108
Glossary (danh sách, các từ chuyên môn) BSC Base Station Controller CF Central Functions-nhiệm vụ chính, chức năng trung tâm CON LAPD Concentrator-tập trung DP Digital Path IS Interface Switch MO Managed Object RX Receiver TF Timing Function(chức năng định thời) TG Transceiver Group TRXC Transceiver Controller TS Time Slot Handler-bộ điều khiển khe thời gian TX Transmitter-máy phát pooltraf The number of transcoder resources currently used in traffic per pool. DCP=dcp Digital connection point number-số điểm kết nối số DCP1=dcp1 Digital Connection Point (DCP) number used for the signalling path to the TRXC Numeral 0 - 511 DCP2=dcp2 DCP number used for the speech and data connections to the TRXC Two DCP2s, for TRXCs using 16 Kbps Abis paths, or eight DCP2s, for TRXCs using 64 Kbps Abis paths, must be given. The DCP2s given must be consecutive(liên tục). The DCP2s are sorted into ascending order. If two DCP2s are given, the lower range DCP2 value is

Tong Hop Lenh Ericsson

Embed Size (px)

Citation preview

Page 1: Tong Hop Lenh Ericsson

Glossary (danh sách, các từ chuyên môn)

BSC Base Station ControllerCF Central Functions-nhiệm vụ chính, chức năng trung tâmCON LAPD Concentrator-tập trungDP Digital PathIS Interface SwitchMO Managed ObjectRX ReceiverTF Timing Function(chức năng định thời)TG Transceiver GroupTRXC Transceiver ControllerTS Time Slot Handler-bộ điều khiển khe thời gianTX Transmitter-máy phát

pooltraf The number of transcoder resources currently used in traffic per pool.

DCP=dcp Digital connection point number-số điểm kết nối sốDCP1=dcp1 Digital Connection Point (DCP) number used for the

signalling path to the TRXCNumeral 0 - 511

DCP2=dcp2 DCP number used for the speech and data connections to the TRXC

Two DCP2s, for TRXCs using 16 Kbps Abis paths, or eight DCP2s, for TRXCs using 64 Kbps Abis paths, must be given. The DCP2s given must be consecutive(liên tục). The DCP2s are sorted into ascending order. If two DCP2s are given, the lower range DCP2 value is associated(kết hợp) with TSs 0 to 3, and the higher range DCP2 is associated with TSs 4 to 7. If eight DCP2s are given, the lower range DCP2 value is associated with TS 0 and the higher range DCP2 value is associated with TS 7.Numeral 0 - 511

SIG=sig Signalling type UNCONC UnconcentratedCONC LAPD ConcentrationMPLEX16

Page 2: Tong Hop Lenh Ericsson

16K MultiplexMPLEX32 32K Multiplex

TEI Terminal Endpoint Identifier(nhận dạng)OML Operation and Maintenance(bảo dưỡng) LinkRXD

RECEIVER DIVERSITY-độ nhạy thu

BCCH Broadcast Control Channel-kênh điều khiển quảng bá

DCHNO=dchno(TCH) Absolute radio frequency channel number(đúng,chính xác) Maximum 32 Absolute Radio Frequency Channel Number (ARFCNs) per channel group are allowed. (31 if channel group 0).Numeral 128 - 251 (GSM 800) Numeral 1 - 124 (GSM 900, P-band) Numeral 0, 975 - 1023 (GSM 900, G1-band) Numeral 512 - 810 (GSM 1900) Numeral 512 - 885 (GSM 1800)

HOP=hop Frequency hopping status OFF The hopping status for the channel group is non-hopping. ON The hopping status for the channel group is hopping for Traffic Channel (TCH) and Stand-alone Dedicated Control Channel (SDCCH).

HSN=hsn Hopping sequence numberNumeral 0 - 63

CBCH=cbch Cell broadcast channel This parameter indicates if Cell Broadcast Channel (CBCH) is included in the Stand Alone Dedicated Control Channel (SDCCH).YES CBCH will be included in one of the SDCCH/8 for a cell or a channel groupNO No SDCCH/8 for a cell or a channel group will include CBCH

Page 3: Tong Hop Lenh Ericsson

CELL=cell Cell designation This is a symbolic name of a defined cell.

CHGR=chgr Channel group numberNumeral 0 - 15

SDCCH=sdcch Required number of SDCCH/8Numeral 0 - 32 (with combined BCCH 31)

TN=tn Timeslot numberNumeral 0 - 7

cgi Cell global identification-ô nhận dạng toàn cầu(khu vực) Expressed as(biểu diễn,trình bày) mcc-mnc-lac-ci where:mcc Mobile country codemnc Mobile network codelac Location area codeci Cell identity-ô nhận dạng

BCCHNO=bcchno Absolute radio frequency channel number for Broadcast Control Channel (BCCH) Absolute Radio Frequency Channel Number (ARFCN) already defined for a dedicated channel cannot be given.Numeral 128 - 251 (GSM 800) Numeral 1 - 124 (GSM 900, P-band) Numeral 975 - 1023, 0 (GSM 900, G1-band) Numeral 512 - 885 (GSM 1800) Numeral 512 - 810 (GSM 1900)

BCCHTYPE=bcchtype BCCH type This parameter indicates the combinatons of wanted logical channels on the frequency and timeslot defined for the BCCH in the cell.COMB Combined control channelIndicates that the cell has a combined BCCH and Stand Alone Dedicated Control Channel (SDCCH)/4.COMBC Combined control channel with a Cell Broadcast

Page 4: Tong Hop Lenh Ericsson

Channel (CBCH) subchannel Indicates that the cell has a combined BCCH and SDCCH/4 with a CBCH subchannel.NCOMB Non-combined control channelIndicates that the cell does not have any type of combined BCCH and SDCCH/4.This parameter applies only to internal cells

RLCRP:CELL=… 64k 64kbit/s Mode Supported CS3CS4

The Basic Physical Channel (BPC) supports General Packet Radio Service (GPRS) CS-3 or CS-4

EGPRS The BPC supports Enhanced(làm tăng, nâng cao) General Packet Radio Service (EGPRS)

NONE The BPC does not support EGPRS or GPRS CS-3 or CS-4

bcch Broadcast Control Channels (BCCHs) This parameter indicates the number of deblocked BCCHs in the cell.

bpc Basic Physical Channel individual

This individual is also printed in the RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT CONFIGURATION DATA printout, thus linking the configured logical channels with the Base Transceiver Station (BTS) equipment used for them.

cbch Cell Broadcast Channels (CBCHs) This parameter indicates the number of deblocked CBCHs in the cell.

cell Cell designation This is a symbolic name of a defined cell.

channel

Logical channel identity

This parameter consists of the channel type and an individual number.

chband Channel band This parameter indicates the frequency band for the logical channel.The channel band is printed for deblocked channels.800

GSM 800The BPC holding the channel is configured on one or several Absolute Radio Frequency Numbers (ARFCN) within the GSM 800 band in the range 128 - 251.

1800

Page 5: Tong Hop Lenh Ericsson

GSM 1800The BPC holding the channel is configured on one or several ARFCNs within the GSM 1800 band in the range 512- 885.

1900 GSM 1900The BPC holding the channel is configured on one or several ARFCNs within the GSM 1900 band in the range 512- 810.

P900 Primary GSM 900The BPC holding the channel is configured on one or several ARFCNs exclusively within the primary GSM 900 band in the range 1 - 124.

E900 Extended GSM 900The BPC holding the channel is configured on at least one ARFCN in the extended 'G1' GSM 900 band in the range 0, 975 - 1023.

chgr Channel group numberchrate Channel rate

FR Full rate

HR Half rate

chtype Channel type BCCH

Broadcast Control ChannelCBCH

Cell Broadcast ChannelSDCCH

Stand Alone Dedicated Control ChannelTCH

Traffic Channelicmband

Current idle channel interference band The interference is measured on an idle channel and the value range,from negativeto positive infinity (dBm), is divided into 5 intervals which are called idle channel interference bands. Interference band 1 is the band with the lowest interference. Interference band 5 is the band with the highest interference. An idle or busy SDCCH or TCH belongs to one of the idle channel interference bands.

Numeral 1 - 5noofch Number of deblocked logical channels

A logical channel in state idle, busy or locked is regarded as a deblocked channel.

nooftch

Number of traffic channels This number can have a lower and an upper limit. This is because there are BPCs

Page 6: Tong Hop Lenh Ericsson

configured with the possibility to be allocated either as full rate traffic channels (then counted as one channel) or half rate traffic channels (then counted as two channels). These channels are called dual rate channels. In a channel group or a cell, dual rate channels can be mixed with those of a fixed channel rate.

sdcch Stand Alone Dedicated Control Channel (SDCCH) This parameter indicates the number of deblocked SDCCHs in the cell.

spv Speech version If a traffic channel is configured with the possibility to be allocated for either of several speech versions, this parameter shows all the possible speech versions (for example spv = 1,2).

state Logical channel state BLOC

BlockedBUSY

BusyIDLE

IdleLOCK

LockedIf a BPC is configured with the possibility to be allocated either as a full rate traffic channel or two half rate traffic channels, the channel state LOCK is applicable. When one channel rate is allocated to a BPC, the logical channel or channels of the other rate on the same BPC are locked.

NONE No data existed to be printed.

EOT DURING PRINTOUT The operator has cancelled the printout.

FAULT INTERRUPTfault type

A fault interruption occurred during printing.

Fault type:

FORMAT ERRORThe command was incorrectly specified.

UNREASONABLE VALUE

details A parameter was specified with an unreasonable value.

FAULT CODE 3CELL NOT DEFINEDdetails

Page 7: Tong Hop Lenh Ericsson

The cell is not defined. FAULT CODE 19CELL RESOURCES HAVE CHANGED

Cell Resources have changed since printout started.

FAULT CODE 27CELL DATA CHANGE IN PROGRESS

Modification of cell data by a command is in progress.

FAULT CODE 38COMMAND NOT VALID FOR EXTERNAL CELLSdetails

The command is not valid for external cells. FAULT CODE 120CELL STATE NOT ACTIVEdetails

The cell has not been activated.

BA-list BCCH Allocation list

1.rxtcp:cell=hni,moty=rxotg; xem TG của trạm Parameters: thông số, tham số, tham biết, giới hạn Associated: kết hợp, liên kết dedicated to: có tính chất chuyên môn represented by: trình bày bởi, biểu diễn bởi

2.dtdii:dip=…,snt=…,dipp=…; Initiate: bắt đầu, khởi đầu, đề xướng Sequence: trình tự, kết nối

3.ntcop:snt=all; xem luồng thừa hay thiếu

SNT=snt Switching network terminal

DIPINF Digital path information related to the Switching Network Terminal (SNT)

ALL All switching network terminals

SNTP=sntp

Switching network terminal connection point

4.rlcrp:cell=hni; lệnh kiểm tra thuê bao chiếm kênh - CBCH: Cell Broadcast Channel-kênh quảng bá

Page 8: Tong Hop Lenh Ericsson

- NOOFTCH: Number of traffic channels This number can have a lower and an upper limit. This is because there are BPCs configured with the possibility to be(có khả năng,có thể) allocated(phân phối,cấp phát,định rõ vị trí) either as(chọn 1 trong hai vấn đề) full rate traffic channels (then counted as one channel) or half rate traffic channels (then counted as two channels). These channels are called dual(hai, đôi) rate channels. In a channel group or a cell, dual rate channels can be mixed(lẫn lộn,pha trộn,hỗn hợp) withthose of a fixed(đứng yên,cố định) channel rate.

icmband Current idle channel interference band The interference is measured on an idle channel and the value range,from negativeto positive infinity (dBm), is divided into 5 intervals which are called idle channel interference bands. Interference band 1 is the band with the lowest interference. Interference band 5 is the band with the highest interference. An idle or busy SDCCH or TCH belongs to one of the idle channel interference bands.

BPC Basic Physical Channel

5.rxcdp:mo=rxotg-tg; xem cấu hình của trạm - arfcn:Absolute Radio Frequency Channel Number: số kênh tần số radio chuẩn-txad:TX logical address.

Numeric value in the range 0 to 31

C0f Carrier zero filling(làm đầy,phủ đầy) YES

Carrier zero filling is turned on.NO

Carrier zero filling is turned off.

6. rxmfp:mo=rxots-TG-TRX-TS 0&&-TS7; xem số cuộc gọi trên ts.

conerrcnt Counter for the number of abnormally(khác thường) terminated connections

Page 9: Tong Hop Lenh Ericsson

concnt Counter for the number of connection setup attempts(cố gắng để làm gì)

7. Hạ cấu hình:-dtstp:dip=mã trạm;(xem trạm nằm ở BSC nào)-rxtcp:moty=rxotg,cell=mã trạm1;(xem TG) (rxmfp:mo=rxotg-TG;)-rxmsp:mo=rxotg-TG,subord;(xem cấu hình của trạm) -rxbli:mo=rxotrx-TG-TRX,subord,force;;(lệnh blok TRX)-rxese:mo=rxotrx-TG-TRX,subord;;(lệnh xóa TRX)

rxmoe:mo=RXOTX-125-6 ; rxmoe:mo=RXOTS-125-6-0 ; rxmoe:mo=RXOTS-125-6-1 ; rxmoe:mo=RXOTS-125-6-2 ; rxmoe:mo=RXOTS-125-6-3 ; rxmoe:mo=RXOTS-125-6-4 ; rxmoe:mo=RXOTS-125-6-5 ; rxmoe:mo=RXOTS-125-6-6 ; rxmoe:mo=RXOTS-125-6-7 ; rxmoe:mo=RXORX-125-6 ; rxmoe:mo=RXOTRX-125-6 ;

(rxcdp:mo=rxotg-TG;) +execute: thực hiện,thực hiện chỉ dẫn của máy tính,hành hình, hành quyết.

-rxmsp:mo=rxotg-TG,subord;(xem cấu hình của trạm) FORCE Forced blocking indication(sự chỉ dẫn)

SUBORD

Subordinate MOs (dưới quyền)All of the MO instances subordinate to the specified MO are included. Parameter SUBORD may be used for a Transceiver Group (TG) or Transceiver Controller (TRXC) in Base Transceiver Station (BTS) logical model G01 and TG, Central Function (CF) or TRXC in the BTS logical model G12.

8.Tích hợp trạm:-rlcfp:cell=mã trạm;(xem SDCCH,nhảy tần)-rldep:cell= mã trạm;(xem CGI)-dtqup:dip= mã trạm;(lệnh xem hệ số trượt của bit)-rxmop:mo=rxotg-tg;(lấy version)Khai mới:

Page 10: Tong Hop Lenh Ericsson

-ntcop:snt=etm...;-dtdii:dip=mã trạm,snt=emt...,dipp=...;;-dtbli:dip=mã trạm;;-dtble:dip=mã trạm;;-dtstp:dip=mã trạm;(xem luồng có hay chưa)Xem tọa độ luồng tại BSC:-dtdip:dip=ten tram;

Đổi tên dip(khi đã khai luồng nhưng bị nhầm và khi đã có dip)-dtpnc:dip=mã trạm mới,newdip=...,-dtble:dip=mã trạm;-dtstp:dip=mã trạm; Xóa dip:-dtbli:dip=mã trạm;;-dtdie:dip=mã trạm;;Khai inner( bên trong, nội bộ ) cell:

----- Khai bao cell tren MSC-----mgcei:cell=Mã trạm1,CGI= mcc-mnc-lac-ci1,BSC=BHNI…;mgcei:cell=Mã trạm2,CGI= mcc-mnc-lac-ci2,BSC=BHNI…;mgcei:cell=Mã trạm3,CGI= mcc-mnc-lac-ci3,BSC=BHNI…;

a, Parameters

BSC=bsc Base Station Controller (BSC) name

The BSC to which the cell is connected.

See Application Information for block MTRAN.CELL=cell Cell name

See Application Information for block MTRAN.CGI=cgi Cell Global Identity (CGI)

See Application Information for block MBSSD.

b, Function

This command initiates a new mobile telephony cell in the Mobile Services Switching Centre and Visitor Location Register (MSC/VLR) Server. The new cell is connected to a Base Station Controller.When the first cell is defined in location area, it defines the location area as well.

Page 11: Tong Hop Lenh Ericsson

The order remains after system restart.

