Curriculum Vitae

GANESH D. PAWARM.Tech. (Electronics)Email-id : gpawar125@gmail.comMobile No.: 09404274802

OBJECTIVE

• To make a challenging career where I can apply my knowledge and skills to the best of my Potential, andthere by achieve career growth.

EXPERIENCE

• Working as a Research Engineer at R&D department in College of Engineering Pune.

Experience: 1st January 2016 to present

• Worked as Product Developer (Internship) at Hella India Automotive Pvt. Ltd. in Advance EngineeringDepartment.

Experience: June 2014 to May 2015

ACADEMIC DETAILS

Examination University Institute Year CPI/%PG Specialization: Electronics EngineeringM. Tech. Shivaji University,Kolhapur Walchand COE, Sangli 2015 7.85UG Specialization: Electronics and Telecommunication EngineeringB. Tech. Dr.B.A.T.U., Lonere Dr.B.A.T.U., Lonere 2012 6.8Intermediate/+2 Latur Board SDM, Latur 2008 71.83Matriculation Latur Board SMR, Latur 2006 76.67

Projects

• Tire Pressure Monitoring System◦ Company: Hella India Automotive Pvt.Ltd.,Pune◦ Description : Tire Pressure Monitoring System is fitted inside the tire. It is a sensor board designed to

monitor a tire pressure, air temperature inside a tire.This system transmits sensed information directlyon the dashboard of the vehicle or Smartphone.

◦ My responsibilities for hardware development of TPMS:

∗ Requirement Study∗ Reverse engineering∗ Design and Simulation of circuits∗ Testing of designed circuits on general purpose PCB∗ Report writing for conducted tests∗ Worst case calculations of circuits∗ DFMEA∗ Component Selection∗ Schematic Design∗ Testing of assembled boards

• RF Energy Harvester◦ Company: Hella India Automotive Pvt.Ltd.,Pune◦ Details : This device is designed by using a Schottky diode. The Dickson voltage multiplier circuit is

designed and input is matched to 50 Ohm. Ambient RF energy is used to charge Supercapacitor.Thisdevice gives an output of up to 20V depends on the strength of the ambient signal.

◦ Role : Concept study of various energy harvesting sources, Virtual simulation on LTspice for initialverification of design, Designing the hardware, Testing of designed circuits on general purpose PCB.

• Internet of Things (IoT) Laboratory Set up (Current Project)◦ Institute: Collage of Engineering,Pune◦ My responsibilities:

∗ Selection of different hardware boards for IoT∗ Study these hardware boards∗ Use these hardware boards for Research Projects

TECHNICAL SKILLS

• Hands on experience with ARM and 8051 microcontrollers

• Hands on experience with SPI,I2C,RS232,CAN protocols

• Design and development of analog and digital circuits

• Electronic circuits Simulation on virtual software

• Circuit building, prototyping and testing

• DFMEA of Electronic product

• Evaluation of different components

• Preparation of BOM

• Worse case calculations of electronic circuits

• Basic knowlage of EMI EMC testing

• Hands on experience with Raspberry Pi, Arduino boards for IoT

SOFTWARES USED

• KEIL for Assembly and Embedded C programming (ARM and 8051 microcontroller)

• Cadence Allegro for Schematic design

• LTspice,Proteus for circuit simulation

• Altium Designer for PCB Design (Basic level)

• IQRM for DFMEA

• Smith for impedance matching

ACHIVEMENTS

• Pat on the back award for my contribution in the TPMS project (Feb 2015)

• Qualified GATE 2013 and GATE 2014.

• Man of the Match and player of Winning team in Hella Premier League 2015.

• Winner of Technical Quiz VISION-2014 at Walchand College of engineering (Feb 2014).

• Runner-up of Hella Grandmaster-2015 at Hella India Automotive Pvt. Ltd.

ACTIVITIES AND INTERESTS

• Chief-coordinator of T&P Cell during 2013-2015.

• Worked as a coordinator of University Drama at university level (2010-11).

• Successfully organized and coordinated industrial visit (2013-14).

• Treasurer of TEESA committee for year 2011-12.

Place:Date: Mr. Ganesh Dilip Pawar