7/21/2019 MYKAQUAFIN1K

http://slidepdf.com/reader/full/mykaquafin1k 1/2

 MYK AQUAFIN -1KWaterproofing Slurry

Technical Data Sheet 

MYK Aquafin -1k  

Ver/2/Aug-2013 

Properties:

MYK AQUAFIN -1K is a rigid hardening, cement based

waterproofing material. MYK AQUAFIN -1K is made of

quartz sand, portland cement and additives. It does not

contain any materials, which may cause any negative

effects on reinforcement or concrete.MYK AQUAFIN -1K

hardens to a rigid impervious layer. If subsequent cracking

of the surface is possible, use MYK AQUAFIN -2K.

Scopes of use:

Waterproofing on concrete, masonry and plaster, for

interior and exterior use, in the following areas of

application:

Civil engineering: earth covered constructions,

sewage works, water tanks,

swimming pools, heating pipes,

pits etc.

Building construction: cellars, potable water tanks.

Water construction: storage lake walls, pools, tunnels,

sluices.

Older building not protected against posterior

constructions: moisture and soaking water.

Technical Data:

Basis: sand/cement, polymer improved

Specific gravity

of the ready mortar: 1.85 kg/l

Mixture: 25 kg MYK AQUAFIN -1K on

Instructions for Use:

MYK AQUAFIN -1K is supplied in powder form. It has to

be mixed on site with clean water in a clean vesse

until it becomes a workable mass that can be sprayed

or brushed. The surface should be pre-treated in thenecessary way. Application must be ensued in

several coats at a consumption of 1- 2 kg/m2 pe

coat. Green MYK AQUAFIN -1K coats have to be

protected against direct sun influence, draft air, rain

and frost.

Annotation:

MYK AQUAFIN -1K contains cement and reacts

alkaline with moisture. Therefore:

  Protect skin and eyes

 

Please keep out of children’s reach  In case of eye or skin irritation wash thoroughly

with clean cool water

  Wear safety gloves

  In case of eye contact seek immediate

medical treatment

   W

  a   t  e  r  p  r  o  o   f   i  n  g

 

p

g

 

Cleaning: in green state with water, dry

material is difficult to be 

removed

Standard DIN 1048, for potable

water uses acc. to DVGW, leaflet

W 270.

6.7 Lit tap water 

 Mixing time: 3 minutes

Pot life: 30 minutes @ 23ºC

Application temperature: + 5 C to + 30 ºC

Official certificate: impermeable to water acc. to

Storage: dry, 12 months in originallyclosed packs, opend packs are

to be sealed and be used up as

soon as possible.Consumption of the ready mixture/strength of layer:

Type of load 1  : earth moisture  :  3.5 kg/m²,  app. 2.0 mm 

Type of load 2  : ground water :  3.5 kg/m²,  app. 2.0 mm

  Type of load 3  : ground &

back water : 4.5 kg/m², app. 2.5 mm

walkable after 1 day

to pressure water after 7 days

Exposure*) : to rain after 3 hrs

*) at 25° C and 60% relative humidity.

Surface:

The surface must be of load bearing capability, largely

plain, free of pockets, cracks and ridges, free of foreign

matter, and free of oil, grease, paint or bitumen. Cement

paste and settleable solids have to be abraded. The

surface has to be moistened. Brick work areas have to be

built with joints in cement mortar. Existing gravel pocket

in the concrete as well as the bar spacers removed upto adepth of approx. 2 cm have to be filled with mortar (morta

group III) with the application of ASOPLAST-MZ. In

staggered corners, concave mouldings made of cemen

mortars usingASOPLAST-MZ have to be placed. During the

applicationand the time of hardening avoid large surface

ponding. Coarsepored surfaces cause a highe

consumption.

7/21/2019 MYKAQUAFIN1K

http://slidepdf.com/reader/full/mykaquafin1k 2/2

 

MYK Aquafin -1K

Ver/2/Aug-2013 

Quality Policy:

The information given in the date sheet is based on the

years of experience, and found correct to the best of

our knowledge. However the success of the product

& its application is dependent on many external factors.

We are fully assured of our products quality at the time

of dispatch. As we are constantly endeavoring to

enhance the qualities of our products which may reflect

changes it the data sheets. Hence in the event of any

doubt on critical parameters it is advisable to consult our

technical department

Technical Support:

Technical information regarding Schomburg range of

products can be obtained from the technical cell of

MYK Schomburg

Note:

Information in this technical data sheet is to the best of

our knowledge true and accurate. However, such

conditions under which our products may be used arebeyond our control, recommendations

MYK SCHOMBURG INDIA PVT LTD

(An Indo-German JV)

8-2-703/A, 3rd Floor, Leela Gopal Towers,

Road No. 12, Banjara Hills,

Hyderabad -500 034

Tel: +91 40 3040 0000

Email: mykschomburg.com

www.mykschomburg.com

  W  a  t  e  r  p  r  o  o  f  i  n  g