Chú ý: mgcep:cell=mã trạm bất kỳ nào đó1;(lệnh in ra)Chú ý: lệnh xóa CGI trên MSC: phải print c á c cell n à y tr ê n BSC xem cell n à y c ò n tồn tại kh ô ng sau đ ó mới thực hiện c ô ng việc xo á :

mgcee:cell=mã trạm cell1;mgcee:cell=mã trạm cell2;mgcee:cell=mã trạm cell3;

Khai GPRS:rlgsi:cell=mã trạm...;(khai cả 3 cell) Khai outer( bên ngoài ) cell(nếu cdd yêu cầu giữa c á c MSC): mgoci:cell=HTY3156,cgi=452-04-12121-21926,msc=MHN2;

Các lỗi có thể trong CG:Khai bao INTERNAL:+ BSIC: phải là hai chữ số(ví dụ: 8=08)Khai bao TCH cho cell(xem thật kỹ)+rlcfi:cell=NDH3064,CHGR=1,DCHNO=768&771&774&777&780&783&786&789&792&795&798&801&804&807;+rlcfi:cell=NDH3065,CHGR=1,DCHNO=769&772&775&778&781&784&787&790&793&796&799&802&805&808;+rlcfi:cell=NDH3066,CHGR=1,DCHNO=770&773&776&779&782&785&788&791&794&797&800&803&806&809; +relation.Thong tin tram moi:Xem version(thay đổi version):+ RXMOI:MO=RXOTG-tg,TRACO=POOL,COMB=HYB,RSITE=mã trạm,SWVER=B4402R011L;Xem mã cell:+ RXMOC:MO=RXOTRX-tg-trx0, CELL=mã trạm...;(đối với trạm 1800 số cell được đánh là cell4,cell5,cell6).CHÚ Ý:Khai bao POWERCONTROL(chú ý phiên bản phần mềm)Khai bao Power UL(chú ý phiên bản phần mềm)Khởi tạo dev:

BLODI:DEV=RBLT……;

Page 12: Tong Hop Lenh Ericsson

(LÖnh nµy ®îc sö dông ®Ó deblock device sÏ chuyÓn tõ tr¹ng Idle th¸i

thµnh tr¹ng th¸i ABL(Automatic Block))EXDAE:DEV=RBLT……;

(LÖnh nµy ®îc sö dông ®Ó ®a c¸c Time Slot (t¬ng ®¬ng thuËt ng÷ Device) chuyÓn tõ tr¹ng th¸i In Service thµnh tr¹ng th¸i pre-post

service)

EXDAI:DEV=RBLT…;(LÖnh nµy ®îc sö dông ®Ó ®a c¸c Time Slot (t¬ng ®¬ng thuËt ng÷ Device) chuyÓn tõ tr¹ng th¸i pre-post

service thµnh tr¹ng th¸i In Service)

BLODE:DEV=RBLT…;(LÖnh nµy ®îc sö dông ®Ó deblock device

sÏ chuyÓn tõ tr¹ng th¸i ABL(Automatic Block) thµnh tr¹ng th¸i Idle)

Chạy lệnh và Dừng lại để kiểm tra:+ Khởi tạo Abis: RXAPI:MO=RXOTG-tg,DEV=RBLT2-513&&-543,DCP=1&&31;(LÖnh nµy ®îc sö dông ®Ó ®Þnh nghÜa mét hoÆc nhiÒu Abis paths gi÷a mét BSC vµ mét BTS. RBLT lµ device (TS) kÕt nèi tõ BSC tíi BTS.

DCP lµ sè nhËn d¹ng device ®ã.) + Lệnh active cell.+ §a c¸c MO sang tr¹ng th¸i In- Service RXESI:MO=RXOTG-28,SUBORD;(chờ full cảnh báo về)LÖnh nµy ®îc sö dông ®Ó ®a MO (bao gåm TG, CF, CON, TF, TRX, TX, RX, TS) vµo dÞch vô. Cã tíi 32 MO cã thÓ ®Þnh nghÜa trong mét lÖnh. Nhê sö dông th«ng sè SUBORD mµ ta chØ dïng 1 lÖnh mµ cã thÓ t¸c ®éng ®Õn tÊt c¶ c¸c MO con cña TG-nh vÝ dô trªn.+ Deblock các MO: RXBLE:MO=RXOTG-28,SUBORD;LÖnh nµy ®îc sö dông ®Ó deblock MO.RLSTC: CELL=HNIPDL1,STATE=ACTIVE;RLSTC: CELL=HNIPDL2,STATE=ACTIVE;RLSTC: CELL=HNIPDL3,STATE=ACTIVE;LÖnh nµy ®îc sö dông ®Ó thay ®æi tr¹ng th¸i cña Cell hoÆc CHGR. Cã c¸c tr¹ng th¸i lµ ACTIVE hoÆc HALTED.C hú ý: nếu TÍCH HỢP bị hiện tượng local mode có thể do các nguyên nhân sau: -khai sai TEI(có thể do cả BSC và BTS)

Page 13: Tong Hop Lenh Ericsson

-trong lúc tích hợp mất kết nối hoặc do DXU có vấn đề -chưa active dịch vụ(EXDAI, BLODE, RXAPI…) -do dưới trạm BTS chưa chuyển sang chế độ remove+, nếu do BSC sai do khai TEI thì cách chữa lại như sau: -rxbli:mo=rxotg-tg,subord,force; -rxese:mo=rxotg-tg,subord; -rxmoc:mo=rxotg-tg,tei=62(thêm nếu đổi sang Con hoặc Uncon); -rxesi:mo=rxotg-tg,subord; -rxble:mo=rxotg-tg,subord; 9.Thay đổi tham số handover:-RLIHC:CELL=cell…,iho=…;-RLIHC:CELL=cell…, SSOFFSETULP=giá trị dương, SSOFFSETULN=gía trị âm, QOFFSETULP=giá trị dương, QOFFSETULN=gía trị âm, SSOFFSETDLP= gía trị dương, SSOFFSETDLP= gía trị âm, MAXIHO=…, TMAXIHO=…, TIHO=…,-RLLUC:CELL=cell…, QLIMUL=…;

10.Thay đổi lac:-RLSTC:CELL=…,STATE=HALTED;-rldep:cell=…,cgi= mcc-mnc-lac-ci;-rldec:cell=…,cgi= mcc-mnc-lac-ci;-rlsbc:cell=…,t3212=…;mcc

Mobile country code Numeral 3 digits

mnc Mobile network code For the number of digits see the Application Information for block ROEPC.

lac Location area codeNumeral 1 - 65535

ci Cell identityNumeral 0 - 65535

CHÚ Ý:-Xem số lượng thuê bao(mgsvp;) ở MSC trước và sau khi thay đổi LAC(ghi lại giờ-số thuê bao)-phải giảm T3212 theo yêu cầu của CDD trước khi thay-Nếu không có LAI ở MSC khi thay đổi LAC thì dùng lệnh để khai: MGLAI:LAI=…-…-…;-khai inner cell và outer theo yêu cầu của CDD

Page 14: Tong Hop Lenh Ericsson

(mgbsp:bsc=all; xem tên BSC)-(mgnmp:msc=all; xem tên MSC)

11.Thay đổi con-uncon: khi đã nâng cấp rồi( không cần thiết ) Nếu là dùng con:

-rxmop:mo=rxocon-tg;(xem con)-rxmoc:mo=rxocon-tg,dcp=64&&87;(dùng cho con)-rxesi:mo=rxocon-tg;(xóa)-rxble:mo=rxocon-tg;(tạo lại con)

12. Lệnh reset trạm:-rxbli:mo=rxotg-tg,subord,force;(bloking-ngắt đi)-rxble:mo=rxotg-tg,subord;(deblok-tạo lại)

Lệnh reset cell:-rxbli:mo=rxotrx-TG-TRX,subord,force;;(lệnh blok TRX)-rxble:mo=rxotrx-TG-TRX,subord;;(deblok-tạo lại TRX)

13. dtbli:dip=mã trạm;

/ \|dip...|

DTBLI:DIP=+ +;|ALL|\ /

a, Parameters DIP=dip Digital path name Identifier(nhận ra, nhận dạng) 1 - 7 characters

ALL All digital paths

b, Function

The command initiates(bắt đầu) blocking of the specified digital path.The order(cấp, bậc, loại, hạng) remains after system restart.

14. Lệnh deblock dip:

/ \

Page 15: Tong Hop Lenh Ericsson

|dip...| DTBLE:DIP=+ +;

|ALL |\ /

a, Parameters

DIP=dip Digital Path (DIP) nameIdentifier 1 - 7 characters ALL All DIPs See the Application Information for block DIPST.

b, FunctionThis command deblocks the specified DIPs.The order remains after system restart.

15. Lệnh kiểm tra card(hoặc reset):-exemp:rp=all,em=all;-dirrp:rp=all;-blrpi:rp=RP,forced;(block)-blrpe:rp=RP;(deblock)

16. Lệnh không đưa vào dịch vụ:

a,  Command / \ |MO=mo... |RXESE:+ +; |MO=mo[,SUBORD]| \ /

b, Parameters

MO=mo Managed Object (MO) instance

See Application Information for block RXCTA for the format and the value range of this parameter. All MO classes are valid.

SUBORD

Subordinate MOs

All of the MO instances subordinate to the specified MO are

Page 16: Tong Hop Lenh Ericsson

included. Parameter SUBORD may be used for a Transceiver Group (TG) or Transceiver Controller (TRXC) in the Base Transceiver Station (BTS) logical model G01 and TG, Central Function (CF) or TRXC in the BTS logical model G12.

c, Function

This command orders the removing managed objects from service into prepost service. The MO must be manually blocked, that is in state COM. Up to 32 MOs can be specified. The MO instances(trường hợp,ví dụ) from different BTS logical models can not be mixed(hỗn hợp).

The answer printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT OUT OF SERVICE COMMAND RESULT will be printed giving the result of the command for all specified MO.

The subsequent result printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT OUT OF SERVICE COMMAND RESULT will be printed giving the result of the command for all specified MO.

The appearance of answer or result printout depends on exchange property OSSPRINTVER described in Application Information for block ROEPC.

If this MO instance was the last removed object from service in a TG, the observation alarm RADIO X-CEIVER ADMINISTRATION MANAGED OBJECTS IN TRANSCEIVER GROUP MANUALLY BLOCKED will be ceased.

The order in which the MOs are brought out of service in BTS logical model G01 is Time Slot (TS) and Receiver (RX) before the corresponding TRXC; TRXC, Timing Function (TF) and Transmitter (TX) before the corresponding TG.

The order in which the MOs are brought out of service in BTS logical model G12 is RX, TX and TS before the corresponding TRXC; Interface Switch (IS), Concentrator (CON), TRXC, TF, and Digital Path (DP) before the corresponding CF; CF before the corresponding TG.

The parameter SUBORD allows the specified MO instance and its subordinates to be brought out of service.

The order remains after system restart.

Page 17: Tong Hop Lenh Ericsson

17. Lệnh đưa vào dịch vụ:

a, Command / \ |MO=mo... |RXESI:+ +; |MO=mo[,SUBORD[,NOPRINT]] | \ /

b,  Parameters

MO=mo Managed Object (MO) instance

See Application Information for block RXCTA for format and value range of this parameter. All MO classes are valid.

NOPRINT

No result printout

This parameter suppresses the result printout when parameter SUBORD has been specified.

SUBORD Subordinate MOs

All of the MO instances subordinate to the specified MO are included. Parameter SUBORD may be used for a Transceiver Group (TG) or Transceiver Controller (TRXC) in the Base Transceiver Station (BTS) logical model G01 and TG, Central Function (CF) or TRXC in the BTS logical model G12.

c, Function

This command orders bringing Managed Objects into service from prepost service. Up to 32 MOs can be specified. The MOs must be defined, that is, in state DEF. The MO instances from different BTS logical models can not be mixed.

Once an MO has been brought into service it will initially be manually blocked, that is, in state COM. An attempt is then made to load the MO.

The answer printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT IN SERVICE COMMAND RESULT will be printed giving the result of the order for each of the MO instances specified by the MO parameter.

Page 18: Tong Hop Lenh Ericsson

A subsequent result printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT IN SERVICE RESULT will be given when the in-service order is completed for all MO instances.

If this MO is the first object brought into service in a TG, the observation alarm RADIO X-CEIVER ADMINISTRATION MANAGED OBJECTS IN TRANSCEIVER GROUP MANUALLY BLOCKED will be raised.

The order in which the MOs are brought into service in BTS logical model G01 is TG before the corresponding TRXC, Transmitter (TX) and Timing Function (TF); TRXC before the corresponding Time Slot (TS) and Receiver (RX).

The order in which the MOs are brought into service in BTS logical model G12 is TG before the corresponding CF; CF before the corresponding Interface Switch (IS), Concentrator (CON), TRXC, TF and Digital Path (DP); TRXC before the corresponding RX, TX and TS.

The parameter SUBORD, which may only be used in conjunction with a single MO instance, will print the status of that MO instance and all its subordinates. Upto a maximum of one-hundred and eighty-three MOs can be returned when specifying the SUBORD parameter.

When using parameter SUBORD, MO instances will only be processed if their superior MOs are also defined.

The parameter NOPRINT, which may only be used in conjunction with parameter SUBORD, suppresses the result printout.

The order remains after system restart.

18.Lệnh xem luồng và xem casce của trạm:

rxapp:mo=rxotg-TG;

19.Chý ý khi nâng cấp:

-nhảy tần-Thay đổi giữa con và uncon;(có thể phải xem cấu hình trước của trạm là dùng con hay uncon bằng lệnh: rmop:mo=rxotf-

Page 19: Tong Hop Lenh Ericsson

tg;). Nếu nâng lên cấu hình 4/4/4 thì phải dùng CON cho tất cả các TRX. RXMOC:MO=RXOCF-TG,TEI=62,SIG=CONC; RXMOI:MO=RXOCON- TG,DCP=64&&87; RXMOI:MO=RXOTRX- TG –TEI,DCP1=..,DCP2.., SIG=CONC;(Thêm các TRX có liên quan) RXMOI:MO=RXOTRX- TG -TEI, DCP1=..,DCP2.., SIG=CONC;(Thêm các TRX có liên quan)

RXMOC:MO=RXOTRX-TG-TRX,SIG=CONC;(Thay đổi các TRX không liên quan)

-Dùng lệnh halted và active:rlstc:cell=mã trạm1,state=halted;rlstc:cell=mã trạm2 ,state=halted;rlstc:cell=mã trạm3 ,state=halted;

rlstc:cell=mã trạm1,state=active;rlstc:cell=mã trạm2,state=active;

rlstc:cell=mã trạm3,state=active;Không dùng nhảy tần hay nhảy tần:-Change cells (when FHOP=BB and cell C has one CHGR=0) RLCCC:CELL=mã trạm1,SDCCH=2,TN=2; RLCFI:CELL=mã trạm1,DCHNO=;

-when FHOP=SY and cell C has two CHGRs=0,1! RLCCC:CELL= mã trạm1,CHGR=1,SDCCH=1,TN=1;

20. Xóa cell:rlcrp:cell=cell;rxtcp:cell= cell,moty=rxotg;rlvle:cell= cell,chtype=tch;(xóa giám sát)rlvle:cell= cell,chtype=sdcch;(xóa giám sát)

rldee:cell= cell(lệnh xóa)

21. Lệnh tăng SAE: saaep:sae=502,BLOCK=RTAPH;

Page 20: Tong Hop Lenh Ericsson

saaii:sae=502,BLOCK=RTAPH,ni=2048;(số ni phụ thuộc vào sự thay đổi của sae)RXMOI:MO=RXOTRX-67-6, TEI=6, DCP1=146, DCP2=147&148, SIG=UNCONC;rxmoe:mo=rxotrx-67-6;

22. Thêm tần số cho cell:-Them tan so: trạm BTS và thay rlccc giống như rlcfp theo cr: rlcfi:cell=sla0221,CHGR=0,DCHNO=68; rlcfi:cell=sla0222,CHGR=0,DCHNO=72;

Hiện tượng Unused hoặc Block TRX:-Trạm unused có thể do thiếu tần số.-Có thể halted lại cell rồi active nếu là Unused.(Xem lệnh RXMSP)-Dùng lệnh RLBDC để thay đổi NUMREQBPC(khi không thể thay đổi được kênh SDCCH) nếu là Unused.-Nếu không tăng được kênh SDCCH do TN(TN=1, hay TN=1&2)-Khi chuyển trạm mà một số trạm có hiện tượng block một số TRX thì có thể do nhầm luồng.-Do khai sai băng tần GSM900-GSM1800, công suất phát 47dbm-45dbm nếu Block.-Do gán sai TEI cho cell nên TX bị block.-Đối với chgr=2 trạm chung TG nếu TX unused và MISMATCH=cell thì có thể do lỗi khai sai TRX gán cho một tên cell của trạm khác.

