mm): 4.00/101.6Depth (inches/mm): 5.75/146.1Weight (lbs/kg): 1.8/0.80

    * MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE. ALSO, CHECK TOSEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPEAVAILABLE. (see below)

    Possible translation: 895 cyl, 15 heads, 62 sectors = 426,163,200

    Note: A "custom" or "user-definded" CMOS drivetype may ask for anumerical value for the Write Precompensation cylinder and for the

    Landing Zone cylinder. A basic rule-of-thumb for drive models that donot require the old Write Precomp technique or a Landing Zone becausethey are Auto-Parking is to add 1 to the cylinder value being used. Asan example: If cylinders equaled 820, then both Write Precomp andLanding Zone would be entered as 821. Some BIOS will convert this to65535 or -1, which are functionally equivalent to "none (not used)".

    PHYSICAL/LOGICAL equivalent to NATIVE/TRANSLATION

    Already low-level formatted at the factory.

    Since a User-definable or Custom translation geometry may be used, itis imperative that the values be written down and kept with your

    permanent records for retrieval in the event of CMOS battery failure.

    Seagate reserves the right to change, without notice, productofferings or specifications. (10/12/92)#