23. Dùng cho trạm chung TG:RXMsc:MO=RXOTF-TG1,TFMODE=M;(tram chu) RXMsc:MO=RXOTF-TG2,TFMODE=S,TFCOMPNEG= 4580(do tối ưu-hỏi ứng cứu);

TFCOMPNEG

Timing function negative compensation value This is the distribution delay between the master TG and slave TG,plus own TG transmitter chain delay, minus the master TG transmitter chaindelay, given in nanoseconds.

Numeral 1 - 10000 TFCOMPPOS Timing function positive compensation value

This is the distribution delay between the master TG and slave TG,

Page 21: Tong Hop Lenh Ericsson

plus own TG transmitter chain delay, minus the master TG transmitter chaindelay, given in nanoseconds.

Numeral 0 - 10000 OMT

TF compensation value configured from OMT within the TG Synchronization function

TFMODE Timing function synchronization mode This is the mode of the timing function in the TG.M

Master, synchronized from the synchronization source and distributed to other TFsThe availability of this parameter value depends on commercial agreements.

S Slave, synchronized from other TFThe availability of this parameter value depends on commercial agreements.

SA Standalone, synchronized from synchronization source

24. Xóa TCH và thêm TCH:Rlstc:cell=…,state=halted;Rlcfe:cell=…,chgr=…,dchno=…;Rlcfi:cell=…,chgr=…,dchno=…;Rlstc:cell=…,state=active;

25. Lệnh xóa chgr và tần số:Rlstc:cell=…,state=halted;RLCHC:CELL=…,CHGR=…,HOP=on hoặc off,HSN=…hoặc 0,maio=…,bccd=…;(thay đổi Yes hoặc No)Rxtce:mo=rxotg-tg,cell=…,chgr…;(ngắt chgr)Rldge:cell=…,chgr…;(xóa chgr)Rlstc:cell=…,state=active;

26. Quan hệ giữa các cell:RLNRC:CELL=cell,CELLR=cellr,+…Nếu là xóa: RLNRE

Page 22: Tong Hop Lenh Ericsson

1,   Functiona, Format 1This command changes neighbour relation data for defined relations.Format 1 is used for the Ericsson1 algorithm. See parameter EVALTYPE in command RLLBC.Issuing a command of format 1 with all optional parameters included will result in a too long command line exceeding the maximum input buffer size of 140 characters. In this case, the command needs to be given two times with some optional parameters in the first command and the rest in the second command so that the maximum input buffer size is not exceeded.For details about the default values see Application Information for block RQCD.The order remains after system restart. b, Format 2This command changes neighbour relation data for defined relations.Format 2 is used for the Ericsson3 locating algorithm. See parameter EVALTYPE in command RLLBC.For details about the default values see Application Information for block RQCD.The order remains after system restart.

27. BA list và Relation:

BA list:

1.1   Command:

RLMFC:CELL=cell,MBCCHNO=mbcchno...[,LISTTYPE=listtype] [,MRNIC];

1.2   Parameters

CELL=cell Cell designation This is a symbolic name of a defined cell.

LISTTYPE=listtype

Type of measurement frequency list.

This parameter indicates in which mode the Mobile Station (MS) will measure on the frequencies in the list.

ACTIVE Measurement frequency list to be used by active MSs

IDLE Measurement frequency list to be used by idle MSs

Page 23: Tong Hop Lenh Ericsson

MBCCHNO=mbcchno Absolute Radio Frequency (RF) channel number for measurement on Broadcast Control Channel (BCCH) The number is the absolute RF channel number for the BCCH for cells to be measured on by a MS in the cell.Numeral 128 - 251 (GSM 800) Numeral 1 - 124 (GSM 900, P-band) Numeral 975 - 1023, 0 (GSM 900, G1-band) Numeral 512 - 885 (GSM 1800) Numeral 512 - 810 (GSM 1900)

MRNIC Measurement results not interpreted correctly At updating of the measurement frequencies, measurement results are not interpreted correctly for a period of time.

2   Function

This command initiates or adds frequencies that MSs will measure on in the cell. If the type of measurement frequency list is not specified, then both idle and active lists are changed. The command is only valid for internal cells, which are, cells belonging to the current Base Station Controller (BSC).

If MRNIC is specified, or the cell state is halted, then the updating of the measurement frequencies is performed immediately. In this case the measurement results are not interpreted correctly for a period of time. EXECUTED will be printed.

If MRNIC is not specified, the updating of the measurement frequencies is performed over a period of time and the measurement results are interpreted correctly. ORDERED will be printed and the result printout ADDITION OF CELL MEASUREMENT FREQUENCIES COMPLETED is received.

If the global system type is MIXED, it is possible to add frequencies in the combination of GSM 800 band, GSM 900 band, and GSM 1800 or GSM 1900 band.

The frequencies in G1 band can only be defined in a cell if the feature Extended GSM Frequency Band support is available. The availability of this feature depends on commercial agreements.

Basically up to 32 measurement frequencies can be defined in a frequency list.

If the global system type is MIXED, the following restrictions will apply according to the band in which the BCCH is defined and the combination of measurement frequency bands. The following restrictions apply to both IDLE and ACTIVE list types. In a few cases, when BCCH is in GSM 900 P band or undefined, the restrictions apply to IDLE list only (See Note 5 below). If the list type is not specified, it is set to BOTH. When the list type is set to BOTH, the restrictions are checked for both IDLE and ACTIVE lists.

Lỗi:

EXECUTEDORDEREDNOT ACCEPTEDfault type

Page 24: Tong Hop Lenh Ericsson

Fault type:

FUNCTION BUSY The function is busy.

FORMAT ERRORdetails

The command or a parameter was incorrectly specified.

UNREASONABLE VALUEdetails

The parameter was specified with an unreasonable value.

FAULT CODE 3 CELL NOT DEFINED

The cell is not defined.

FAULT CODE 14 MBCCHNO ALREADY GIVENdetails

The measurement frequency has already been given.

FAULT CODE 21 MAXIMUM NUMBER OF MBCCHNO EXCEEDED

The maximum number of measurement frequencies is exceeded. See chapter "2 Function" in this document for the maximum number of measurement frequencies that can be defined in a measurement frequency list.

FAULT CODE 38 COMMAND NOT VALID FOR EXTERNAL CELLS

The command must not be used for external cells, which are cells belonging to another BSC.

FAULT CODE 50 ACTIVE BA-LIST RECORDING IS ACTIVE

It is not possible to change neither the active list nor the idle list when the function Active BA-List Recording is active for the cell.

FAULT CODE 171 PARAMETER VALUE NOT SUPPORTED BY THIS EXCHANGEdetails

The possibility to define an MBCCHNO in G1 GSM band depends on commercial agreements. Contact the sales organization.

Relation:

1.1   Command

RLNRI:CELL=cell,CELLR=cellr[,SINGLE];

1.2   Parameters

CELL=cell Cell designation This is a symbolic name of a defined cell.

Page 25: Tong Hop Lenh Ericsson

CELLR=cellr

Related cell designation This is a symbolic name of a defined related cell.

SINGLE Single direction cell relation

This parameter defines the relation to be a one way relation between the cell and cellr. It means that handover can only be made from CELL to CELLR

When SINGLE is not given, the relation will be mutual, which means that handover in both directions is allowed.

2   Function

This command defines relations between cells. The type of relation between the cells can be either mutual or one-way. When relation is mutual, handover in both directions is allowed.

Mutual relation is default. Relation to an external cell, which is a cell in another Base Station Controller (BSC) or a cell using another Radio Access Technology (RAT), must be SINGLE.

To change the direction of a relation, the neighbour relation must be deleted using command RLNRE and a new relation defined.

It is allowed to define up to 64 Global System for Mobile Communication (GSM) neighbours and 64 UMTS Terrestrial Radio Access Network (UTRAN) Frequency Division Duplex (FDD) neighbours to a cell.

The order remains after system restart.

28 . Radio Control Cell, Dynamic HR Allocation Data, Change : RLDHC:CELL=cell+[,DHA=dha][,DTHAMR=dthamr][,DTHNAMR=dthnamr]+;

29. Thay đổi nhảy tần-BB hoặc SY:

In BTS Logical Model G01 /RXMOC:MO=mo...+[,FHOP=fhop][,SWVER=swver][,COMB=comb] \

[,RSITE=rsite][,TRACO=traco][,CONFACT=confact] \ [,CONFMD=confmd][,EMG=emg]+; /In BTS Logical Model G12 /RXMOC:MO=mo...+[,FHOP=fhop][,SWVER=swver][,COMB=comb]

Page 26: Tong Hop Lenh Ericsson

\ [,RSITE=rsite][,TRACO=traco][,CONFACT=confact] [,CONFMD=confmd][,SIGDEL=sigdel][,AHOP=ahop] \ [,ABISALLOC=abisalloc]+; /

30. Layer(Tầng, lớp):

RLLHC:CELL=HNI5093,LAYER=2,LAYERTHR=80,LAYERHYST=2,PSSTEMP=0,PTIMTEMP=0,FASTMSREG=OFF;

31. Thay đổi CLS state:rllci:cell=HTY0032;(active hay inactive) / |/ \/ \RLLCC:CELL=cell+|,CLSLEVEL=clslevel||,CLSACC=clsacc| |\ /\ / \ / \ |,HOCLSACC=hoclsacc| \ / \ / \/ \| |,RHYST=rhyst||,CLSRAMP=clsramp|+; \ /\ /| /

32. Thay đổi tham số HR cho cell:RLDMI:Cell=….;(bật hay tắt DMSUPP- RLDME) /RLDMC:CELL=cell+[,DMQB=dmqb] \[,DMQG=dmqg] [,DMQBAMR=dmqbamr] [,DMQBNAMR=dmqbnamr] [,DMQGAMR=dmqgamr] [,DMQGNAMR=dmqgnamr] [,DMTHAMR=dmthamr] \ [,DMTHNAMR=dmthnamr]+; /

33. Xem EM và xem TRX:EXEMP:RP=ALL,EM=ALL;ntcop:snt=all;34. Kiểm tra số TRXs:Command to check current number of TRXs:

Page 27: Tong Hop Lenh Ericsson

RXMSP:MOTY=RXOTRX;

Select the appropriate action according to the fault:

LOF or LOS Failure(mất khả năng) in receive direction(sự điều khiển) detected(nhận ra,phát hiện ra) by local termination equipment. Go to Step 34.

ALL1 or AIS Alarm indication(dấu hiệu) signal transmitted by remote(từ xa, ở xa) end termination equipment due to(do đó, nhờ có) failure upstreams. Further action is outside the scope of this Operational Instruction. Consult the next level of maintenance support and return to Step 50 in this Operational Instruction.

RDI Remote defect(mất hụt) indication. Failure in transmit(truyền ,phát tín hiệu) direction detected by remote end termination equipment. Go to Step 34.

ERATE or CSES Severe degradation of signal. Go to Step 43. LOMF or REFM Faults related to multiframe signalling (TS16). Go to Step 38.

AISM Alarm indication signal in TS16 transmitted by remote end termination equipment due to failure affecting the signalling upstreams. Further action is outside the scope of this Operational Instruction. Consult the next level of maintenance support and return to Step 50 in this Operational Instruction.Other faults Further action is outside the scope of this Operational Instruction. Consult the next level of maintenance support and return to Step 50 in this Operational Instruction.

35. Khởi tạo đường dẫn cuộc gọi:RAPTI:LCH=2485;

Tracing(dau vet, lan theo) and printing(in ra) of connections using logical channel number 2485 is made.36. Xem số TG dang hoat dong va so TRX dang su dung:

rxmsp:moty=rxotg;rxmsp:moty=rxotrx;

37. Lỗi về LRDEC: FAULT CODE 50 ACTIVE BA-LIST RECORDING(đã được ghi) IS ACTIVE

When the cell state is ACTIVE and Active BA-List Recording is active for the cell, it is not possible to change the RF channel for BCCH.

Sữa lỗi 1:

a,   Command

/ \ |rid...|RABRP:RID=+ +; |ALL |

Page 28: Tong Hop Lenh Ericsson

\ /

b,   ParametersRID=rid Active BA-list Recording Identity Identifier BARID00 - BARID63

ALL All RIDs

C,FunctionThis command is used to print the details of one, severalor all RIDs. The printout ACTIVE BA-LIST RECORDING DETAILSwill be given.The order does not remain after system restart.

Sữa lỗi 2:

A,   CommandRABRE:RID=rid[,MRNIC];

B,   ParametersMRNIC Measurement Results Not Interpreted(trình diện,thể hiện) Correctly(đúng đắn,phù hợp) When re-creating the active BA-lists, Measurement Results are interpreted incorrectly during(trong thời gian) a few minutes.

RID=rid Active BA-list Recording Identity Identifier BARID00 - BARID63

C,  Function

This command is used to interrupt a recording for oneRID, before the duration time has elapsed.The command is only accepted for RIDs that are in stateRECORDING or CONFIGURATION OF BA-LISTS. The state of theinterrupted RID will then change to RECORDING COMPLETE.If MRNIC is specified, then the re-creation of the activeBA-lists is performed immediately. In this case themeasurement results are interpreted incorrectly duringa few minutes, e.g. a faulty handover can occur. Otherwise,the re-creation of the active BA-lists is performed overa period of time and the measurement results areinterpreted correctly.The printout ACTIVE BA-LIST RECORDING TERMINATION RESULT will be given when the recording is ended. The printout isrouted both to the ordering IO device and to the IO deviceindicated by the printout category.The order does not remain after system restart.

D,   Examples

Page 29: Tong Hop Lenh Ericsson

3.1   Example 1

RABRE:RID=BARID00,MRNIC;The active BA-list recording will be terminatedfor the RID BARID00. When updating the active BA-lists,measurement result will not be interpreted correctlyfor a period of time.

38. Liên qua đến BA-list(dạng khác có thể chưa dùng)

/ \ |,CELL=cell... | | / \| |,CELL=ALL |,CSYSTYPE=csystype|| RABDE:RID=rid + \ /+; | / \ | | |tmbcchno...| | |,TMBCCHNO= + + | | |ALL | | \ /

a, ParametersCELL=cell Cell designation

Symbolic name, maximum 7 characters

ALL All Internal cells

CSYSTYPE=csystype

System Type Identifier GSM800

GSM 800GSM900

GSM 900GSM1800

GSM 1800GSM1900

GSM 1900RID=rid Active BA-list Recording Identity

Identifier BARID00 - BARID63 TMBCCHNO=tmbcchno

Absolute Radio Frequency (RF) channel number for test measurement on BCCHNumeral 128 - 251 (GSM 800) Numeral 0 - 124 (GSM 900) Numeral 975 - 1023 (GSM 900) Numeral 512 - 885 (GSM 1800) Numeral 512 - 810 (GSM 1900)

The number is the absolute RF channel number for the BCCH for cells to be measured on by a mobile station in the cell.

ALL All TMBCCHNOs connected to the RID

Page 30: Tong Hop Lenh Ericsson

b,Function

This command removes cells or frequencies from an active recording. During the recording the frequencies are included in the active BCCH Allocation (BA) lists, for all cells connected to the RID.

It is possible to remove one cell, several cells, all cells or all cells of a specific system type from a RID or remove one frequency, several frequencies or all frequencies from a RID.

The command is only accepted for RIDs that are in state ALLOCATED, USED or RECORDING COMPLETE.

If all cells are removed from the RID the state is changed to ALLOCATED.

The order does not remain after system restart.

C, Examples

- Example 1RABDE:RID=BARID15,CELL=KNA11;

Removes the cell KNA11 from the RID BARID15.

-   Example 2RABDE:RID=BARID25,CELL=ALL,CSYSTYPE=GSM1900;

Removes all cells of the system type GSM 1900 from the RID BARID25.

-   Example 3RABDE:RID=BARID37,TMBCCHNO=530&&550;

Removes TMBCCHNOs 530 up to 550 from the RIDBARID37.

-   Example 4RABDE:RID=BARID53,TMBCCHNO=ALL;

Removes all the test BCCH frequencies from the RID BARID53.

39.Lệnh print các ETM:

1.1   Command / \ |SDIP=sdip... |TPSTP:[IO=io,]+ +; |SDIP=ALL[,STATE=state...]| \ /

Page 31: Tong Hop Lenh Ericsson

1.2   ParametersIO=io Input/Output (IO) device name

Identifier 1 - 7 characters SDIP=sdip Synchronous Digital Path (SDIP) name

Identifier 1 - 7 characters ALL

All SDIPsSTATE=state State of SDIP

BLOC Blocked

PBLOC Partly blocked

TRAFBLOC Traffic blocked

TRAFLIM Traffic limited

WO Working

2   Function

This command prints the state of specified SDIP on specified or default IO device.

Printout SYNCHRONOUS DIGITAL PATH STATE is received.

Up to 10 SDIPs can be specified in each command.

The order does not remain after system restart.

3   Examples

3.1   Example 1TPSTP:SDIP=LONDON;

The state of SDIP LONDON is printed.

3.2   Example 2TPSTP:IO=AT-4,SDIP=LONDON&OSLO;

The state of the SDIPs LONDON and OSLO is printed on IO device AT-4.

3.3   Example 3TPSTP:SDIP=ALL;

The state of all SDIPs is printed.

3.4   Example 4TPSTP:IO=AT-4,SDIP=ALL,STATE=WO&BLOC;

All working and all blocked SDIPs are printed on IO device AT-4.

Page 32: Tong Hop Lenh Ericsson

40. Deblock các ETM:

1.1   Command / // \\\ | ||,MS=ms...||| |sdip|+,HP +|| | ||,HP=hp...|||TPBLE:SDIP=+ ||,LP=lp...||+; | \\ //| |sdip... | | | |ALL | \ /

1.2   ParametersHP=hp Higher order Path (HP)

For the value ranges, see the Application Information for SDIP owning block.

LP=lp Lower order Path (LP)

For the value ranges, see the Application Information for SDIP owning block.

MS=ms Multiplex Section (MS)

For the value ranges, see the Application Information for SDIP owning block.

SDIP=sdip

Synchronous Digital Path (SDIP) nameIdentifier 1 - 7 characters ALL

All SDIPs

2   Function

This command deblocks either the whole SDIP including all existing lower layers, or only the MS, the HP, or the LP when they are specified.

Result printout SYNCHRONOUS DIGITAL PATH DEBLOCKING RESULT is received.

Up to 10 SDIPs can be specified in each command.

The order remains after system restart.

3   Examples

3.1   Example 1TPBLE:SDIP=LONDON;

The whole SDIP LONDON is manually deblocked.

Page 33: Tong Hop Lenh Ericsson

3.2   Example 2TPBLE:SDIP=LONDON,MS=MS-0&-1;

The MS-0 and MS-1 within SDIP LONDON are manually deblocked.

3.3   Example 3TPBLE:SDIP=LONDON,HP;

The HP within SDIP LONDON is manually deblocked.

3.4   Example 4TPBLE:SDIP=LONDON,LP=VC12-0&&-47;

The LPs VC12-0 to VC12-47 within SDIP LONDON are manually deblocked.

3.5   Example 5TPBLE:SDIP=LONDON&OSLO&NACKA;

The SDIPs LONDON, OSLO, and NACKA are manually deblocked.

3.6   Example 6TPBLE:SDIP=ALL;

All SDIPs are manually deblocked.

3.7   Example 7TPBLE:SDIP=CHICAGO,HP=STS1-0&-1

The HPs STS1-0 and STS1-1 within SDIP CHICAGO are manually deblocked.

41. Dùng để blocking RP:

1.1   Command

BLRPI:RP=rp[,FORCED];

1.2   Parameters

RP=rp Regional Processor (RP) addressNumeral 0 - 1023 The maximum value is defined by the Size Alteration Event (SAE) 304

FORCED Blocks RP regardless of Extension Module (EM) state and device state.

2   Function

Page 34: Tong Hop Lenh Ericsson

This command is used when blocking an RP, where the logical state of the RP is set to Manually Blocked (MB). The bus senders are blocked from sending signals on the RP bus.

In the case of RPs with an EM bus, the control of the connected equipment, EMs, is transferred automatically, if possible, to the twin RP through local restarts of the EMs.

If the control of EMs cannot be transferred, all EMs linked to the RP and all devices connected to the EMs must be manually blocked before the command can be accepted.

For some RPs without EM bus it is sufficient that all devices connected to the EMs are manually blocked before the command can be accepted.

If the parameter FORCED is given, the RP is blocked regardless of EM state and device state. This parameter shall be used with care as it can result in traffic disturbance. Special checks requested by EM owner to ensure that critical IO-channel system resources are not lost, are still done.

For some RP types without an EM bus, the commands for blocking and deblocking of EM are not applicable. The operational state for the EM is then controlled by blocking and deblocking the RP. For these RPs, some checks normally performed at BLEMI are performed at BLRPI instead.

The order remains after system restart.

3   Examples

3.1   Example 1

BLRPI:RP=2;

An RP with address 2 is blocked (if EM state and device state are manually blocked).

3.2   Example 2

BLRPI:RP=5,FORCED;

An RP with address 5 is blocked regardless of EM state and device state.

42. Remove EM(expension module):

1.1   Command

EXEME:RP=rp[,RPT=rpt],EM=em;

1.2   Parameters

EM=em Extension Module (EM) addressNumeral 0 - 63

Page 35: Tong Hop Lenh Ericsson

RP=rp Regional Processor (RP) addressNumeral 0 - 1023 Actual maximum value is defined by Size Alteration Event (SAE) 304.

RPT=rpt RP address for twin(sinh đôi, cặp đôi) RPNumeral 0 - 1023 Actual maximum value is defined by SAE304.

2   Function

The command is used in order to remove the definition of an EM. Devices connected to the EM must be manually blocked. Also the EM must be blocked except(trừ ra, loại ra) for the RP-types for which EM blocking command is not applicable(có thể ứng dụng được). For these RP-types the RP must be blocked instead(thay vi, thay cho). If the EM is controlled by an RP pair, both the RP addresses must be indicated(chi ra).

The order remains after system restart.

3   Examples

3.1   Example 1

EXEME:RP=16,RPT=17,EM=4;

The definition of the EM with address 4, in the RP pair which consists of RPs 16 and 17, is removed.

3.2   Example 2

EXEME:RP=50,EM=5;

The definition of the EM with address 5, in the single RP 50, is removed.

43. Lệnh này dùng để xóa Regional Software Units (RSU):

1.1   Command

/ \ | / \| | |ALL || / \ |SUNAME=+ +| |RP=rp... | | |suname||EXRUE:+ +,+ \ /+; |RP=rp,RPT=rpt| | / \ | \ / | |ALL | | |SUID=+ + | | |suid| | | \ / | \ /

1.2   Parameters

Page 36: Tong Hop Lenh Ericsson

RP=rp Regional Processor (RP) addressNumeral 0 - 1023 The maximum value is defined by Size Alteration Event (SAE) 304.

RPT=rpt Regional Processor Twin (RPT) addressNumeral 0 - 1023 The maximum value is defined by SAE=304.

SUID=suid Software Unit (SU) identityIdentifier 1 - 32 characters If the identifier contains any character, other than letters or digits then the string must be given within quotation marks.

SUNAME=suname

SU nameIdentifier 1 - 8 characters

2   Function

Command EXRUE is used to delete defined Regional Software Units (RSU) in an RP (RP pair) or in a suite of RPs. The specified suite of RPs must not consist of more than 128 RPs.

The specified RP or RPs must be manually blocked (not blocked for repair or blocked for function change). Parameter SUID must be specified if more than one version of the specified SU is defined.

If a specific SUNAME (SUID) is given, it must be defined in all the specified RPs.

The RSUs must be deleted at the same time for both RPs in an RP pair. The two addresses in the pair can be specified in two different ways as follows:

With parameters RP and RPT With parameter RP for both addresses

If the command is used to delete definitions of SUs in more than one RP (RP pair) at a time, all the RP addresses (including the RPT addresses) must be specified with parameter RP.

An RSU of type Firmware Replacement Package (FRP) shall not be deleted unless it shall be replaced or it is faulty. This is to avoid that, at repair of RPs, an RP board is entered and started with an old FRP RSU. Although an FRP RSU is removed by command EXRUE the FRP RSU will continue to be working in the RP (if it once has been loaded to the RP).

The order remains after system restart.

3   Examples

3.1   Example 1

EXRUE:RP=7,RPT=8,SUNAME=RPFDR;

The definition of the RSU with name RPFDR in RP 7 and RPT 8 is deleted.

3.2   Example 2

Page 37: Tong Hop Lenh Ericsson

EXRUE:RP=7,SUID="5/CAA1053092/1R1A02";

The definition of an RSU with product identity 5/CAA 105 3092/1 R1A02 in RP 7 is deleted.

3.3   Example 3

EXRUE:RP=7&20,SUNAME=RPFDR;

The definition of the RSU with name RPFDR in RP 7 and RP 20 is deleted.

3.4   Example 4

EXRUE:RP=7&&20,SUNAME=RPFDR;

The definition of the RSU with name RPFDR in the RP suite RP 7 through RP 20 is deleted.

3.5   Example 5

EXRUE:RP=7&&20,SUNAME=ALL;

All RSU definitions in the RP suite RP 7 through RP 20 are deleted.

3.6   Example 6

EXRUE:RP=25,SUID="9000/CXC 152 001 R1A01";

The FRP RSU definition with product identity 9000/CXC 152 001 R1A01 in RP 25 is deleted. If loaded to the RP, the FRP will not be removed from the RP.

44. Lệnh này dùng để remove các RP:

1.1   Command

EXRPE:RP=rp[,RPT=rpt];

1.2   Parameters

RP=rp Regional Processor (RP) addressNumeral 0 - 1023 The maximum value is defined by Size Alteration Event (SAE) 304.

RPT=rpt RP twin addressNumeral 0 - 1023 The maximum value is defined by SAE 304.

2   Function

This command is used in order to remove the definition of an RP or an RP pair.

Page 38: Tong Hop Lenh Ericsson

The command requires that the affected RP is manually blocked and and that the definition of associated equipment has been removed.

If the RP is loadable, all Software Unit (SU) definitions must also be removed (by command EXRUE).

The order remains after system restart.

3   Examples

3.1   Example 1

EXRPE:RP=17;

The definition of a single RP, with address 17, is removed.

3.2   Example 2

EXRPE:RP=17,RPT=8;

The definition of an RP pair, with addresses 17 and 8, is removed.

45. Khởi tạo lại RP:

1.1   Command

EXRPI:RP=rp[,RPT=rpt],TYPE=type[,DEFRSU];

1.2   Parameters

DEFRSU Define Regional Software UnitsRP=rp Regional Processor (RP) address

Numeral 0 - 1023 The maximum value is defined by Size Alteration Event (SAE) 304.

RPT=rpt RP twin addressNumeral 0 - 1023 The maximum value is defined by SAE 304.

TYPE=type RP typeText string 1 - 7 characters

2   Function

This command initiates RP equipment for the specified RP-address (or addresses) and for the specified type of RP.

If parameter DEFRSU is given then default Operating System (OS) Regional Software Units (RSU), as specified in database table RPSDEFOSRSUS, are defined for the RP. The effect of parameter DEFRSU is the same as if these RSUs had been defined by command EXRUI after command EXRPI.

Page 39: Tong Hop Lenh Ericsson

Possible RP types are described in Application Information for block RPADM.

All valid types of RPs, with characteristics and properties of the different types, can be listed by printing the database tables RPSRPTYPES, RPSTYPESTOPROPS and RPSRPPROPERTIES.Use generic DBS print command DBTSP.

The order remains after system restart.

Note:   Also an RSU of type Firmware Replacement Package (FRP) can be defined for the RPs by use of parameter DEFRSU. FRP RSUs can be included in the DBS table RPSDEFOSRSUS.

3   Examples

3.1   Example 1

EXRPI:RP=17,TYPE=RPM1A;

An RP of type RPM1A is defined. It has RP address 17.

3.2   Example 2

EXRPI:RP=17,RPT=8,TYPE=RPM6A;

An RP pair of type RPM6A is defined. The pair will control the same EMs. The pair has RP addresses 17 and 8.

3.3   Example 3

EXRPI:RP=30,RPT=31,TYPE=RPM2B;

An RP pair of type RPM2B is defined. It has RP addresses 30 and 31.

3.4   Example 4

EXRPI:RP=20,type=STC1A;

A Signalling Terminal Central (STC) with RP address 20 is defined.

3.5   Example 5

EXRPI:RP=40,TYPE=RPI1A,DEFRSU;

An RP of type RPI1A is defined. Default OS RSUs are defined for the RP. The RP has RP address 40.

46. Khởi tạo các kết nối SNT:

1.1   Command

Page 40: Tong Hop Lenh Ericsson

/ \ |[SNTP=sntp,]SNT=snt...[,IDLEP=idlep] | | | |SNTP=sntp...,SNT=snt[,IDLEP=idlep] | | |NTCOI:+SNTP=sntp,SNT=snt,EQLEV=eqlev,PROT=prot[,IDLEP=idlep] +,SNTV=sntv; | | |SNTP=sntp,SNT=snt[,MODE=mode][,PROT=prot][,IDLEP=idlep]| | | |EXTP=extp,SNT=snt[,MG=mg] | \ /

1.2   Parameters

EQLEV=eqlev

Equipping level

This parameter is only intended for Switching Network Terminal (SNT) with Subordinate SNTs and protection.

For value range, see the Application Information for SNT-owning block. EXTP=extp External Hardware Connection Point

This parameter is only intended for the connection of SNT to External Hardware Switch.

If the SNT-owning block supports parameter MG then the EXTP parameter value has to be written within quotation marks.

For string range, see the Application Information for SNT-owning block. IDLEP=idlep

Idle pattern For value range, see the Application Information for block SNTH.

MG=mg Media Gateway This parameter is only intended for the connection of SNT to External Hardware Switch.Text string 1 - 7 characters

MODE=mode Mode

This parameter is only intended for the connection of DL34 SNTs.

For value range, see the Application Information for SNT-owning block. PROT=prot Protection

This parameter indicates if equipment protection is used.

This parameter is only intended for SNT with Subordinate SNTs and protection.

For value range, see the Application Information for SNT-owning block. SNT=snt Switching network terminal

Expressed as snt-n where:

Page 41: Tong Hop Lenh Ericsson

snt Switching network terminal typeIdentifier 1 - 13 characters

n Switching network terminal numberNumeral 0 - 65535

The maximum value of the switching network terminal number is determined by Size Alteration Event (SAE) in the SNT-owning block (SAE 529).

For alternative expressions, see the Application Information for block TRAN and the relevant SNT-owning block.

SNTP=sntp Switching network terminal connection point

Expressed as a-b-c where:

a Switch unit nameIdentifier 1 - 7 characters

b Switch unit number

c Switching network terminal point

See Application Information for block TRASAD.

Expressed as a-b-f or a-d-e-f where:

a Switch unit nameIdentifier 1 - 7 characters

b Switch unit number

d Switch unit row number

e Switch unit column number

f Digital link number See Application Information for block SNTH

SNTV=sntv Switching network terminal variant For value range, see the Application Information for SNT-owning block.

2   Function

This command connects a Switching Network Terminal (SNT) to a Group Switch (GS), a Subscriber Switch (SS), or an External Switch. For SNTs with subordinate SNTs or SNTs to be connected to an external switch, one SNT can be connected in one command issue. For SNTs of any other type, the maximum of 32 SNTs can be connected. For an SNT with several hardware connections to the GS, the connection is made in consecutive order according to the designations of these connections.

Page 42: Tong Hop Lenh Ericsson

For DL3 SNTs with subordinate SNTs the number of the subordinate SNTs to be connected are indicated by parameter EQLEV. Also the equipment protection can be specified for this type of SNT with parameter PROT .

For DL34 SNTs with subordinate SNTs, the number of Multiple Points (MUPs) to be reserved by the GS is indicated by parameter MODE.

For SNTs connected to an External Switch, parameter SNTP is not allowed. Parameter EXTP should be used instead indicating the connection point (port) of the External Hardware Switch. If this SNT supports connection to a Media Gateway (MG), parameter MG should be used indicating the MG name.

Parameter IDLEP may be specified only when this parameter is supported by the specified SNTs.

Note:   Three adaptation blocks exist in the AXE, SNTPCD, SNTET and SNTMJ. These are used to connect device types which are not SNT owners. For SNTs connected in adaptation blocks, the SNT type is defined when the first SNT of that type is connected. This is not specified in a separate parameter but is implicit in the command.

The order remains after system restart.

3   Examples

3.1   Example 1

NTCOI:SNT=SNTPCD32-2,SNTP=TSM-1-2,SNTV=5;

The SNT of type SNTPCD 32, variant 5 and individual 2 is connected to the SNT connection point 2 in Time Switch Module (TSM) 1.

3.2   Example 2

NTCOI:SNT=ET1-0,SNTV=1;

The SNT of type ET1, variant 1 and individual 0 is connected to the SNT connection.

3.3   Example 3

NTCOI:SNTP=TSM-12-3&&-4,SNT=ASAM-0,SNTV=1;

The SNT of type ASAM, variant 1 and individual 0 is connected to the SNT connection points 3 and 4 in TSM 12.

3.4   Example 4

NTCOI:SNTP=TSM-1-0,SNT=SNTETET8-2&&-4,SNTV=2;

The SNTs of type SNTETET8, variant 2, with individuals 2, 3, and 4 are connected in consecutive order to the SNT connection points 0,1 and 2 in TSM 1.

Page 43: Tong Hop Lenh Ericsson

3.5   Example 5

NTCOI:SNTP=TSM-8-13,SNT=SNTETET8-2&&-6,SNTV=2;

The SNTs of type SNTETET8, variant 2, with individuals 2,3 and 4 are connected in consecutive order to the SNT connection points 13,14 and 15 in TSM 8. Since connection position 15 is the last position in TSM 8, the sequence continues in TSM 9. Therefore individuals 5 and 6 are connected to connection points 0 and 1 in TSM 9.

3.6   Example 6

NTCOI:SNT=ET155-2,SNTP=TSM-1-0,SNTV=1,EQLEV=1,PROT=1;

The SNT ET155, individual 2 of variant 1 is connected to the TSM 1. The EQLEV parameter indicates that one SUBSNT is connected to the switch. Also that the SNT has equipment protection is defined.

3.7   Example 7

NTCOI:SNT=ET155-3,SNTP=TSM-1-0,SNTV=1,EQLEV=3,PROT=3;

The SNT ET155, individual 3 of variant 1, is connected in consecutive order to the TSM 1, 2 and 3. The EQLEV parameter indicates that three subordinate SNTs are connected to the switch. Also that the SNT has equipment protection is defined.

3.8   Example 8

NTCOI:SNT=MBTRCS-0,SNTP=TSM-0-0&TSM-1-0,SNTV=1;

The SNT MBTRCS, individual 0 of variant 1, is connected to TSM 0 and TSM 1 at the same connection point of both TSMs (0 in this example).

3.9   Example 9

NTCOI:SNT=VET-2, EXTP=32-4-8-5, SNTV=0;

The VET SNT, individual 2 of variant 0 is connected to an external hardware connection point which is positioned in subrack 32 in slot 4 on subport 5 of port 8.

3.10   Example 10

NTCOI:SNTP=MUX3-8-4,SNT=SNTETET8-2&&-6,SNTV=2,IDLEP=1;

The SNTs of type SNTETET8, variant 2, with individuals 2 to 6, are connected in consecutive order to the access points 4,5,6,7 and 8 in MUX3 8.

3.11   Example 11

NTCOI:SNT=ET155-2,SNTP=XM-1-2-8,SNTV=1,MODE=128,PROT=1;

Page 44: Tong Hop Lenh Ericsson

The SNT ET155, individual 2 of variant 1 is connected to the XM in row 1 and column 2. The number of MUPs to be allocated by the GS for this SNT is specified in parameter MODE. Also equipment protection for the SNT is defined.

3.12   Example 12

NTCOI:EXTP="28-2-5-3",SNT=VET-1,MG=AXDWA,SNTV=0;

The VET SNT, individual 1 of variant 0, is connected to an external hardware connection point of the MG AXDWA which is positioned in subrack 28 in slot 2 on subport 3 of port 5.

47. Khởi tạo và test các SNT:

1.1   Command

NTTEI:SNT=snt [,SUBSNT=subsnt];

1.2   Parameters

SNT=snt Switching Network Terminal (SNT)

Expressed as snt-n where:

snt SNT typeIdentifier 1 - 13 characters

n SNT numberNumeral 0 - 65535

The maximum value of the SNT number, is determined by the Size Alteration Event (SAE) in the SNT owning block (SAE 529).

For alternative expressions, see the Application Information for block TRAN and the relevant SNT owning block.

SUBSNT=subsnt

Subordinate switching network terminal For value ranges, see the Application Information for the relevant SNT owning block.

2   Function

This command initiates testing of a manually blocked SNT or a subordinate SNT. When an SNT with subordinate SNTs is specified in the command, only the specified subordinate SNTs are tested. Otherwise, the complete SNT is tested.

Result printout SWITCHING NETWORK TERMINAL TEST RESULT is received.

The order does not remain after system restart.

Page 45: Tong Hop Lenh Ericsson

3   Examples

3.1   Example 1

NTTEI:SNT=SNTPCD32-9;

SNT 9 of type PCD32 is tested.

3.2   Example 2

NTTEI:SNT=SNTETBT4-2;

SNT 2 controlled by device block BT4 is tested.

3.3   Example 3

NTTEI:SNT=ET155-4,SUBSNT=3;

Subordinate SNT 3 of ET155 SNT 4 is tested.

48. Deblock các SNT:

1.1   Command

/ \ |snt... |NTBLE:SNT=+ +; |snt [,SUBSNT=subsnt...]| \ /

49. XM bi block:

1.2   Parameters

SNT=snt Switching Network Terminal (SNT)

Expressed as snt-n where:

snt Switching network terminal typeIdentifier 1 - 13 characters

n Switching network terminal numberNumeral 0 - 65535

The maximum value of the switching network terminal number, is determined by the Size Alteration Event (SAE) in the SNT owning block (SAE 529).

For alternative expressions, see the Application Information for block TRAN and the relevant SNT owning block.

Page 46: Tong Hop Lenh Ericsson

SUBSNT=subsnt

Subordinate switching network terminal For value ranges, see the Application Information for the relevant SNT owning block.

2   Function

This command deblocks an SNT or a subordinate SNT. When an SNT with subordinate SNTs is specified in the command, only the specified subordinate SNTs are deblocked. Otherwise, the complete SNT is deblocked.

A maximum of 128 SNTs or 1 SNT with SUBSNTs or specified SUBSNTs, can be specified in one command issue.

The supervision is activated for the entire deblocked SNT, or for the deblocked subordinate SNT.

Result printout SWITCHING NETWORK TERMINAL DEBLOCKING RESULT is received.

The order remains after system restart.

3   Examples

3.1   Example 1

NTBLE:SNT=SNTETBT3-18&&-21;

SNT of type SNTETBT3 with individuals 18, 19, 20, and 21 are manually deblocked.

3.2   Example 2

NTBLE:SNT=ET6-27&&-29;

SNT of type ET6 with individuals 27, 28, and 29 are manually deblocked.

3.3   Example 3

NTBLE:SNT=ET155-0,SUBSNT=0&&3;

Subordinate SNT 0, 1, 2, and 3 of ET155 SNT 0 are manually deblocked.

3.4   Example 4

NTBLE:SNT=ET155-0&&-2;

SNT of type ET155 with individuals 0, 1, and 2 are manually deblocked.

3.5   Example 5

NTBLE:SNT=ET155-10,SUBSNT=1&5;

Page 47: Tong Hop Lenh Ericsson

Subordinate SNT 1 and 5 of ET155 SNT 10 are manually deblocked.

1.1   Command / / / \ \ \ | |UNIT=unit...|,DETAIL| | |GDSTP|:+ \ / + |; | |TYPE=type | | \ \ / /

1.2   ParametersDETAIL Detailed printoutTYPE=type Type of Distributed Group Switch unit to be printedUNIT=unit Distributed Group Switch unit identifier

Expressed as clm-n, mux-p-n, or xm-p-r-c where:

c Individual column number

clm Clock module name

mux Multiplexer unit name

n Unit number

p Plane identifier

r Individual row number

xm Switch matrix unit name

A Plane A

B Plane B

Note:   See Application Information for block GIOH and each unit specific AI.

2   Function

This command prints the state of Distributed Group Switch units.

The command accepts the specification of a single unit, multiple units of varying types, all units of a particular type, or all units in the Distributed Group Switch.

If parameter TYPE is specified, the state of all the Distributed Group Switch units of the type specified in the command are printed.

Repetition is allowed for all unit types.

For switch matrix units, repetition is only allowed on the column identifier.

Page 48: Tong Hop Lenh Ericsson

When a range of units is specified and if no units are connected to the Distributed Group Switch in the given range then NONE is printed. Otherwise, only the state of the units that are connected are printed.

If parameter DETAIL is specified, the states of the whole chain of downstream Distributed Group Switch units connected to the units specified in the command are printed. It is not allowed to specify a Clock unit together with parameter DETAIL.

The answer printout DISTRIBUTED GROUP SWITCH STATE is received.

The order does not remain after system restart.

1.1   CommandGDBLI:UNIT=unit;

1.2   ParametersUNIT=unit

Distributed Group Switch unit

Expressed as clm-n, mux-p-n, or xm-p-r-c where:

c Individual column number

clm Clock Module (CLM) name

mux Multiplexer unit name

n Unit number

p Plane identifier

A Plane A

B Plane B

r Individual row number

xm Switch Matrix (XM) unit name

See Application Information for block GIOH and each unit specific AI (CLM, MUX3, MUX34, MUXSP , MUXTS, XM).

1.3   Dialogue ParametersNO; Manual blocking of the specified CLM is not to take place.YES; Manual blocking of the specified CLM unit is to take place.

2   Function

This command initiates blocking of a unit in the Distributed Group Switch, provided the blocking will not result in traffic restrictions.

Result printout DISTRIBUTED GROUP SWITCH UNIT BLOCKING RESULT is received.

Page 49: Tong Hop Lenh Ericsson

Manual blocking of automatically blocked units is always permitted, but not in units which are not connected.

Manual blocking of a CLM means considerable risk for the exchange as there are only two CLMs in the Distributed Group Switch. For this reason unnecessary blocking must be avoided. In the case of an unnecessary blocking attempt on a CLM, the dialogue procedure starts and answer printout WARNING, ACCEPTANCE MEANS CONSIDERABLE RISK FOR THE WHOLE EXCHANGE, ANSWER WITH YES IF YOU WANT TO CONTINUE will be received. Indicate with YES if the blocking is to be executed. Indicate with NO if the blocking is not to be executed, and the printout BLOCKING ORDER CANCELLED will be received.

An observation alarm DISTRIBUTED GROUP SWITCH UNIT MANUALLY BLOCKED indicating that the unit is now blocked is added in the alarm list.

If the alarm DISTRIBUTED GROUP SWITCH FAULT is present for the unit being manually blocked, then the fault alarm is ceased.

This command cannot be given immediately after an initial start or if the switch type is not initiated.

The order remains after system restart.

1.1   CommandGDBLE:UNIT=unit;

1.2   ParametersUNIT=unit

Distributed Group Switch unit identifier

Expressed as clm-n, mux-p-n or xm-p-r-c where:

c Individual column number

clm Clock Module (CLM) name

mux Multiplexer unit name

n Unit number

p Plane identifier

A Plane A

B Plane B

r Individual row number

xm Switch Matrix (XM) unit name

See Application Information for block GIOH and each unit specific AI (CLM, MUX3, MUX34, MUXSP , MUXTS, XM).

2   Function

Page 50: Tong Hop Lenh Ericsson

This command ends the blocking of a unit in the Distributed Group Switch.

Result printout DISTRIBUTED GROUP SWITCH UNIT DEBLOCKING RESULT is received.

An observation alarm DISTRIBUTED GROUP SWITCH UNIT MANUALLY BLOCKED indicating that the unit was blocked is no longer in the alarm list.

This command cannot be given immediately after an initial start or if the switch type is not initiated.

The order remains after system restart.

3   Examples

3.1   Example 1GDBLE:UNIT=CLM-1;

This command ends the blocking of CLM unit 1.

3.2   Example 2GDBLE:UNIT=MUX3-B-2;

This command ends the blocking of the Digital Link version 3 Multiplexer (MUX3) in plane B, unit 2.

3.3   Example 3GDBLE:UNIT=MUX34-A-3;

This command ends the blocking of the Digital Link adaptable from version 3 to 4 Multiplexer (MUX34) in plane A, unit 3.

3.4   Example 4GDBLE:UNIT=MUXSP-B-1;

This command ends the blocking of the Multiplexer based on Space Switch Module (MUXSP) in plane B, unit 1.

3.5   Example 5GDBLE:UNIT=MUXTS-A-2;

This command ends the blocking of the Multiplexer based on Time Switch Module (MUXTS) in plane A, unit 2.

3.6   Example 6GDBLE:UNIT=XM-B-1-4;

This command ends the blocking of XM in plane B, row 1, column 4.

50. Xem RP/EM:

Page 51: Tong Hop Lenh Ericsson

1.1   Command / \ |DEV=dev... | | | | / \ |RADRP:+ |dety...| +; |DETY=+ +[,PPS]| | |ALL | | | \ / | \ /

1.2   ParametersDETY=dety Device type

ALL All device typesDEV=dev DevicePPS Pre-Post Service If this parameter is given, then data is printed only for devices in Pre-Post Service State. If the parameter is omitted, then data is printed only for devices not in Pre-Post Service State.

2   Function

The command orders a printout of device RP/EM data.The printout DEVICE RP/EM DATA IN BSC is received forspecified devices, all devices of a device type, or alldevices.If the parameter PPS is specified in the command, thenonly devices which are in Pre-Post Service State will beincluded on the printout.If the parameter PPS is omitted, when only devices whichare not in Pre-Post Service State will be included onthe printout.Up to sixteen (16) such commands may be given simultaneously.All DEVICE RP/EM DATA IN BSC printouts are interruptedand terminated on commencement of an EXCHANGE DATA command,to prevent the possibility of out-of-date printouts beingobtained.The order does not remain after system restart.

50. Lệnh pint và tăng sae:

1.1   Command

/ \ / / \\|sae| | |block||

SAAEP:SAE=+ + |,BLOCK= + +|;|ALL| | |ALL ||\ / \ \ //

Page 52: Tong Hop Lenh Ericsson

1.2   Parameters

BLOCK=block Block name Identifier 1 - 7 characters

ALL All loaded blocksSAE=sae Size Alteration Event Numeral 0 - 8192 The maximum value is defined in the Operating System Area as highest usable SAE number.

ALL All defined SAEs

2   Function

This command is used to print file size information of Size Alteration Events (SAEs) defined in the system.The parameter SAE specifies the Size Alteration Eventnumber. The SAE type can be local or global. The table

indicates the number range for local and global SAEs:Table 1    SAE Type SAE number rangeGLOBAL 0 - 499LOCAL 500 - 899GLOBAL 900 - highest usable SAE number defined in the Operating System

AreaIf the SAE number specified in parameter SAE is oftype LOCAL, the parameter BLOCK must also be specified.If value ALL is specified for parameter BLOCK then file size information of the specified LOCAL SAE inall participating blocks are printed.If the SAE number specified in parameter SAE is oftype GLOBAL, the parameter BLOCK must not be specified.If parameter value ALL is specified for parameter SAEthen file size information of all SAEs defined in thesystem are printed. If a block name is specified togetherwith ALL for parameter SAE, then all SAEs defined in thespecified block are printed.The function uses the SAE database tables where all SAEs that are defined in the system are stored. If theSAE database tables are not complete, the function allowsfile size information of one SAE to be printed.The order does not remain after system restart.

3   Examples

3.1   Example 1

SAAEP:SAE=4;This command prints file size information ofof Global SAE 4.

Page 53: Tong Hop Lenh Ericsson

3.2   Example 2

SAAEP:BLOCK=RE,SAE=513;This command prints file size information ofLocal SAE 513 participated by block RE.

3.3   Example 3

SAAEP:BLOCK=RE,SAE=ALL;This command prints file size information ofall SAEs participated by block RE.

3.4   Example 4

SAAEP:SAE=500,BLOCK=ALL;This command prints file size information ofLocal SAE 500 in all participating blocks.

3.5   Example 5

SAAEP:SAE=ALL;

3   Examples

3.1   Example 1RADRP:DEV=RXTRA-1;Printout device RP/EM data for device RXTRA-1.

3.2   Example 2RADRP:DEV=RXTRA-33&&-47;Printout device RP/EM data for devices RXTRA-33 toRXTRA-47 inclusive.

3.3   Example 3RADRP:DETY=RXTRA,PPS;Printout device RP/EM data for all RXTRA-devices inPre-Post Service State.

3.4   Example 4RADRP:DETY=ALL;Printout device RP/EM data for all devices not in

Pre-Post Service State.L ỗi: FAULT CODE 6INVALID DEVICE TYPE SPECIFIEDdetails Command not permitted for this device type.

Page 54: Tong Hop Lenh Ericsson

FAULT CODE 7DEVICE TYPE DOES NOT HAVE PPS FUNCTIONdetails Device type does not have the Pre-Post Service state function associated with it.FAULT CODE 18NO DEVICE DATA AVAILABLE FOR OUTPUTdetails No device data available for output.FAULT CODE 29DATA CHANGE IN PROGRESS Command not allowed, data change command in progress.

51. Tăng SAE tự động:

1.1   Command

SAALI;

1.2   Parameters

-

2   Function

Command SAALI orders the execution of the Size AlterationEvents in the Size Alteration Action List.The command is terminated if the Automatic Size AlterationState is set Passive.The order remains after system restart.

3   Examples

3.1   Example 1

SAALI;The Size Alteration Events in the Size Alteration ActionList are executed.

52. Khai BPCs:

1.1   Command /RLBDC:CELL=cell[,CHGR=chgr]+[,NUMREQBPC=numreqbpc] \ [,NUMREQEGPRSBPC=numreqegprsbpc] [,NUMREQCS3CS4BPC=numreqcs3cs4bpc] \ [,TN7BCCH=tn7bcch]+;

Page 55: Tong Hop Lenh Ericsson

/

1.2   ParametersCELL=cell Cell designation

This is a symbolic name of a defined cell.CHGR=chgr Channel group number

Numeral 0 - 15 NUMREQBPC=numreqbpc Number of required BPCs

This parameter indicates the number of required Basic Physical Channels (BPCs) in a channel group. The parameter value must be specified as a multiple of 8.Numeral 8 - 128

SYSDEF System defined limitNumber of BPCs is defined by the number of frequencies in the channel group.

NUMREQCS3CS4BPC=numreqcs3cs4bpc

Number of required GPRS CS-3 or CS-4 BPCs

This parameter indicates the number of required BPCs in a channel group that can support General Packet Radio Service (GPRS) CS-3 or CS-4.Numeral 0 - 128

NUMREQEGPRSBPC=numreqegprsbpc Number of required EGPRS BPCs

This parameter indicates the number of required BPCs in a channel group that can support Enhanced General Packet Radio Service (EGPRS).Numeral 0 - 128

TN7BCCH=tn7bcch TN7 on BCCH frequency

This parameter indicates if Timeslot Number (TN) 7 on the Broadcast Control Channel (BCCH) frequency can be configured with Traffic Channels (TCHs) supporting EGPRS or GPRS only.

EGPRS TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

GPRS TN7 on the BCCH frequency can be configured with TCHs supporting GPRS only.

2   Function

Page 56: Tong Hop Lenh Ericsson

This command defines the number of required BPCs, and how many of the required BPCs that can support EGPRS or GPRS CS-3 or CS-4. It also defines if TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS or GPRS only.

The number of TCHs for a channel group can be calculated by subtracting the BPCs used for control channels from the number of required BPCs. If the number of required BPCs is set to system defined, the number of required BPCs is equivalent to the number of defined frequencies times eight. An extended range cell only configures half of the BPCs.

There must be at least one frequency defined per eight number of required BPCs.

It is not allowed to set the number of required BPCs so that the Stand-alone Dedicated Control Channels (SDCCH/8s) set in command RLCCC cannot be configured.

The number of SDCCH/8s and the number of required BPCs that can support EGPRS or GPRS CS-3 or CS-4 cannot exceed the number of required BPCs in the channel group.

The parameter TN7BCCH is only valid for channel group 0.

If channel groups have been defined for the cell using command RLDGI, then the CHGR parameter is mandatory.

The command is not valid for external cells, that is, cells belonging to another Base Station Controller (BSC).

The order remains after system restart.

3   Examples

3.1   Example 1RLBDC:CELL=HLM1,NUMREQBPC=8;

The required number of BPCs for the cell HLM1 is set to 8.

3.2   Example 2RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16.

3.3   Example 3RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=SYSDEF;

The required number of BPCs in channel group 1 in cell HLM1 is set to the number of BPCs defined by the number of frequencies in the channel group.

3.4   Example 4RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16,NUMREQCS3CS4BPC=4;

Page 57: Tong Hop Lenh Ericsson

The required number of BPCs in channel group 1 in cell HLM1 is set to 16. The required number of BPCs that support GPRS CS-3 or CS-4 in channel group 1 in cell HLM1 is set to 4.

3.5   Example 5RLBDC:CELL=HLM1,CHGR=0,NUMREQBPC=16,NUMREQEGPRSBPC=4,TN7BCCH=EGPRS;

The required number of BPCs in channel group 0 in cell HLM1 is set to 16. The required number of BPCs that support EGPRS in channel group 0 in cell HLM1 is set to 4. TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

53. Lệnh d ù ng để Tăng BPCs:

RLBDC:CELL=cell[,CHGR=chgr]+[,NUMREQBPC=numreqbpc] \ [,NUMREQEGPRSBPC=numreqegprsbpc] [,NUMREQCS3CS4BPC=numreqcs3cs4bpc] \ [,TN7BCCH=tn7bcch]+; /

1.2   ParametersCELL=cell Cell designation

This is a symbolic name of a defined cell.CHGR=chgr Channel group number

Numeral 0 - 15 NUMREQBPC=numreqbpc Number of required BPCs

This parameter indicates the number of required Basic Physical Channels (BPCs) in a channel group. The parameter value must be specified as a multiple of 8.Numeral 8 - 128

SYSDEF System defined limitNumber of BPCs is defined by the number of frequencies in the channel group.

NUMREQCS3CS4BPC=numreqcs3cs4bpc

Number of required GPRS CS-3 or CS-4 BPCs

This parameter indicates the number of required BPCs in a channel group that can support General Packet Radio Service (GPRS) CS-3 or CS-4.Numeral 0 - 128

NUMREQEGPRSBPC=numreqegprsbpc Number of required EGPRS BPCs

This parameter indicates the number of

Page 58: Tong Hop Lenh Ericsson

required BPCs in a channel group that can support Enhanced General Packet Radio Service (EGPRS).Numeral 0 - 128

TN7BCCH=tn7bcch TN7 on BCCH frequency

This parameter indicates if Timeslot Number (TN) 7 on the Broadcast Control Channel (BCCH) frequency can be configured with Traffic Channels (TCHs) supporting EGPRS or GPRS only.

EGPRS TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

GPRS TN7 on the BCCH frequency can be configured with TCHs supporting GPRS only.

2   Function

This command defines the number of required BPCs, and how many of the required BPCs that can support EGPRS or GPRS CS-3 or CS-4. It also defines if TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS or GPRS only.

The number of TCHs for a channel group can be calculated by subtracting the BPCs used for control channels from the number of required BPCs. If the number of required BPCs is set to system defined, the number of required BPCs is equivalent to the number of defined frequencies times eight. An extended range cell only configures half of the BPCs.There must be at least one frequency defined per eight number of required BPCs.It is not allowed to set the number of required BPCs so that the Stand-alone Dedicated Control Channels (SDCCH/8s) set in command RLCCC cannot be configured.The number of SDCCH/8s and the number of required BPCs that can support EGPRS or GPRS CS-3 or CS-4 cannot exceed the number of required BPCs in the channel group.

The parameter TN7BCCH is only valid for channel group 0.

If channel groups have been defined for the cell using command RLDGI, then the CHGR parameter is mandatory.

The command is not valid for external cells, that is, cells belonging to another Base Station Controller (BSC).

The order remains after system restart.

3   Examples

3.1   Example 1RLBDC:CELL=HLM1,NUMREQBPC=8;

Page 59: Tong Hop Lenh Ericsson

The required number of BPCs for the cell HLM1 is set to 8.

3.2   Example 2RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16.

3.3   Example 3RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=SYSDEF;

The required number of BPCs in channel group 1 in cell HLM1 is set to the number of BPCs defined by the number of frequencies in the channel group.

3.4   Example 4RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16,NUMREQCS3CS4BPC=4;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16. The required number of BPCs that support GPRS CS-3 or CS-4 in channel group 1 in cell HLM1 is set to 4.

3.5   Example 5RLBDC:CELL=HLM1,CHGR=0,NUMREQBPC=16,NUMREQEGPRSBPC=4,TN7BCCH=EGPRS;

The required number of BPCs in channel group 0 in cell HLM1 is set to 16. The required number of BPCs that support EGPRS in channel group 0 in cell HLM1 is set to 4. TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

54. Lỗi ABIS PATH UNAVAIL: 117. Note:  

In this result an ABIS PATH UNAVAIL(khong san co, khong co gia tri) fault may be received, this fault is also covered(che boi) by this OPI

Alarm ceasing printout:RADIO X-CEIVER ADMINISTRATION MANAGED OBJECTS IN TRANSCEIVER GROUP MANUALLY BLOCKED

1.1   CommandRXAPI:MO=mo,DEV=dev...,DCP=dcp...[,RES64K];

1.2   ParametersDCP=dcp

Digital connection point number used as termination point in the Base Transceiver Station (BTS) for the Abis pathNumeral 0 - 511

DEV=dev

Transmission device used for the Abis path

See Application Information for block TRAN for the format and value range of this parameter.

MO=mo Managed object instance

Page 60: Tong Hop Lenh Ericsson

See Application Information for block RXCTA for the format and value range of this parameter.

The Managed Object (MO) must be of class Transceiver Group (TG).RES64K A 64 kbit/s Abis path will be reserved for use by a suitably configured Time

Slot (TS) only.

2   Function

This command is used to define one or more Abis paths between the Base Station Controller (BSC) and the Base Transceiver Station (BTS).

Up to 124 Abis paths may be defined per TG. All Abis paths within a TG must be connected to devices of the same transmission type. See Application Information for block RBLT for valid transmission types.

Warning!

The setup of the transmission type must be considered when defining Abis paths as they may already be used by the transmission system for control purposes.

The first specified DEV argument is connected to the first specified DCP argument and the second specified DEV argument is connected to the second specified DCP argument, etc.

The answer printout RADIO X-CEIVER ADMINISTRATION ABIS PATH RESULT will show the results of the Abis path definition request.

The order remains after system restart.

3   Examples

3.1   Example 1RXAPI:MO=RXOTG-1,DEV=RBLT-1,DCP=1;

An Abis path is defined in BTS logical model G12 between the transmission device RBLT 1 and DCP 1 within TG 1.

3.2   Example 2RXAPI:MO=RXOTG-3,DEV=RBLT-2&&-4,DCP=4&&6;

Abis paths are defined in BTS logical model G12 between the transmission device RBLT 2 and DCP 4, the transmission device RBLT 3 and DCP 5 and between the transmission device RBLT 4 and DCP 6 within TG 3.

Page 61: Tong Hop Lenh Ericsson

3.3   Example 3RXAPI:MO=RXOTG-1,DEV=RBLT-1&&-31,DCP=1&&31;

Abis paths are defined in BTS logical model G12 between the transmission device RBLT 1 to RBLT 31 and DCP 1 to DCP 31 within TG 1. This means one 2 Mbit PCM system (or 1.5 Mbit PCM system in the USA) is connected.

3.4   Example 4RXAPI:MO=RXOTG-1,DEV=RBLT-1&&-31&RBLT-33&&-63,DCP=1&&31&33&&63;

Abis paths are defined in BTS logical model G12 between the transmission device RBLT 1 to RBLT 31 and DCP 1 to DCP 31, RBLT 33 to RBLT 63 and DCP 33 to DCP 63 within TG 1. This means two 2 Mbit PCM systems (or 1.5 Mbit systems in the USA) are connected.

3.5   Example 5RXAPI:MO=RXOTG-1,DEV=RBLT24-0&&-23,DCP=1&&24;

Abis paths are defined in BTS logical model G12 between the transmission device RBLT24 0 to RBLT24 23 and DCP 1 to DCP 24 within TG 1. This means one 2 Mbit PCM system (or 1.5 Mbit PCM system in the USA) is connected.

3.6   Example 6RXAPI:MO=RXOTG-1,DEV=RBLT24-0&&-47,DCP=1&&24&33&&56;

Abis paths are defined in BTS logical model G12 between the transmission device RBLT24 0 to RBLT24 23 and DCP 1 to DCP 24, RBLT24 24 to RBLT24 47 and DCP 33 to DCP 56 within TG 1. This means two 2 Mbit PCM systems (or 1.5 Mbit PCM systems in the USA) are connected.

3.7   Example 7RXAPI:MO=RXOTG-1,DEV=RBLT15-1&&-31,DCP=1&&31;

Abis paths are defined in BTS logical model G12 between the transmission device RBLT15 1 to RBLT15 31 and DCP 1 to DCP 31 within TG 1. This means one 2 Mbit PCM system (or 1.5 Mbit system in the USA) is connected.

3.8   Example 8RXAPI:MO=RXOTG-1,DEV=RBLT-1&&-31,DCP=1&&31,RES64K;

64 kbit/s Abis paths are defined in BTS logical model G12 between the transmission device RBLT 1 to RBLT 31 and DCP 1 to DCP 31 within TG 1 and are reserved for use only by TSs configured to use such paths. This means one 2 Mbit PCM system (or 1.5 Mbit system in the USA) is connected.

Page 62: Tong Hop Lenh Ericsson

55. LAPD:

4.1   LAPD Concentration

Figure 1    LAPD Concentration

A LAPD concentrator receives messages to several TRXs on one concentrated LAPD link connected to the BSC. The LAPD concentrator distributes the messages to the indicated TRXs via their respective dedicated non concentrated LAPD links. A LAPD concentrator also receives messages from several TRXs and transfers them to the BSC on the concentrated LAPD link.

4.2   Choise of TEI values

The TEI valus for TRXs must be unique within a LAPD Concentrator. Within one TG the TEIs are predefined to have unique values.

When concentrating LAPD links belonging to TRXs in different TGs, it may be neccessary to change the TEI values of the TRXs to get unique TEI values in the LAPD concentrator. This change must be done at the site.

Page 63: Tong Hop Lenh Ericsson

5   Glossary

CNC Equipment type connected to a concentrator board

CONCB LAPD concentrator boardCTSLOT Concentrated timeslotEM Extension ModuleLAPD Link Access Ptotocol for D-channelNCTSLOT Non-concentrated timeslotRILT Radio Interface Line TerminalTEI Terminal Endpoint IdentifierTG Transceiver GroupTRX Transceiver

56. Lỗi:A, Lỗi 1a:17- liên quan đến IDB, Ylink….(cần thay đổi post Ylink)B, Lỗi 1b:4- Liên quan đến anten, tỷ số VSRW….(có thể khắc phục ở angten, đổi feeder của cell đó).- Hiện tượng TRX OML fault do mất luồng hoặc nguồn cung cấp không đủ.57. Lệnh liên quan đến BPCs:

1.1   Command /RLBDC:CELL=cell[,CHGR=chgr]+[,NUMREQBPC=numreqbpc] \ [,NUMREQEGPRSBPC=numreqegprsbpc] [,NUMREQCS3CS4BPC=numreqcs3cs4bpc] \ [,TN7BCCH=tn7bcch]+; /

1.2   ParametersCELL=cell Cell designation

This is a symbolic name of a defined cell.CHGR=chgr Channel group number

Numeral 0 - 15 NUMREQBPC=numreqbpc Number of required BPCs

This parameter indicates the number of required Basic Physical Channels (BPCs) in a channel group. The parameter value must be specified as a multiple of 8.Numeral 8 - 128

SYSDEF

Page 64: Tong Hop Lenh Ericsson

System defined limitNumber of BPCs is defined by the number of frequencies in the channel group.

NUMREQCS3CS4BPC=numreqcs3cs4bpc

Number of required GPRS CS-3 or CS-4 BPCs

This parameter indicates the number of required BPCs in a channel group that can support General Packet Radio Service (GPRS) CS-3 or CS-4.Numeral 0 - 128

NUMREQEGPRSBPC=numreqegprsbpc Number of required EGPRS BPCs

This parameter indicates the number of required BPCs in a channel group that can support Enhanced General Packet Radio Service (EGPRS).Numeral 0 - 128

TN7BCCH=tn7bcch TN7 on BCCH frequency

This parameter indicates if Timeslot Number (TN) 7 on the Broadcast Control Channel (BCCH) frequency can be configured with Traffic Channels (TCHs) supporting EGPRS or GPRS only.

EGPRS TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

GPRS TN7 on the BCCH frequency can be configured with TCHs supporting GPRS only.

2   Function

This command defines the number of required BPCs, and how many of the required BPCs that can support EGPRS or GPRS CS-3 or CS-4. It also defines if TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS or GPRS only.

The number of TCHs for a channel group can be calculated by subtracting the BPCs used for control channels from the number of required BPCs. If the number of required BPCs is set to system defined, the number of required BPCs is equivalent to the number of defined frequencies times eight. An extended range cell only configures half of the BPCs.

There must be at least one frequency defined per eight number of required BPCs.

It is not allowed to set the number of required BPCs so that the Stand-alone Dedicated Control Channels (SDCCH/8s) set in command RLCCC cannot be configured.

Page 65: Tong Hop Lenh Ericsson

The number of SDCCH/8s and the number of required BPCs that can support EGPRS or GPRS CS-3 or CS-4 cannot exceed the number of required BPCs in the channel group.

The parameter TN7BCCH is only valid for channel group 0.

If channel groups have been defined for the cell using command RLDGI, then the CHGR parameter is mandatory.

The command is not valid for external cells, that is, cells belonging to another Base Station Controller (BSC).

The order remains after system restart.

3   Examples

3.1   Example 1RLBDC:CELL=HLM1,NUMREQBPC=8;

The required number of BPCs for the cell HLM1 is set to 8.

3.2   Example 2RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16.

3.3   Example 3RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=SYSDEF;

The required number of BPCs in channel group 1 in cell HLM1 is set to the number of BPCs defined by the number of frequencies in the channel group.

3.4   Example 4RLBDC:CELL=HLM1,CHGR=1,NUMREQBPC=16,NUMREQCS3CS4BPC=4;

The required number of BPCs in channel group 1 in cell HLM1 is set to 16. The required number of BPCs that support GPRS CS-3 or CS-4 in channel group 1 in cell HLM1 is set to 4.

3.5   Example 5RLBDC:CELL=HLM1,CHGR=0,NUMREQBPC=16,NUMREQEGPRSBPC=4,TN7BCCH=EGPRS;

The required number of BPCs in channel group 0 in cell HLM1 is set to 16. The required number of BPCs that support EGPRS in channel group 0 in cell HLM1 is set to 4. TN7 on the BCCH frequency can be configured with TCHs supporting EGPRS.

Page 66: Tong Hop Lenh Ericsson

58. Các từ viết tắt

1.2   Parametersarfcn Absolute Radio Frequency Channel Number (ARFCN)

It represents the frequency to which a Receiver (RX) or Transmitter (TX) is tuned, or the frequency associated with a timeslot handler.

HOP Frequency hoppingFor a TX, HOP is printed when synthesised frequency hopping.

bpc Basic Physical Channel (BPC) individualbspwr Base Transceiver Station (BTS) nominal power, expressed in dBmc0f Carrier zero filling

YES Carrier zero filling is turned on.

NO Carrier zero filling is turned off.

chcomb Channel combination BCCH

BCCH + CCCHSDCCH8

SDCCH/8 * 8SDCCH4

BCCH + CCCH + SDCCH/ 4 * 4CBCH8

SDCCH/8 * 7 + CBCHCBCH4

BCCH + CCCH + SDCCH/ 4 * 3 + CBCHTCH

TCHicm Idle channel measurement

ON Idle channel measurement performed

OFF Idle channel measurement not performed

mismatch

BTS capability mismatch specific reason for configuration selection failure BAND

Frequency band/system typeThe frequency band/system type of the Managed Object (MO) does not match the required frequency band/system type.

BTSPWR BTS powerThe value is within minimum and maximum power limits of the TX, but a value not allowed by the BTS.

BTSXRANGE Extended rangeThe function is not supported by the Timeslot (TS).

CELL Cell dedicationThe dedicated cell individual of the MO does not match the required cell individual.

CHGR Channel group dedicationThe dedicated channel group of the MO does not match the required channel group.

Page 67: Tong Hop Lenh Ericsson

MAXBTSPWR Maximum BTS powerThe nominal power of a TX exceeds the maximum power of the BTS.

MINBTSPWR Minimum BTS powerThe nominal power of the TX is less than the minimum power of the BTS.

NONE No mismatch

NPWR Nominal powerThe nominal power of a TX cannot satisfy that required by the cell.

RXDIV RX DiversityThe diversity capability of the RX does not match the required capability.

mo Managed Object Instance (MOI)

See Application Information for block RXCTA for parameter format.

modp MO of class Digital Path (DP)

morx MO of class RX

mots MO of class TS

motx MO of class TX

n1 Severely errored second estimatorn3 Errored second and severely errored second estimatorn4 Severely errored second estimatoroffs Frame number offset

The time difference from the Timing Function (TF) acting as master in another Transceiver Group (TG), expressed as a number of Time Division Multiple Access (TDMA) frames.

result Configuration data printout result BLOCKED

The MO is not in global state OPER and is therefore not available to the configuration function.

BPCFAIL An attempt to create a BPC individual has failed.

CONFIG The MO is configured with the indicated parameters.

FAILED An attempt to configure this MO was not successful.

N/A The MO is not of class RX, TG, TS, TX, or DP. Therefore configuration data is not appropriate.

SELECT The MO is selected for use but not yet configured. For an MO of class TS a speech/data path may not yet be setup.

UNDEF The MO is not defined.

UNUSED The MO is not configured, no other parameters are printed for this MO.

sbits Spare bits

Page 68: Tong Hop Lenh Ericsson

It sets the transmitted spare bits (Sa4-Sa8) in Pulse Code Modulation (PCM) time slot 0.

The TS is a binary number according to the following format: Sa8 Sa7 Sa6 Sa5 Sa4.

tn Time slot numbertxad TX logical address associated with a TX or a timeslot handler

HOP Baseband frequency hopping

xra Extended range YES

The time slot handler is an extended range time slot handler. It can support traffic at a distance of greater than 35 km between the mobile station and the base station.

NO The time slot handler is not an extended range time slot handler.

EOT DURING PRINTOUT The operator has cancelled the printout.

NONE No data existed to be printed.

AHOP NOT SUPPORTED BY TG Antenna Hopping (AHOP) is switched on, but the feature is not supported by the BTS.

CONFIGURATION DATA MAY BE INCONSISTENT A request to the TG for configuration status indicated that the configuration may have been changed. The data printed may be inconsistent.

CONFIGURATION IS SUSPENDED A request to the TG for configuration status indicated that configuration is currently suspended. The data printed may be inconsistent.

FLEXIBLE ABIS ALLOCATION NOT SUPPORTED BY TG Flexible Abis Allocation is switched on, but the feature is not supported by the BTS.

INCONSISTENT TRANSCODER CONNECTION TYPE The transcoder connection type for the TG is not consistent with the cell requirements.

INSUFFICIENT CS3CS4 CAPABLE EQUIPMENT Insufficient MOs of class Transceiver Controller (TRXC) or Interface Switch (IS), with suitable General Packet Radio Service (GPRS) Coding Scheme (CS) 3 or CS 4 capabilities are available within this TG to meet the cell requirements.

INSUFFICIENT EGPRS CAPABLE EQUIPMENT Insufficient MOs of class TRXC or IS, with suitable Enhanced GPRS (EGPRS) capabilities are available within this TG to meet the cell requirements.

INSUFFICIENT TRX EQUIPMENT Insufficient MOs of class RX or TS, with suitable capabilities are available within this TG to meet the cell requirement.

INSUFFICIENT TX EQUIPMENT Insufficient MOs of class TX, with suitable capabilities were available within this TG to meet the cell requirement at the time of configuration. If more TX equipment has become available since configuration was started the cell must be halted and activated to include these TXs in the configuration.

IRC NOT SUPPORTED BY TG Interference Rejection Combining (IRC) is switched on, but the feature is not supported by the BTS.

MAIO AUTOMATIC ALLOCATION PERFORMED The Mobile Allocation Index Offset (MAIO) list did not contain all valid MAIOs so the missing ones were added to the end of the list randomly.

MAIO EXCEEDS FREQUENCY SET SIZE

Page 69: Tong Hop Lenh Ericsson

The TG has invalid MAIOs, that is, MAIOs that exceed the number of frequencies in the hopping frequency set.

TF NOT SYNCHRONISED The MOs within this TG are not currently used to support the cell because the TF is not synchronised

FAULT INTERRUPTfault type

A fault interruption occurred during printing.

Fault type:

FORMAT ERROR The command was incorrectly specified.

UNREASONABLE VALUEdetails

The parameter was specified with an unreasonable value. FAULT CODE 2CANNOT MIX DIFFERENT BTS LOGICAL MODELSdetails

The MO parameter specified MOIs from more than one BTS logical model. FAULT CODE 6MO NOT IN VALID STATEdetails

The MOI is not in an appropriate state. The TG must not be in state UNDEF.

2   Function

This printout is received as an answer printout to command RXCDP.

It lists configuration data for MOs specified in command RXCDP. The configuration data indicates how MOs are configured to provide a number of BPCs, as well as the digital path configuration. When the contents of this printout indicate that frequency hopping is being supported, more detailed information may be obtained from the printout RADIO X-CEIVER ADMINISTRATION MANAGED OBJECT HOPPING DATA obtained using command RXHDP.

3   Action

This printout requires no action.

4   Printout Type

Answer printout

5   Printout Block

RXECOCRXOCOC

6   Glossary

AHOP Antenna Hopping

Page 70: Tong Hop Lenh Ericsson

ARFCN Absolute Radio Frequency Channel NumberBPC Basic Physical ChannelBTS Base Transceiver StationCS Coding SchemeDP Digital Path (Managed object)EGPRS Enhanced GPRSGPRS General Packet Radio ServiceIRC Interference Rejection CombiningIS Interface Switch (Managed object)MAIO The Mobile Allocation Index OffsetMO Managed ObjectMOI Managed Object InstancePCM Pulse Code ModulationRX Receiver (Managed object)TDMA Time Division Multiple AccessTF Timing Function (Managed object)TG Transceiver Group (Managed object)TRX TransceiverTRXC Transceiver Controller (Managed object)TS Time Slot handler (Managed object)TX Transmitter (Managed object)

7   References

7.1   Command DescriptionsRXCDP Radio X-ceiver Administration, Managed Object Configuration Data, PrintRXHDP Radio X-ceiver Administration, Managed Object Hopping Data, Print

7.2   Printout DescriptionsRADIO X-CEIVER ADMINISTRATION MANAGED OBJECT HOPPING DATA

7.3 Application Information RXCTA

59. Khai báo công suất:

1.1   Command / / \\ | |sctype||RLCPC:CELL=cell|,SCTYPE=+ +| | |ALL || \ \ /// \+[,MSTXPWR=mstxpwr][,BSPWRT=bspwrt][,BSPWRB=bspwrb]+;\ /

1.2   ParametersBSPWRB=bspwrb Base Station (BS) output power in dBm, for Broadcast Control

Page 71: Tong Hop Lenh Ericsson

Channel (BCCH) Radio Frequency (RF) channel numberNumeral 0 - 63

The current Base Transceiver Station (BTS) version may have specific parameter restrictions. See "BTS parameter limitations" in OPERATION AND MAINTENANCE MANUAL for current BTS version.

This parameter is not valid for external cell.BSPWRT=bspwrt BS output power in dBm, for non-BCCH RF channel numbers

Numeral 0 - 63

The current BTS version may have specific parameter restrictions. See "BTS parameter limitations" in OPERATION AND MAINTENANCE MANUAL for current BTS version.

This parameter is not valid for external cell.CELL=cell Cell designation.

This is a symbolic name of a defined cell.MSTXPWR=mstxpwr

Maximum transmit power in dBm, for Mobile Station (MS) on connection Numeral 13 - 43 in steps of 2 (GSM 800) Numeral 13 - 43 in steps of 2 (GSM 900) Numeral 4 - 30 in steps of 2 (GSM 1800) Numeral 4 - 30 in steps of 2 (GSM 1900)

SCTYPE=sctype Subcell type

This parameter is not valid for external cells.

UL The subcell type is underlaid.

OL The subcell type is overlaid.

ALL Both UL and OL.

2   Function

This command defines or changes configuration power data in a GSM cell or subcell. The command is not valid for external Universal Mobile Telecommunications System (UMTS) Terrestrial Radio Access Network (UTRAN) cells.

If a subcell structure exists, then SCTYPE must be specified for parameters MSTXPWR and BSPWRT. If a subcell structure exists and parameter SCTYPE is given with ALL, then BSPWRB can also be included with MSTXPWR, BSPWRT, or both, in the command.

Parameters MSTXPWR and BSPWRT are the only command parameters valid for underlaid (UL) and overlaid (OL) subcell.

If the cell is external, only parameter MSTXPWR may be specified with parameter CELL.

The order remains after system restart.

Page 72: Tong Hop Lenh Ericsson

3   Examples

3.1   Example 1RLCPC:CELL=HLM1,BSPWRB=33,BSPWRT=35;

This is an example of when a subcell structure does not exists.

The BS output power for the BCCH RF channel number is changed to 33 dBm and the BS output power for the non-BCCH RF channel numbers is changed to 35 dBm. The configuration data is assigned to cell HLM1.

3.2   Example 2RLCPC:CELL=HLM1,SCTYPE=OL,BSPWRT=38;

This is an example of when a subcell structure exists.

The BS output power for the non-BCCH RF channel numbers to the OL subcell in cell HLM1 is changed to 38 dBm.

3.3   Example 3RLCPC:CELL=HLM3,SCTYPE=ALL,BSPWRT=33,MSTXPWR=25,BSPWRB=35;

This is an example of when a subcell structure exists.

The BS output power for the non-BCCH RF channel numbers is changed to 33 dBm, the maximum transmit power for the MS on connection is changed to 25 dBm in a GSM 800 cell or a GSM 900 cell. The BS output power for the BCCH RF channel number is changed to 35 dBm. The configuration data is assigned to both UL and OL subcell in cell HLM3.

3.4   Example 4RLCPC:CELL=LIN4,MSTXPWR=26;

This is an example for an external cell.

The maximum transmit power for the MS on connection is changed to 26 dBm in a GSM 1800 or a GSM 1900 cell. The configuration data is assigned to cell LIN4, a cell belonging to another Base Station Controller (BSC).

60. xem route:

1.1   Printout: strsp:r=all; DEVICE STATE SURVEY R NDV NOCC NIDL NBLO RSTAT r ndv nocc nidl nblo rstat . . . . . . . . . . . . . . . . . . r ndv nocc nidl nblo rstat[NONE][EOT DURING PRINTOUT]

Page 73: Tong Hop Lenh Ericsson

/ \|FAULT INTERRUPT||fault type |\ / END

1.2   Parametersnblo Number of blocked devicesndv Number of devicesnidl Number of idle devicesnocc Number of occupied devicesr Route designationrstat Route status

BLOC Blocked

RES1 Reserved for priority calls

RES2 Reserved for non-overflow traffic

NORES No restrictions

61. Lệnh xem tài nguyên tổng đài:

SIZE ALTERATION OF DATA FILES INFORMATION

1   Format

1.1   Printout: saaep:sae=298; SIZE ALTERATION OF DATA FILES INFORMATION SAE BLOCK CNTRTYP NI NIU NIE NIR sae [block] cntrtyp [ni] [niu] [nie nir] / \ |fault type| \ // \ | . . . . . . . | | . . . . . . . | | . . . . . . . | | sae [block] cntrtyp [ni] [niu] [nie nir] | | | |/ \ | ||fault type| | |\ / | | | |[DBS DETECTED TRANSACTION ERROR] | | | | | |[EOT DURING PRINTOUT] | \ END

Page 74: Tong Hop Lenh Ericsson

1.2   Parametersblock Block namecntrtyp SAE Control Type CONS1 Software File Congestion Supervision CONS2 Congestion Event Control MANUAL Manual Control PROGRAM Program Control THRESH1 Threshold Control defined by the system THRESH2 Threshold Control defined by the application block ni Number of individuals The file size of Size Alteration Event. nie Number of individuals expansion size The file size expansion for the Size Alteration Event. nir Number of individuals reserved The file size of a Size Alteration Event that is reserved for automatic size increase. niu Number of individuals used The number of individuals in SAE that is being used by the participant block. A measure of the current utilization of a Size Alteration Event. sae Size Alteration Event (SAE)

Lệnh xem tài nguyên cell: SAAEP:SAE=…

3.1   SAE Number and Block Information

SAE number and block information, for each type of data file, is shown in Table 1.

Table 1    SAE Block Information

Data File SAE Block

Processor load control 000 LOAS

Internal cells 298 ROTRAN

External GSM cells 299 ROTRAN

External UTRAN cells 1133 ROTRAN

Page 75: Tong Hop Lenh Ericsson

Neighbour Relation Counter, Internal cells 522 RQCD

Neighbour Relation Counter, External GSM cells 523 RQCD

MS individuals 913 RMCC

MS individuals for signalling connection setup 500 RMSCS

UTRAN Cell Data relations 502 RQUCD

CHGR individuals 1152 RCCGD

TRXC individuals 1153 RXCMOO

62. Time zones:

1   Format

1.1   CommandCACAR:DATE=date[,TIMEZONE=timezone];

1.2   ParametersDATE=date Date

Expressed as yymmdd, where:

yy YearNumeral 00 - 99

mm MonthNumeral 01 - 12

dd DayNumeral 01 - 31

TIMEZONE=timezone

Time zone

If the parameter is omitted, the system time (time zone 0) will be used. The maximum value is defined in the Operating System Area.Numeral 0 - 23

2   Function

This command is used to remove a date from the calendar table. The day category value and the subday category value for this date then take on their default values.

The order remains after system restart.

3   Examples

Page 76: Tong Hop Lenh Ericsson

3.1   Example 1CACAR:DATE=991224;

The 24th of December 1999 for the system clock (time zone 0) is removed from the calendar table. The day category value and the subday category value for this date then take on their default values.

3.2   Example 2CACAR:DATE=991224,TIMEZONE=5;

The 24th of December 1999 for time zone 5 is removed from the calendar table. The day category value and the subday category value for this date then take on their default values.

4   Printouts

4.1   Check Printout

Yes.

4.2   Procedure PrintoutsEXECUTEDNOT ACCEPTEDfault type

Fault type:

FUNCTION BUSY The function is busy.

FORMAT ERROR The command or a parameter was incorrectly specified.

UNREASONABLE VALUEdetails

The parameter was specified with an unreasonable value.

4.3   Answer Printouts

This command has no answer printouts.

4.4   Result Printouts

This command has no result printouts.

5   Logging

Yes.

Page 77: Tong Hop Lenh Ericsson

6   Command Category Group

Recommended value 8 (H'8)

7   Command Receiving Block

JOB

8   Glossary

Time zone The calendar function has a system clock and time zones. The system clock is defined as time zone 0. Time zones greater than 0 define the time difference between system time and different regions to that of the system clock.

9   References

This document has no references.

63. Lệnh xóa channel group của cell:

1.1   Comm a nd RXTCE:MO=mo,CELL=cell,CHGR=chgr...;

1.2   ParametersCELL=cell

Cell designation.

Symbolic name, maximum 7 characters.CHGR=chgr

Channel Group.

A channel group is a part of the cell using a subset of the frequencies used in a cell.

Numeral 0-15.MO=mo Managed Object Instance.

See application information for block RXCTA for the format and the value range of this parameter.

Only managed objects of managed object class TG are allowed in the command.

2   Function

This command allows the operator to disconnect one or more channel groups from a transceiver group (TG) which has previously been defined. Only managed objects of

Page 78: Tong Hop Lenh Ericsson

managed object class TG are allowed in the command. The channel groups must also previously have been defined and halted.

The command is not allowed for external cells.

A maximum of 16 channel groups can be connected to a TG.

The order remains after system restart.

3   Examples

3.1   Example 1RXTCE:MO=RXETG-7,CELL=LIN3,CHGR=6&7;

The command disconnects the channel groups 6 and 7 in the cell LIN3 from TG 7 in BTS logical mode G01.

3.2   Example 2RXTCE:MO=RXOTG-9,CELL=LIN4,CHGR=0&&15;

The command disconnects the channel groups 0 to 15 in the cell LIN4 from TG 9 in BTS logical mode G12.

4   Printouts

4.1   Check Printout

Yes.

4.2   Procedure PrintoutsEXECUTEDPARTLY EXECUTEDfault typeNOT ACCEPTEDfault type

Fault type:

FUNCTION BUSY Function busy

FORMAT ERROR Format error

UNREASONABLE VALUEdetails

Unreasonable value

FAULT CODE 1 COMMAND NOT SUPPORTED FOR THIS MO

Page 79: Tong Hop Lenh Ericsson

The command is not supported for the specified managed object type.

FAULT CODE 4 WRONG MO CLASS

The specified managed object type has an unsuitable MO class.Only managed objects of managed object class TG are allowed in this command.

FAULT CODE 5 MO BUSY

The managed object instance is currently in use by another function.

FAULT CODE 18 THE SPECIFIED CELL DOES NOT EXIST

The specified cell has not been defined. Command RLDEI may be used to define a cell.

FAULT CODE 20 CELL CONNECTED TO A RADIO INTERFERENCE RECORDING INDIVIDUALdetails

The channel group cannot be disconnected due to radio interference recording for the associated cell. The cell must be removed from the recording identity using the commandRARDC.

FAULT CODE 28 CHGR NOT HALTEDdetails

The channel group is not halted. Command RLSTC may be used to halt a channel group.

FAULT CODE 29 CHGR NOT DEFINEDdetails

The channel group is not defined. Command RLDGI may be used to define a channel group.

FAULT CODE 32 CHGR NOT CONNECTEDdetails

The channel group is not connected to the specified managed object.

FAULT CODE 38 COMMAND NOT VALID FOR EXTERNAL CELLS

The cell specified is external and not allowed in the command.

FAULT CODE 20 CELL CONNECTED TO A RADIO INTERFERENCE RECORDING INDIVIDUALdetails

The channel group cannot be disconnected due to radio interference recording for the associated cell. The cell must be removed from the recording identity using the commandRARDC.

Lệnh thực hiện:

Page 80: Tong Hop Lenh Ericsson

Rarre:rid=…,Rardc:rid=…,Ramre:rid=…,Ramdc:rid=…,cell=…,

1   Format

1.1   Command

1.1.1   Format 1 / \ | | |CELL=cell... | | | |CELL=ALL,CSYSTYPE=csystype| | |RARDC:RID=rid,+ +; | / \ | | |arfcn... | | |ARFCN=+ + | | |ALLOCATED| | | \ / | \ /

1.1.2   Format 2 / \ | / \| | |cell...|| |CELL=+ +| | |ALL || | \ /|RARDC:RID=rid,+ +,REM; | | |ARFCN=arfcn...| | | \ /

1.2   ParametersARFCN=arfcn Absolute Radio Frequency Channel Number (ARFCN)

This parameter indicates the ARFCN for the carrier frequencies for which interference measurements will be made.Numeral 128 - 251 (GSM 800) Numeral 1 - 124 (GSM 900, P-band) Numeral 0, 975 - 1023 (GSM 900, G1-band) Numeral 512 - 810 (GSM 1900) Numeral 512 - 885 (GSM 1800)

ALLOCATED Measurements on the frequencies that are allocated in each cell respectively will be made.

Page 81: Tong Hop Lenh Ericsson

CELL=cell Cell designation

This is a symbolic name of a defined cell.

ALL All internal cells

CSYSTYPE=csystype

Cell system type GSM800

System Type GSM 800GSM900

System type GSM 900GSM1800

System type GSM 1800GSM1900

System type GSM 1900REM Remove specified frequencies

This parameter indicates that the specified cells or frequencies are removed from the configuration.

RID=rid Recording Identity (RID) for Radio Interference RecordingIdentifier 7

It is possible to have up to 10 allocated RIDs, named RIRID00 - RIRID09.

2   Function

2.1   Format 1

This command adds cells and frequencies to a Radio Interference Recording (RIR) definition. RARDC can be given several times for the same RID. No configuration on the Transceivers (TRXs) is performed before the command RARCI is given.

At least one cell must be specified before the frequency option ARFCN , can be given. A cell cannot be defined for more than one RID .

CELL=ALL is only accepted for RIDs in state ALLOCATED. If CELL=ALL is given, also CSYSTYPE must be specified. Then all cells with the specified system type are included in the RIR definition. Multi band cells are included as well, if their Broadcast Control Channel (BCCH) resides in the specified system type.

Cell list can contain cells with different cell system type.

The total number of frequencies for one definition (can be given by several RARDC commands) is limited to 150.

The argument for the parameter ARFCN can be specified in two ways: either by a discrete numeral value (test frequency) or by the string ALLOCATED.

When ARFCN is specified by test frequencies, all cells connected to the RID measure on those frequencies.

Page 82: Tong Hop Lenh Ericsson

The two ways of definition of ARFCN cannot be combined. If ARFCN is specified as ALLOCATED, then test frequencies cannot be added to the definition later on. However, if ARFCN is specified with test frequencies and later on an other RARDC redefines ARFCN as ALLOCATED, then the test frequencies are removed and replaced by the frequencies allocated in each one cell, connected to the RID.

ARFCN has a default value which is stated in Application Information for block RORIR.

The command is accepted for RIDs in state ALLOCATED, USED, CONFIGURATION COMPLETE or RECORDING COMPLETE. RID state can be checked with command RARRP.

After successful execution of RARDC, RID state is changed to USED.

For more information about the RID states see the Operational Instruction BSC, Radio Interference Recording, Administer .

The order does not remain after system restart.

2.2   Format 2

This command removes cells or frequencies from a RIR definition.

If all specified frequencies are removed from the definition, the frequency option ARFCN is set to the default value. The default value is stated in Application Information for block RORIR.

The command is accepted for RIDs in state ALLOCATED, USED, CONFIGURATION COMPLETE or RECORDING COMPLETE.RID state can be checked with command RARRP.

After successful execution RID state is changed to ALLOCATED if all cells are removed from the definition and to USED if at least one cell remains in the definition.

For more information about the RID states see the Operational Instruction BSC, Radio Interference Recording, Administer .

The order does not remain after system restart.

3   Examples

3.1   Example 1RARDC:RID=RIRID00,CELL=AIRPORT&CITY;

This example connects cells AIRPORT and CITY to RID RIRID00.

3.2   Example 2RARDC:RID=RIRID01,CELL=ALL,CSYSTYPE=GSM900;

Page 83: Tong Hop Lenh Ericsson

This example defines the RID RIRID01 to measure on all frequencies in all internal cells with the system type GSM 900. Also multi band cells, having BCCH in GSM 900 band, will be included in the definition.

3.3   Example 3RARDC:RID=RIRID01,ARFCN=ALLOCATED;

This example defines the RID RIRID01 to measure on the allocated frequencies in each cell, that are defined for RIRID01, respectively.

3.4   Example 4RARDC:RID=RIRID03,CELL=ALL,REM;

This example removes all cells defined for the RID RIRID03.

3.5   Example 5RARDC:RID=RIRID06,ARFCN=20&30,REM;

This example removes the ARFCNs 20 and 30 from the RID RIRID06.

RARDC:RID=RIRID06,ARFCN=20&&30,REM;

This example removes the ARFCNs 20 to 30 from the RID=RIRID06.

3.6   Example 6RARDC:RID=RIRID07,CELL=ALL,CSYSTYPE=GSM1800;

This example connects all cells with system type GSM 1800 to RIRID07, both single band and multi band cells are included.

RARDC:RID=RIRID07,CELL=MBC_B900_1800&SBC900;

The second example adds to the definition of RIRID07 a multi band cell MBC_B900_1800 with BCCH in GSM 900 and second frequency band in GSM 1800. A single band cell SBC900 with system type GSM900 can also be added to the same definition.

4   Printouts

4.1   Check Printout

No.

4.2   Procedure PrintoutsEXECUTEDNOT ACCEPTEDfault type

Fault type:

Page 84: Tong Hop Lenh Ericsson

FUNCTION BUSY The function is busy.

FORMAT ERROR The command or a parameter was incorrectly specified.

UNREASONABLE VALUEdetails

The parameter was specified with an unreasonable value.

FAULT CODE 3 CELL NOT DEFINEDdetails

The cell is not defined.

FAULT CODE 38 COMMAND NOT VALID FOR EXTERNAL CELLSdetails

The command must not be used for external cells.

FAULT CODE 71 CELL NOT CONNECTED TO THIS RIDdetails

Attempt to remove a cell not connected to the RID.

FAULT CODE 72 CELL ALREADY CONNECTED TO RID[details]

The cell is already connected to a RID. Note: If ALL was given in the command, no details will be given.

FAULT CODE 73 RID IN WRONG STATE

The RID is in the wrong state. See the Command Description RARRP and the Operational Instruction BSC, Radio Interference Recording, Administer.

FAULT CODE 76 FREQUENCY NOT CONNECTED TO THIS RIDdetails

The frequency is not connected to this RID.

FAULT CODE 78 ARGUMENT SPECIFIED TWICE IN COMMANDdetails

The argument has already been given in the command.

FAULT CODE 80 FREQUENCY ALREADY CONNECTED TO THIS RIDdetails

The frequency is already connected to this RID.

FAULT CODE 87 TOO MANY FREQUENCIES SPECIFIEDdetails

Too many frequencies are specified for one RID. The total number of frequencies for one definition is limited to 150.

Page 85: Tong Hop Lenh Ericsson

FAULT CODE 95 NO CELLS WITH SPECIFIED SYSTEM TYPE DEFINED

There are no cells of the specified system type defined for the Base Station Controller (BSC).

63. Tìm hiểu ACA:

5.2.17   Message Store

The function block Adjunct Processor Communication (ACA) is used for high speed reliable data transport from the CP to the AP through the Message Protocol to Adjunct Processor (MTAP) protocol. When the data arrives to the AP, the function Message Store Deamon (MSD) stores it safely. MSD does no interpretation of the data. To check the contents of the safe storage the command msdls can be used.

The function block in the CP that sends data to MSD is called MTAP, as is the protocol.

These are the alarms from MSD and MTAP:

AP MESSAGE STORE WARNING, see section Section 5.3.12 .

The ACA parameters the user is allowed to change and the permitted values of these parameters are described in the function block ACA application information.

64. Lệnh block device:

a,   Actions

Disconnect Device from Route 1. Is the ETC to be used for other functions?

Yes Go to Step 2. No Go to Step 5.

2. Block all devices in the digital path (DIP):

Use command BLODI .

Printout:BLOCKING RESULT

3. Block the DIP:

Use command DTBLI .

Alarm printout:BLOCKING SUPERVISION

4. Set the device to the pre-post service state:

Page 86: Tong Hop Lenh Ericsson

Use command EXDAE .

5. Disconnect the device from the route:

Use command EXDRE .

Remove Signalling Route? 6. Is the signalling route to be removed?

Yes Go to Step 7. No Go to Step 8.

Remove Route 7. Remove the route for signalling links:

Use command EXROE .

Job Completed 8. Make a report.

Note:   See Operational Instruction Report of Finished Work .

9. The job is completed.

3   References

3.1   Operational Instructions Report of Finished Work

3.2   Command Descriptions BLODI   BLOCKING OF DEVICE, INITIATE DTBLI   DIGITAL PATH TRANSMISSION FUNCTIONS, BLOCKING, INITIATE EXDAE   EXCHANGE DATA, PRE-POST SERVICE, DEVICE ACTIVATION, END EXDRE   EXCHANGE DATA, CONNECTION OF DEVICES IN A ROUTE, END EXROE   EXCHANGE DATA, SPECIFICATION OF ROUTE DATA, END

3.3   Printout Descriptions BLOCKING RESULT

BLOCKING SUPERVISION

4   Additional Information

No additional information is applicable to this document.

Page 87: Tong Hop Lenh Ericsson

5   Glossary

DIP Digital Path ETC Exchange Terminal Circuit PCD Pulse Code Modulation

Device

3.4 EXDUE:DEV=dev...;

This command disconnects devices from a Switching Network Terminal (SNT) unit.

Note:   For 155 Mbit/s Exchange Terminal (ET) it is possible to disconnect only a sequence of 32 devices, which is the default value defined for one SNT inlet.

The order remains after system restart.

3.5 exdri: dev=UPD1-34273&&-34303, r=VINA1CO&VINA1CI, misc1=3141;

MISC1=misc1

Miscellaneous information For value range see the Application Information for the relevant device block.

This command connects devices to a route.

For affiliated routes, indication is made to all the route names in the command

65. Lenh Reset giam sat kenh TCH, SDCCH:

RADIO CONTROL CELL SEIZURE SUPERVISION OF LOGICAL CHANNELS ALARM, RESET

1   Format

1.1   CommandRLVAR:CHTYPE=chtype;

1.2   ParametersCHTYPE=chtype Channel type

TCH Traffic Channel

SDCCH Stand Alone Dedicated Control Channel.

2   Function

Page 88: Tong Hop Lenh Ericsson

This command is used to order alarm reset of all unapprovedTCHs and SDCCHs for internal cells with seizure supervisionactive.All information about alarmed logical channels per channeltype (TCH,SDCCH) is cleared by this command, and can nolonger be printed. The order does not remain after systemrestart.

3   Examples

3.1   Example 1RLVAR:CHTYPE=TCH;Reset seizure supervision alarm for channel type TCH.

3.2   Example 2RLVAR:CHTYPE=SDCCH;Reset seizure supervision alarm for channel type SDCCH.

4   Printouts

4.1   Check Printout

Yes.

4.2   Procedure Printouts

EXECUTED

NOT ACCEPTEDfault type

Fault type:

FUNCTION BUSY        Function busy

FORMAT ERROR        Format error

UNREASONABLE VALUE         Unreasonable value

FAULT CODE 84NO ALARM GIVEN Alarm resetting ordered but no alarm had been given.

LENH XEM PROFILE:

Page 89: Tong Hop Lenh Ericsson

nsstp;gdstp;ioexp;c7spp:sp=all;ntcop:snt=all;dbtsp:tab=rps501boards;dphip;